similar to: HFC Single port Cards

Subsequent to some previous E-Mails, I've been trying to dig into the ISDN - BRI situation a bit more. I have determined that I have a HFC card with Winbond chip, but I'm not sure what combination of drivers is best or usable. zaphfc is out because it only supports the cologne chip. misdn is a possibility. I haven't determined if it supports the card natively, or needs a card

Mine is very similar: i don't have echocancelwhenbridged=yes because it seems work only on TDM, is it ? And in Italy, I often have set pridialplan = unknown About echo I have some problems, but only at the beginning of the call. After 3-4 seconds the echo became almost null, specially with snom 190; with pa168s and ywh10 I have again some problem, the echo come up also after 1 minute of

Hi! I have installed two hfc-s cards to handle my pstn calls. I use mISDN with capi, so capi.conf is edited. I have tested both separate and cards are working well. But they are not working together. It seems that when i set up settings for the other card: ;capi.conf: [general] nationalprefix=0 internationalprefix=00 rxgain=0.8 txgain=0.8 [interfaces] msn=50 incomingmsn=* controller=1

Hello, I am having problems, getting my asterisk-domU to work properly. It consists of the following components: - Debian Etch under Xen-3.1 with a 2.6.18-kernel - Asterisk 1.2.24 - mISDN-1.1.5 I have 2 HFC-ISDN-cards, which I pass through to the Asterisk-DomU in permissive mode. This is working fine. The strange problem is, that the two HFC-ISDN-cards are not beeing initialized by the

I had Asterisk 1.6.2.2 running fine with a mISDN using a HFC-S based card. I installed my TDM400P into the PC, it's really slow to boot now, when it finally does I gets stuck in a loop of reporting "isac xdu no tx_busy". Anyone able to assist? Thanks in advance! -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello everyone. I've got this really annoying HFC Cologne card (or however I should call it - a single channel ISDN card based on the HFC chipset). It wrongfully detects lots and lots and lots of incoming DTMFs, to the point the card is not usable. Here's a sample out of CLI: P[ 1] I IND :DTMF_TONE oad:206361 dad:520101 P[ 1] --> mode:TE cause:16 ocause:16 rad: cad: P[ 1] -->

hi list, I'm currently trying to get Asterisk running with an HFC-compatible ISDN card (no-name product, but supposed to work with Asterisk according to the packaging). the ISDN-card is connected to a alcatel ISDN-system where it should act just like a normal ISDN-phone. I went with http://www.misdn.org/index.php/MISDN_with_Asterisk and installed the package from beronet.com including:

Hi Guys, I got 2 internal HFC-S[5] (not sure what character this is) internal modem cards yesterday, thought I would get different makes as the one was a named brand, the other not... but anyway... Its picked up by lscpi as a ... "Network Controller: Cologne Chip Designs GmbH ISDN network controller [HFC-PCI] (rev 02)" I'm using kernel 2.6.10, and I saw I must use CAPI. I

Hi All, I'm trying to use a HFC chip ISDN modem with mISDN and chan_misdn. The card is configured to NT, PmP mode. One Siemens ISDN phone connected to the modem. When I call the ISDN phone is called everything is just fine, but when I call from the ISDN phone I face some problems. - There is no dial tone when I pick up the handset. - I call a number but there is no ringtone and after I

Hi, I have installed Asterisk 1.4 with mISDN with the install-asterisk.tar.gz script from beronet.com. On my system I have two cards, one a AVM Frit!Card Pci 2.0 and one HFC-S chip. I know both to work well with mISDN on my system from a previous installation. Now however, the AVM card works well at first glance, i.e. it "registers" incoming calls and works through the asterisk

Hi All I'm having problems posting to this list, no bounces the mails just dont show any advice how to get the postings through is there filtering? robb

hello, anyone has worknig ISDN hfc-pci card in DDI (DID) point2point mode? what kernel ? and second question mISDN driver .. anyone has working solution with mISDN and maybe fritz card? what you suggest for DDI -> point2point mode (card,kernel,chan_..., ...) ? thank you, Tomaz

I've just found my first problem. /dev/mISDN was being created with the wrong permissions... Thanks James > -----Original Message----- > From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users- > bounces@lists.digium.com] On Behalf Of David Phelan > Sent: Monday, 20 March 2006 12:18 > To: 'Asterisk Users Mailing List - Non-Commercial Discussion' >

Hi I have looked through the wiki and search the mailing list, but I cannot find a way to intrude on a call, can asterisk do this feature? if so how? Thanks for your help Robb

Hi, I'm in the process of setting up Asterisk in a SOHO environment using ISDN for trunking. More specifically a BRI 2B+D circuit where one SPID is used for the business and the other is used for personal. The circuit already exists, but is presently being interfaced to POTS phones via a TA. This configuration is not very common in the US, but we are fortunate that our LEC offers it price

Hi All I cannot seem to find a way to stop atserisk inercepting DTMF tones and regenerating them even on a zap to zap bridged call is this possible? Thanks Robb

> Hmm, > > I was using 0.3.0 rc24, or the unstable branch. I see 0.2.0 is listed as > 'stable' so maybe I should have used that. Please do keep me informed of > your progress. > > Craig After finally getting chan_misdn to load (missing #include to bitops.h under Debian at least) it still won't load, and won't tell me why even with all the debug stuff

Hi, I would appreciate some advice on the following: how does one use a single BRI port HFC chipset based ISDN cards with the latest DAHDI, libpri and Asterisk 1.8? For Asterisk 1.4 I would first install mISDN & mISDNuser and then build Asterisk 1.4. Now I noticed that Digium's HFC chipset based B410P is supported by the latest DAHDI & libpri but reading the source of the

Hi all, I have a problem: On my internal S0 where phones are connected via HFC I get all the number with a leading 0 (either from internal SIP phones or external dialins via CAPI). I don't know where to look for this 0. Any ideas? Greetings, Sven -- Sven Fischer (Dipl.-Phys.) - FACIT Consulting GmbH Hausinger Str. 6 - 40764 Langenfeld Tel: 02173/16700-55 Fax: 02173/16700-60

Greetings to everyone! I am new to Asterisk and ISDN modules so i tried to follow many of the articles about capi, bristuff, mISDN and so on. Now I am working in mISDN but every way I try I have compiling errors! The HFC PCI card is a Digi Datafire Micro V. The bristuff give me the error "invalid module format zaphfc.ko" and I don't know how to compile and load it. The capi