similar to: sound quality between two back-to-back asterisk

Hi, Is it possible to connect Asterisk with a mobile base station to handle call switching? What kind of protocol will I need to use to convert to sip? Any pointer or info will be greatly appreciated. Best Regards, Mark -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20081119/e74ef6b1/attachment.htm

After upgrading from 1.2.x to 1.4.x call detail records are not being written to /var/log/asterisk/cdr-csv/Master.csv In cdr_manager.conf I have [general] Enabled = yes Apparently there is something else that needs to be configured for call detail records in 1.4.x. Can someone point me in the right direction? Don Pobanz

Hi, I have a Linksys SPA 3102 using as ATA. The call routing is : Phone -> PSTN -> SPA 3102 -> SIP Proxy -> Asterisk The problem I am having is that when the phone hangs up, SPA 3102 can't detect it and relay the CANCEL message. Is this problem with my SPA 3102 config or it just works like that by default? Thanks in advance for your help. Regards, Mark -------------- next

I have incoming analog and SIP DIDs that all ring multiple sip extensions with a Dial command as the first exten. I am curious to know if it's possible for the incoming caller to transfer out of the Dial command while in progress and dial a single extension? Thanks! jlc

My application fires several calls thru AMI ORIGINATE command. For example if I have 3 operators I do 3 ORIGINATEs. My trouble is when one operator quit for some reason, I should kill the corresponding ORIGINATE. Of course, I could let the call ring and hangup after the customer pick-up. But this is not the case, I do have to kill the corresponding ORIGINATE. I could execute a soft hangup,

Hi I am working on deploying voip for my company and would like to seek some advice on the number of E1 lines we need to rent. Our telco told us that there can be at most 30 concurrent channels on an E1 line. Typically, what is the maximum number of DIDs that we can allocate to that E1 line before users get frequent "all lines are busy"? We are running a support center with mostly

Hi folks, Is it possible (asterisk 1.6) to trigger the playback of an audio file in the middle of a call using the Manager Interface? I'm looking for something like AMI PlayDTMF command but for audio files. Thanks a lot, G. -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello everyone, I am having a bit of problem getting MusicOnhold to play. I am running Asterisk 1.4 with MPG123 0.59 installed. And here's what i see in the debugging window of asterisk: -- Started music on hold, class 'default', on channel 'SIP/x123-082043d0' -- Stopped music on hold on SIP/x123-082043d0 Any idea why it is not playing the file at all? thanks

I have a TE210P digium card that has 2 E1/T1 ports. the code in my extensions.conf file for span 1 is : [globals] CONSOLE=Console/dsp ; Console interface for demo TRUNK=Zap/g1 ; Trunk interface TRUNKX=Zap/g2 ; 2nd trunk interface ... ... ; dial a long distance outbound number to SPAIN ; This

Hey, all. I was just wondering if there were any tools/utilities/what-have-you out there that would allow a user to click on a contact in Outlook, and have their phone dial it? (Or, I guess, have Asterisk dial both their phone and the destination number, and put the two into a conference.) Thanks! -Ken -- This message has been scanned for viruses and dangerous content by MailScanner, and is

Hello Happy New Year! I succesfully installed the Ports of Zaptel BSD 1.4.0 and Asterisk 1.4.13 (that's the latest in the Ports). To save CPU, I'd like to play PCM WAV files instead of eg. GSM. Per... www.voip-info.org/wiki/view/Convert+WAV+audio+files+for+use+in+Asterisk ... I recorded a sample of my voice using XP's Sound Recorder, then ran the following : sox test_wav.wav -r

Hello may situation is the next: Asterisk <--> NAT1 (router)<---> internet <--> NAT2 (router) <--> x-lite ^ | ip phone (cisco) Asterisk and de cisco phone are in the same LAN. I want to make a call between the x-lite and the ip phone. I can do the call but there is only audio from de ip-phone

Hi all, I am running an AGI script in a command dial, or call a SIP trunk. I want to execute after 10 minutes a voice message (stream file) on the channel to warn the person that the call is about to end. How to do that? Thank you, Mickael. -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi all, I am using Digium PCI board to receive PSTN call through regular phone line. It is no problem for me to receive calls, but I am not able to obtain the Caller ID if the calls are from the phone line. exten => s,1,Answer() exten => s, n, Verbose(1|incoming number is ${CHANNEL} calling to ${EXTEN} routing to ${phonenum} ) exten => s,n, Verbose(1|callid is ${CALLID(num)}) exten

Hello, I want to create channel bank in this case: "channel bank" |-----------------------------------------| | FXS,FXO<----->TDMoE<--|---------------------------------->Asterisk |-----------------------------------------| How can it?

Hi, I have a requirement, whenever a user comes into the conference, it has to announce the user name to all the person who are all available in the conference. I have used Meetme(,di) where i is to announce the user leave/join with review. I user used I also, which is to announce the user leave/join with out review. In both the above cases, it is prompting the user to say their

Dear friends, I am having problem with running a sample php and I can't figure out why. I can run the sample.php using CLI but when I run it inside the dialplan it does not work. Can someone please suggest the config problem that I may have made? dommy:/var/lib/asterisk/agi-bin# php sample.php #!/usr/bin/php5 -q VERBOSE "Here we go!" 2 VERBOSE "Call from - Calling

I want to use Asterisk as a general message delivery system here. That is, I want to be able to have a (shell, perl, etc.) script on my Asterisk server dial an extension, wait for it to be answered and then play a sound file and then hang up, or even wait for a response or reactions to some IVR. Certainly if I had a SIP library, I could have the script simply look like a SIP extension but that

Hi All, My research indicates ANI is not really supported with SIP Channels or passed between SIP servers, even with setting function CALLERID(ANI). So the only place this applies is on PRI interfaces, when sending calls out a ZAP PRI you can set the ANI to whatever and CID Number to a different whatever so on the other end of the PRI you will receive the two different values? Is this correct or

I'm looking to connect a BMC 450 to an asterisk with a Digium Quad E1 card. Am I right in thinking that I'll need a special 'crossover-E1' RJ45 cable? If so, any clues where I might buy one in the UK? The Digium card sellers don't seem to stock such a thing. Thanks. Tim. Tim Panton - Web/VoIP consultant and implementor www.westhawk.co.uk