similar to: Error in ReceiveFax with T.38 -- Asterisk 1.6.0.7-rc2

Receiving a fax with 1.6.1: == Spawn extension (incoming-pstn-line, fax, 1) exited non-zero on 'DAHDI/4-1' -- Executing [fax at incoming-pstn-line:1] NoOp("DAHDI/4-1", "Fax Detected") in new stack -- Executing [fax at incoming-pstn-line:2] Goto("DAHDI/4-1", "incoming-fax,s,1") in new stack -- Goto (incoming-fax,s,1) --

Using spandsp-0.0.6-pre17, SendFax on 1.6.1.18 and ReceiveFax on 1.6.2.8. Sip.conf on both sides has t38pt_udptl = yes. -- Executing [s at fax-tx-test:3] SendFAX("SIP/side-sip-00000009", "/var/spool/asterisk/fax/20091113_1455.tif") in new stack [Mar 20 17:05:34] WARNING[6433]: app_fax.c:178 phase_e_handler: Error transmitting fax. result=49: The call dropped

To provide a reliable fax solution for users connected to a Asterisk 1.6.2.6 server i have tested a few T.38 capable ATA's: - Patton M-ATA - Grandstream HandyTone 486 - Fritz!Box 7170 I have tried Asterisk 1.6.2.6 compiled with SpanDSP-0.0.6pre17 and also Asterisk 1.6.2.6 with Fax for Asterisk installed. These Asterisk servers are connected to a Cisco PGW 2200 + AS5400XM. Sending fax

Hey guys I was hoping I could get a few pointers on a problem I have been trying to debug for the last couple of months regarding asterisk AGI scripts and unexpected termination. I have this agi script that accepts incoming faxes using RxFax on the latest asterisk 1.4 branch. Its written with perl and it works fine except for one line that causes the entire script to terminate unexpectedly. The

Receiving a fax pstn - pstn with 1.6.2.6-rc2: -- Executing [s at incoming-pstn-line:1] Answer("DAHDI/4-1", "") in new stack -- Executing [s at incoming-pstn-line:2] Wait("DAHDI/4-1", "3") in new stack -- Executing [s at incoming-pstn-line:3] Dial("DAHDI/4-1", "DAHDI/g0,36") in new stack -- Called g0 --

Hi, With 0.0.6pre3: # ./build.sh CMake Warning (dev) in CMakeLists.txt: No cmake_minimum_required command is present. A line of code such as cmake_minimum_required(VERSION 2.6) should be added at the top of the file. The version specified may be lower if you wish to support older CMake versions for this project. For more information run "cmake --help-policy CMP0000".

2009/2/26 Olivier <oza-4h07 at myamail.com> > I must add I tried spandsp0.0.6xxx as a warning message advised me to do so > (using 0.0.4 would be ok for me but current trunk doesn't allow this > anymore, it seems). > > > 2009/2/26 Olivier <oza-4h07 at myamail.com> > > Hi, >> >> With 0.0.6pre3: >> # ./build.sh >> CMake Warning (dev)

Hi! Have probably not understand how fax is working in Asterisk 1.6. I did install: ptlib-v1_12_0 h323plus-v1_19_7 dahdi-linux-complete-2.2.0.2+2.2.0 spandsp-0.0.5 asterisk-1.6.2 asterisk-addons-1.6.2 make menuselect in asterisk-1.6.2 source directory shows: [*] app_fax But "core show applications" doesnt show me any "fax applications" and when I try to receive a fax:

On 1.6.0.16-rc1: I'm using app_fax.so to send a fax, and then send a confirm. 'send' => 1. Set(UniqueFile=/var/spool/asterisk/outgoing/call-${UNIQUEID}) [pbx_config] 2. System(env echo -e "Channel:DAHDI/g0/........\\nContext:fax-tx\\nExtension: s\\nPriority: 1\\n" >${UniqueFile}) [pbx_config] [ Context 'fax-tx' created by

This message is pointed directly to Steve Underwood. I tought it would not be nice to directly email him with a question that interests a good part of the Asterisk community, so here it is. :) Steve, remember a few days ago when we discussed about issues on Asterisk 1.6.1.13 and T.38 fax reception? Well I opened an issue on Mantis (https://issues.asterisk.org/view.php?id=16756) and turns out it

Hello, Is anyone successfully using spandsp 0.0.2pre25 with either asterisk 1.0.x or 1.2.4? I've built a Gentoo ebuild for this version of spandsp and app_rtxfax, and it builds, but I'm not having any luck getting it working. 99% of my test faxes fail. Reverting to 0.0.2pre20 yields a much higher success rate. I've bumped the console debugging level in logger.conf to include debug

Dear folks, I couldnt receive faxes and get the following debug traces on the console, I appreciate any help or even hints. Using Spandsp-0.2 app_rxfax.c:76 span_message: FLOW Get at 9600bps, modem 1 app_rxfax.c:76 span_message: FLOW Changed from phase 3 to 5 app_rxfax.c:76 span_message: FLOW Non-ECM carrier up app_rxfax.c:76 span_message: FLOW Non-ECM carrier down app_rxfax.c:76 span_message:

Steve, I am trying to get tx_fax to work. I am using a TDM2401E card. I have a 3 page fax and I only receive the first page on every attempt. I think I have enabled debug output below. Can you tell me what the problem might be? I am using snapshot from oct 26. asterisk 1.2.13 and libtiff 3.6.1-12 from redat/centos 4.4. THanks, Jerry --------- Oct 28 13:13:40 DEBUG[22763]: app_txfax.c:69

Hello, I'm having difficulties to make Asterisk (1.6.0.6) interoperate correctly with a CISCO mediaGW in order to send faxes to the PSTN using T.38. When Asterisk sends the initial INVITE containing the T.38 media offer in the SDP, the CISCO answers with a 488 Not Acceptable Media. Apparently, it looks like a configuration problem in the CISCO, but I have tested the CISCO with the Zoiper

Hello, We have been working with the ReceiveFax application for some weeks now in order to receive faxes in T.38 and it works fairly well, but there are some faxes that for some reason we are not able to receive correctly. The asterisk version we are using is 1.6.0.6 with spandsp-0.0.5pre4 and the asterisk machine is behind a CISCO mediaGW to be able to communicate with the PSTN. The SIP call

hi folks. i recently upgraded asterisk to 1.6.1.17(from 1.2) and i'm having problems with fax. after receiving fax with the ReceiveFAX app. everything seems ok. the .tiff file was there, phone line seems to hang up. then asterisk will crash. any ideas? also i looked in the log file. this is what before it crashed: [Mar 8 12:12:12] WARNING[30115] app_fax.c: WARNING T.30 ECM carrier not found

Hi all I don't know what went wrong but i no longer seem to be able to compile asterisk. I first do : cd /usr/src/dahdi-linux-2.1.0.4 make clean ; make all ; make install cd /usr/src/dahdi-tools-2.1.0.2 ./configure ; make clean ; make all ; make install ; make config So far.... so good but then when i do : cd /usr/src/asterisk-1.6.0.6 make clean ; ./configure ; make all ; make install i

Well, my faxes passes through asterisk successfully, however I still have some problems about fax reception by rxfax. The softfax answers, and negotiates transmission, however then as some stage of communiation something is wrong. But I have nothing more but this log: Jun 2 00:10:21 DEBUG[16900]: chan_zap.c:4242 zt_read: DTMF digit: * on Zap/10-1 Jun 2 00:10:22 DEBUG[16900]: chan_zap.c:4242

more detailed output Sep 21 15:54:31 DEBUG[1120357296]: pbx.c:1255 pbx_extension_helper: Launching 'RxFAX' Sep 21 15:54:31 DEBUG[1120357296]: channel.c:1699 ast_set_read_format: Set channel Zap/1-1 to read format SLINR Sep 21 15:54:31 DEBUG[1120357296]: channel.c:1666 ast_set_write_format: Set channel Zap/1-1 to write format SLINR Changed from phase 0 to 1 Slow carrier up Slow carrier

Hi folks, I am having a small problem with asterisk-1.6.2.7 + app_fax on OpenBSD 4.7 -release. Everything seems to work fine. I have a macro which answers, receives the fax to a tiff, and then runs a script (mailfax) to convert that to pdf and email it. It all works perfectly except for some errors I am seeing in the console. After it hangs up I get a dozen or so messages in the cli