similar to: chan_sccp and CISCO CP-7914 Module

Hi ! On Cisco 7960 (with or without 7914 add-on module) when I press speakerphone button (or select line with line button - which automatically put second line on speakerphone) after about 15-20 seconds of dialtone Asterisk stable dies (seg fault). Tested versions of Asterisk are 1.0.2, 1.0.3 or 1.0.5, chan_sccp is newest form CVS of chann-sccp.sourceforge.net ). Firmware of 7960 is

HI all: I have spent a large amount of time configuring/installing phones connected to Asterisk. Halfway through the process I discovered that my Cisco7960 with 2 7914 expansions was not supported in the SIP protocol. After reverting to SCCP 6.0(4.0) I am now perplexed with the hassle of configuring SCCP to properly work with Asterisk. So far I have gotten the phone to dial and receive calls

Hello ! I 'd like to connect Cisco IP phones to *. (7940 & 7960) Shall I use SIP or SCCP. Which approach provides better support of features of the Cisco IP phones ? Thanks ! Johann

release 20050730 http://chan-sccp.berlios.de/ <ftp://ftp.berlios.de/pub/chan-sccp/chan_sccp-20050730.tar.bz2> - very experimental hint (busy status line lamp or icon) support. This is a very experimental system so it might not work properly with particular cisco phones. 7960, 7970 and 7940 with recent firmware does work great. Old phones can't, of course, use the hint system. There

To get the SIP firmware for these phones, you need to buy a Cisco SmartNet support contract (about $75 USD in the USA, though I've heard rumors a Europe-only contract exists for about $10 USD.) You can purchase one through most Cisco resellers. That will give you access to Cisco's download site. Configuration of these phones under SIP is not quite as straight forward as it is with SCCP,

I'm still having problems getting this to work. I cannot get anything to display on my 7914 other than blank lines. I have SIP/5920-5930 in [main] that I'd like to add to the 7914 and indicate hook status. The 7960 is registering okay as SCCP/5000. What exactly should my sccp.conf file look like? When I make changes to this, how do I enact them? Do I reload Asterisk and reboot the phone

Hi, I am new to Asterisk and have some general questions _before_ I start buying equipent to install and get everything up-and-running. (this means I have no running Asterisk (yet)). I have read already a lot of doc, but some things are not clear to me, since I'am inexperienced in Asterisk and PBX. The goal: Make PBX using Asterisk and Cisco 79xx equipment for 25 phones (1 x 7970, 4 x 7960,

http://chan-sccp.berlios.de/ 20050713 ftp://ftp.berlios.de/pub/chan-sccp/chan_sccp-20050713.tar.bz2 I didn't have a spare 7960 to use this week, so maybe some line issue is still present. - fixed a memory leak on database updates (dnd, cfwd*) - fixed old memory leak on unload (now unload chan_sccp.so and load chan_sccp.so work. It does reload the config when asterisk is running) - socket

ive got asterisk running with chan_sccp and three cisco phones (2 7910's and 1 7960). lots of bugs. when i press the speed dial button on either 7910, asterisk dies. also, if i dial from the 7910 to 7910, everything works fine. i can dial from or to the 7960 once, and then one of the 10's and the 60 die and try to reregister. if i take the 7960 out of the mix and remove its

The documentation of how to use the 79xx series' phones and features with Asterisk is really hard to find and put together. The higher end phones like 7970 are more like converged PC+phone, a thin client to telephony and network apps. But it's really hard to target it as a development and deployment platform because the docs and techniques are so obscure. There seems to be a fair amount

I was wondering if anyone had any experience getting a 7960+7914 working with any of the chan_sccp modules. I've got a 7960G with 6.0(5.0) and a factory fresh 7960G with 3.1(MF.G2). I've got 2 7914s fresh out of the box brand new. I hook them up and all I get is red lights on all of the buttons. When I go into the phone to see what version firmware they have it says "Link State:

Hi, This is a message I already posted on the chan_sccp mailing list, but since this list has a lot of active members, I'm hoping someone might be able to help (And my problem is * related, so I guess it's ok if I post it here also ;) ). I'm trying to get SCCP ATA188s to run with Asterisk. The Asterisk box uses the latest Asterisk@Home image (Version 2.6). I have compiled and

Dear sccp users :-) We are announcing the support of the Cisco 7935 Conference Station within the chap_sccp channel driver (experimental version) AND the "alpha-beta" stage of the 12SP+ Support. I will later on today add the information on the Wiki on how to get this phones correctly registered. However the support is still not fully functional (some issues), but please test this

I have been trying for sometime to upgrade this phone to either sip, or the latest sccp (at this point I don't care) with no success. It has an sccp image (don't know the version off the top of my head) that is incompatible with chan_sccp. When I boot up the phone, it asks the tfpt server for the .tlv file, then the SEP<mac> file which it receives successfully. It then asks for

Just attended the Cisco Networkers conference and sat through a presentation addressing in part the Cisco IP phones. All was presented openly without the need for disclosures, etc. The following is simply an FYI from the presentation, FWIW. Existing IP Phones (7905/7912/7940/7960): Transport: UDP Call Signalling: rfc2833 Security: Digest Auth Feature parity to SCCP: None Sip Enhanced

On Sat, May 28, 2005 at 01:51:56AM +0200, Stefan Gofferje arranged a set of bits into the following: > Hi folks, > > I'm trying the latest mayday chan_sccp and found it difficult to have > more than three speeddials. I have defined only one line but can't get > more than three SDs. On console, * says > > May 28 01:44:12 ERROR[26933]: sccp_actions.c:252 >

Greetings, I have seen a few postings in the past regarding the interop of Asterisk and the Cisco 7920 WiFi phone. To date, I have not seen a definitive method to getting the phone working. Assuming someone has this actually working, can that person step up and answer these questions. 1) What Channel is it working with (chan_skinny or chan_sccp)? 2) If code was used that is not a part of a

Hi Siggi/Jan, >If so, there's still a load version conflict (although I've >never seen a >7960 or 7940 care about the version communicated through SCCP): > >On the phone, press "Settings", then 4 for load information. >watch out for the "App-Load-ID". On my 7940, this is >"P00305000300". Yours >is most likely a smaller number... >

Ok, so multiple people have said that hinting is possible with chan_sccp on the 7940/7960's and such, has anyone got this working? How do you go about getting this to work? I'd use the wiki, but it's link to the mailing list topic on that doesn't work anymore :( -- Aaron Daniel Computer Systems Technician Sam Houston State University amdtech@shsu.edu (936) 294-4198

I found a few mentions of the 7914 being used with Asterisk, these all covered SCCP/skinny though. Does anyone know if the 7914 can even be used with SIP? If so, any pointers? Is it a services thing? Anyone get the operator (line/extension status) to work with it. Thanks for the help, Cisco doesn't even mention ANYTHING about SIP + the 7914. Matt