similar to: B410P and asterisk 1.6

Hi, Since a week ago I am trying to get chan_misdn working with asterisk 1.4.19, using HFC based ISDN card on Linux 2.6.22. My setup is done as detailed on wiki and FAQ. * mISDN and miSDNusers are 1.1.7.2, unpacked, build and installed. After installation and misdn-init, I have this: aragorn:root/pts/1: # misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) ->

Hello, I'm evaluating to possibility to use chan_misdn as a short term workaround, in case latest Dahdi is not stable enough for what we are planning to do (we wish to use Junghanns and Digium BRI hardware with Asterisk 1.6) . I've read www.mISDN.org but still have a couple of questions : 1. Is correct that in a 2.6.27 (and up) enabled kernel, the "embedded" mISDN version is

Have you got termination set correctly? I have a B410P working with 2 x NT and 2 x TE ports successfully. I had to turn the 100ohm termination on on the NT ports (even though I have them set as PTP in mISDN.conf). HTH -->> -----Original Message----- -->> From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users- -->> bounces at lists.digium.com] On

I have used the b410p card with Asterisk 1.12 quite successfully. I now want to get the card to work with Asterisk 1.4.0beta3. It however can't seem to get chan_misdn compiled. In menuselect, chan_misdn has this: Depends on: isdnnet, misdn, suppserv Can anyone help? -- thanks, yusuf -- This message has been scanned for viruses and dangerous content by MailScanner, and is believed to

Hi, Until now I've been using my Digium B410P cards with misdn 1.0.x. I would like to upgrade my systems and am now wondering which is the "best" route to take: - use the latest release of misdn v1 - upgrade to the latest "stable" kernel and use the built-in misdn v2 - use misdn v2 as a seperate package (disable misdn in the kernel) - use dahdi's support for misdn

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all, We have a BRI installation who is experiencing constant echo with the Digium b410p and mISDN. I have adjusted gains, and originally thought that the desktop phones were at fault, although we experience the same problem when a call is bridged out to an external number. I've tried it with 128 taps (the default and I believe the supported

Hi list, we have a dual Xeon server with 2GB RAM running Debian Etch 2.6.18.4-686 kernel. The server has 2 B410P cards plugged in. No other card. We installed Asterisk 1.4 trunk with zaptel trunk, ran make b410p, the install mISDN1.1.0 (for bug 9064) configure and compile Asterisk with chan_misdn, all is fine. In misdn-init.conf we have added option=1,master_clock. Asterisk is up and

Hi list, I installed a fresh Debian/Etch with Asterisk 1.4 and Zaptel 1.4 from SVN for 2 Digium B410P card. I ran configure in Asterisk dir, went in zaptel dir and: make, make install, make b410p. Everything is ok. Now I want to compile Asterisk but can't activate the chan_misdn channel which depends on -from menuselect- isdnnet(E), misdn(E), suppserv(E) When I made the make b410p, all

Hi, I have a Digium B410P 4-port BRI card. I installed misdn 1.1.3 with hfcmulti driver and misdnuser 1.1.3. I configured the card "correctly" as misdnportinfo reports: # misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) -> Interface is Poin-To-Point. -> Protocol: DSS1 (Euro ISDN) -> childcnt: 2 -------- Port 2: TE-mode BRI S/T interface line (for

Just to add.... P[ 1] Transmitting 128 samples 2 misdn P[ 1] writing 128 bytes 2 asterisk P[ 1] Sending :160 bytes 2 MISDN P[ 0] misdn_jb_fill: written:160 | Buffer status:256 p:861fee0 P[ 0] misdn_jb_empty: read:128 | Buffer status:128 p:861fee0 P[ 1] Transmitting 128 samples 2 misdn P[ 1] writing 128 bytes 2 asterisk P[ 1] PH_CONTROL: channel:1 oad2:07nnnnnnnnn dad0:820055 P[ 1] --> DTMF

Hi, I've been able to make make install the Zaptel drivers (1.2). I'm using a b410p so I executed the following command make b410p. I tried this on multiple machines, but it always failes: root@asterisk:/usr/src/zaptel-1.2.11# make b410p [ -f misdn-b410p.tar.bz ] || wget ftp://ftp.digium.com/pub/zaptel/b410p/misdn-b410p.tar.gz --23:59:54--

Hi, I'm installing Asterisk on Ubuntu 6.10 When I first compiled the zaptel package I used: make clean make make install So far so good, but the following command failed: make b410p I did some digging on google and found a guide on how to install it manually, but the result was the same. I got these files ftp.digium.com/pub/telephony/zaptel/b410p/misdn-b410p.tar.gz

Hi, I'm using a 4-port BRI card (b410p) to make and receive calls (via chan_misdn): http://www.digium.com/en/products/digital/b410p.php This card supposedly has hardware echo cancellation. How can I check that echo cancellation is actually ON (taps, etc) on a given misdn channel (like with the "zap show channel X" command). "misdn show channel X" doesn't seem to show

Hi. Using Asterisk 1.4.13 running on Ubuntu 7.04 with Intel CPU: 1) Not being able to build mISDN on Ubuntu using "make b410p" I have used mISDN-1_1_7 which seems to work ok. QUESTION: Should I expect this version of mISDN to work ok with these cards? Or is there a way to build using "make b410P" on Ubuntu? (make force does not help at all) 2) In some of our installations

The DAHDI docs actually include the 'steps' that used to be in Zaptel's 'make b410p'. These steps involve downloading and compiling mISDN. Why re-invent the wheel? Just a thought :-). As for the 100ohm termination bit - it's simply changing a couple of dip switches on the b410p card (as described in the manual). Andy -----Original Message----- From:

Hi, I'd like to know what's the most "popular" method for automatic fax/voice detection for incoming calls on mISDN cards such as the B410P (hfcmulti). I'm running: kernel 2.6.17 misdn 1.1.3 asterisk 1.4.21.2 B410P card I'm using iaxmodem and hylafax with asterisk (the setup works for zap channels). I've used the following options in /etc/asterisk/misdn.conf:

Hi all! Sorry for my poor english, i'm italian. I installed Digium B410P on my asterisk server. I followed the official installation instructions found on digium site. These instruction, in my opinion, are not clear, so i tried with other ways (found on the trixbox site). I found this: http://www.trixbox.org/forums/trixbox-forums/trunks/howto-install-script-digium-b410p Now i can receive

Hi, I have two Asterisk systems that hang once every 4-6 days (more or less). One has * 1.2.31.1 and the other 1.4.26.2. The last system collapsed today and I saw several messages looping endlessly on screen: hfcmulti_rx no memory for rx_skb alloc_stack_skb(303,110): no skb size During this time the server is completely down (no ping). A forced reboot is necessary (very ugly situation in

Dear all, I tried everything to make my Digium B410P card working. I'm using Trixbox 2 and I recompiled Zaptel, Asterisk and did make b410p. Everything goes well but at the end I cannot use the card. I don't think the card is broken as in some trials in the past I saw the red blinking lights. If I put dmesg | grep Digium I cannot see anything and in asterisk cli I

Hi i've installed this software: ******************** SOFTWARE mISDN-1_1_7 mISDNuser-1_1_7 Asterisk-1.4.15 ******************** SOFTWARE misdn is correctly loaded by misdn-inist start Here there is the misdn.conf (copied from an existing and working installation with Asterisk 1.2.x and one BN8S0) ******************** MISDN.CONF [general] misdn_init=/etc/misdn-init.conf debug=0 bridging=no