similar to: anoyingly answers already in use pstn line

I am trying to setup a simple pstn gateway using Asterisk and a X100p card. I have got everything installed using Redhat 9 and am able to load Asterisk. I also configured sip and I am able to connect to the asterisk gateway with Xlite on the windows side. I am able to dial 1000 and get the welcome message. What I am NOT able to do is dial a seven digit local or 10 digit long distance number and

Hi all, With a great help from Richard Alexander (thanks Richard!) I have now a functional CallerID on my X100P. This is what I have done: - update to the latest CVS (as today at 5:00pm GMT) - modify the callerid.c file in the asterisk source like that. original : /* MDMF */ /* Go through each element and process */

Hi all is there any way how can I simulate PSTN tone on asterisk. I

I did a cvs update this afternoon and since then asterisk doesn't seem to clean up the channels after they hangup. This has been working perfectly for quite some time previously... I do a show channels and it shows the channels still up. The only way out is to kill and restart asterisk.... I am frantically trying to would out how to get a non-current CVS copy of the source and get it back

can somebody that has these hardwares(X101P and S400P) working on his asterisk system please assist.................. you can send the solution to austino@skannet.com..... the error message is what i have below. ---------- Forwarded message ---------- Date: Thu, 1 May 2003 21:01:21 +0100 (WAT) From: austino@skannet.com To: asterisk-user@lists.digium.com Subject: Error working with X101P and

Hi Please help! I have one X101P and TDM400P in my asterisk Box When i make a call from * to PSTN, everything goes Ok, When the PSTN hangups or * hangups, the busy tone is detected and * disconnects the channel without problems. The problem occurs when the call comes from PSTN. When * hangups, the other end (at pstn) does not hangup, it only presents silence. Please tell me how to solve this

Wow ! No reply... May be I must talk about X100P instead of X101P ? Is someone has yet encountered this kind of "no sound" problem when bridging two FXO lines like this (first as input, second as output) ? Any idea ? TIA. Best Regards, Francois BERGERET, France. ----- Original Message ----- From: "Francois BERGERET" <f6hqz-m@hamwlan.net> To: "Asterisk Users

When x101p clone receive ring signal from phone line, my voip phone start ringing. But, if caller hang-up at some time, phone continues to ringing 10 second more. How can I shorten that time? Pause betwen incoming rings on my phone line is 4s, so when x101p clone (wcfxo driver) do not receive next ring signal after 4.5 sec, call should be consider as ended. What should I change to set that time

I'm looking to get an x100p off ebay and am not particularly familar with the "life cycle" of the card.. An "Authentic X100P" listing has a buy it now of $29.95 and says There are 3 types of cards Asterisk would recognize: *Screenshots from the official, original driver install Cheap "OEM X100P","Clones", "Compatibles", Knock-Offs

I'm looking to acquire another FXS module -- either the TDM400P daughter module or USB S100U is fine. I'll happily buy from Digium, but thought I would give the folks here an opportunity to recycle any extra hardware :-). Please contact me if you have one to sell. Thanks! -- David

Hi, I have a X101P card and am running Asterisk SVN-trunk-r226890. The X101P card seems to be identified properly: debian:/usr/src/dahdi-tools# dahdi_hardware pci:0000:01:01.0 wcfxo+ e159:0001 Wildcard X101P debian:/usr/src/dahdi-tools# dahdi_cfg -vv DAHDI Tools Version - SVN-trunk-r7409 DAHDI Version: SVN-trunk-r7445 Echo Canceller(s): MG2 Configuration ======================

We are running asterisk with a single POTS line for local calls and a voip line for long distance. Whenever we receive a call on the POTS line it is more than likely, but not always, going to have significant distracting echo. In addition to that there is occasional heavy crackle or static. I have tried to follow the guidelines at :

I am finding that I have to increase the txgain in zapata.conf to 8 when my X101P is connected to my BT phone line, otherwise people can hardly hear me. This then gives echo issues. Do other people have the same problem on BT lines. I was wondering if I should give BT a call and get them to increase the gain on the line. Strange though as the rxgain is OK and I don't have this problem with

Has anyone been able to sucessfully use 2-4 X101P clones with Asterisk on a single system ? I'm using one Encore MD 3200 modem sucessfully, alongside a TDM400P (3 FXS, 1 FXO) and would like to be able to use up to 4 X101P on a single system. In most cases I'll have 2 or 3 instead. I understand all the issues with interrupt sharing and PC motherboard quality. Just need to know if any

Hi, I've found that neither Michael Manousos patch nor ztdummy driver do not fix musiconhold sound interruption problem up to acceptable quality level. Sound is choppy here anyway. It is my understanding (please correct me if I'm wrong) that if I have a Digium card in my asterisk machine, these problems should be gone 'cause those cards provide some reliable timing. So I have no

I am still having unacceptable echo on my X101P and twidling with the rx/tx gain levels and echo settings appears to have no discernable effect. Some questions for those who may have more significant electrical engineering background than I. 1. This impedance match thing ... will it affect this solution having other phones in parallel with the X101P? This is done so that I can test while not

hi, i am having callerid problems with *. i have the callerid from my telco and it shows up in my normal phone when i connect it directly to the line but if i connect the same phone thru * server the callerid is not shown. i am using X101p and tdm400p. i have everything defined in my zapata.conf well and fine. i finally came to conclusion that this might have happened due to the registration of

Hi, I've just added an X101P FXO card to my asterisk machine. The card is detected ok but zttool always shows it in a RED alarm state, which I understand means that it doesn't detect the line. I've connected the card via the line socket to my analogue line using the cable that came with the card (and have also tried other cables too) but I always get a RED alarm. I'm located in

X101P with Ambient md3200 chip on it, with the zaptel wcfxo driver.... Just an indication of how many people have got this to work would be useful. Cheers Mark.

Juan, I am running a Calling Card application on a Dell PowerEdge 2850 with Asterisk 1.0.7. Recording conversations I have seen on my server causes the processors to burn more than necessary so I would recommend what William from Signate recommended: " Consider saving recorded calls in a database on a separate server. It will be simpler to build a retrieval interface that does not