similar to: Incoming fax detection on mISDN hfcmulti B410P card

Hi, Until now I've been using my Digium B410P cards with misdn 1.0.x. I would like to upgrade my systems and am now wondering which is the "best" route to take: - use the latest release of misdn v1 - upgrade to the latest "stable" kernel and use the built-in misdn v2 - use misdn v2 as a seperate package (disable misdn in the kernel) - use dahdi's support for misdn

Hi. Using Asterisk 1.4.13 running on Ubuntu 7.04 with Intel CPU: 1) Not being able to build mISDN on Ubuntu using "make b410p" I have used mISDN-1_1_7 which seems to work ok. QUESTION: Should I expect this version of mISDN to work ok with these cards? Or is there a way to build using "make b410P" on Ubuntu? (make force does not help at all) 2) In some of our installations

Hi, I'm installing Asterisk on Ubuntu 6.10 When I first compiled the zaptel package I used: make clean make make install So far so good, but the following command failed: make b410p I did some digging on google and found a guide on how to install it manually, but the result was the same. I got these files ftp.digium.com/pub/telephony/zaptel/b410p/misdn-b410p.tar.gz

Put faxdetect = none in the misdn.conf and you'll be fine. -->> -----Original Message----- -->> From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users- -->> bounces at lists.digium.com] On Behalf Of Vieri -->> Sent: 06 February 2009 12:40 -->> To: asterisk-users at lists.digium.com -->> Subject: Re: [asterisk-users]

Hi list, I installed a fresh Debian/Etch with Asterisk 1.4 and Zaptel 1.4 from SVN for 2 Digium B410P card. I ran configure in Asterisk dir, went in zaptel dir and: make, make install, make b410p. Everything is ok. Now I want to compile Asterisk but can't activate the chan_misdn channel which depends on -from menuselect- isdnnet(E), misdn(E), suppserv(E) When I made the make b410p, all

Hello, I'm evaluating to possibility to use chan_misdn as a short term workaround, in case latest Dahdi is not stable enough for what we are planning to do (we wish to use Junghanns and Digium BRI hardware with Asterisk 1.6) . I've read www.mISDN.org but still have a couple of questions : 1. Is correct that in a 2.6.27 (and up) enabled kernel, the "embedded" mISDN version is

The DAHDI docs actually include the 'steps' that used to be in Zaptel's 'make b410p'. These steps involve downloading and compiling mISDN. Why re-invent the wheel? Just a thought :-). As for the 100ohm termination bit - it's simply changing a couple of dip switches on the b410p card (as described in the manual). Andy -----Original Message----- From:

Dear all, I know this is more a Digium hardware than an Asterisk issue. Already posted a question at Digium, however also like to see whether anyone in the Asterisk community has encountered the following situation: I installed a Digium B410P BRI PCI card on my new asterisk server, following the steps specified in the manual. I can see the PCI card is available using the lspci command: ...

Hi all! Sorry for my poor english, i'm italian. I installed Digium B410P on my asterisk server. I followed the official installation instructions found on digium site. These instruction, in my opinion, are not clear, so i tried with other ways (found on the trixbox site). I found this: http://www.trixbox.org/forums/trixbox-forums/trunks/howto-install-script-digium-b410p Now i can receive

Hi. I'm having problems with chan_mISDN configuration. Line "echotraining=yes" causes warning, when Asterisk is parsing misdn.conf and I'm confused why the PBX doesn't accept the setting. No matter which section I try to offer it, it is always invalid or out of range. The setting itself is supposed to be valid, it is in the sample configuration file of chan_mISDN 0.3.1.

Hi, I've been able to make make install the Zaptel drivers (1.2). I'm using a b410p so I executed the following command make b410p. I tried this on multiple machines, but it always failes: root@asterisk:/usr/src/zaptel-1.2.11# make b410p [ -f misdn-b410p.tar.bz ] || wget ftp://ftp.digium.com/pub/zaptel/b410p/misdn-b410p.tar.gz --23:59:54--

Hi, i use an BN4S0 with misdn an asterisk on Linux 2.6.9. The hfcmulti module is loaded with option: type=0x04 protocol=0x2,0x2,0x22,0x2 layermask=0xf,0xf,0xf,0xf and the fourth port is connected to an ISDN PTMP (MSN) port. Call to #72 from S0 (BN port 4) are not accepted from asterisk but why ? Can anyone give me a hint ?? misdn debug messages follows: lib: NEW_CR Ind with l3id:80001

Hello all, I'm trying to conect two asterisk servers using two B410p Digium cards. One card on each server. I just setting up the first BRI port on server A as nt_ptp and the first BRI port on server B as te_ptp. I use an ethernet wire to connect the first port of server A (nt_ptp) with the first port on server B (te_ptp) but the port light cotinues blinking on red on both sides once the

Hi list, Is Digium Wildcard B410P compatible with Asterisk 1.2 / 1.4 (zaptel of course) directly out of the box, or do I need things like bristuff? http://www.digium.com/en/products/hardware/b410p.php Best regards, Henrik Woffinden

Hi all, I wanted to switch from my current setup (mISDN) to the native dahdi with b410p support (wcb4xp). All works fine for normal phone calls but not for faxing. Faxes are distorted, if arriving at all, and hylafax logs the usual bad stuff (HDLC frame not byte-oriented.) Our setup uses a digium b410p card with asterisk 1.6, latest libpri and dahdi, hylafax with iaxmodem, and all this on 1

Hi list, we have a dual Xeon server with 2GB RAM running Debian Etch 2.6.18.4-686 kernel. The server has 2 B410P cards plugged in. No other card. We installed Asterisk 1.4 trunk with zaptel trunk, ran make b410p, the install mISDN1.1.0 (for bug 9064) configure and compile Asterisk with chan_misdn, all is fine. In misdn-init.conf we have added option=1,master_clock. Asterisk is up and

Hi, I have installed Asterisk 1.4 with mISDN with the install-asterisk.tar.gz script from beronet.com. On my system I have two cards, one a AVM Frit!Card Pci 2.0 and one HFC-S chip. I know both to work well with mISDN on my system from a previous installation. Now however, the AVM card works well at first glance, i.e. it "registers" incoming calls and works through the asterisk

Hi, I have 2 servers: one is running 2 B410P cards with 8 euroisdn lines (mISDN) connected on it, everything runs fine. I prepare a new server - HP 360 G8- with 2 HA8 cards each of them 1 module of 4 lines. Already had with this machine an RMA on both cards as they was faulty and crashed the server. What happends is that when I connect cables on the HA8 modules (those cables are unpluged

I'm using avm fritz card usb with kernel 2.6 patch with mISDN. The module is load correctly when I type lsmod I've got the following output: Module Size Used by zaptel 178308 0 avmfritz 21388 0 mISDN_isac 14336 1 avmfritz mISDN_dsp 191424 0 l3udss1 34184 0 mISDN_l2 39040 0

Hi all, I am having trouble setting the signalling method for the B410P using DAHDI. Asterisk complains that it has never heard of 'bri_cpe' or 'bri_net' - but it doesn't mind having 'pri_cpe' etc. ERROR[4294]: chan_dahdi.c:11327 process_dahdi: Unknown signalling method 'bri_net' Dahdi - dahdi-linux-complete-2.1.0.4+2.1.0.2 Asterisk - 1.4.23.1 Libpri - 1.4.9