similar to: Polycom 330 not dialing 4 digit extensions beginning with 11xx

Hi all. I just installed bunch of IP450's and everything went well and my customer is happy.... except that they are unable to transfer calls to other extenstions. They can dial them directly just fine. However, when the user is in a call and presses the transfer soft key, they get dial tone, and start typing the extension, say 1008. But by the time they get 100 typed in, the phone tries

I'm replacing a SoundPoint IP 600 with a SoundPoint IP 650. I attempted to simply reuse the existing config files for the old phone on the new phone, but the new phone would lock up on the 4th digit when attempted to dial out certain numbers. So, I downloaded the newest firmware and config templates from Polycom, and attempted to migrate the settings. Seems I'm missing something from

Just installed Asterisk 1.2 on a brand new clean machine running RedHat 9.0. I have a TDM400 card inside. When I boot, the card seems dead. When I do: modprobe wctdm modprobe Zaptel the lights come on and all seems fine, until I reboot that is... After a reboot I have to repeat the modprobe. I shouldn't have to do a modprobe every re-boot should I? How do you get the drivers to load

Hello, I have a mixture of Polycom SP IP 500 and 300 phones. I have been reading through the administration manual to try and solve this problem, but I do not seem to be able to find the answers to my question. I figured I would ask here and see if anyone has some suggestions. The problem is kind of annoying. After dialing 4 digits, the phone seems to pause and miss the 5th digit, often

I'm running Asterisk 1.2.8 with Polycom ip501's xten softphones The only problem I'm experiencing is the following: I can't seem to get blind transfers to work with my Polycom 501 phones Either through the feature code or the soft keys. Feature code blind transfers: I set up a feature map in features.conf like this: blindxfer => # This works for all my

I'm stumped on this one and any help would be greatly appreciated. I'm just trying to get my Polycom 601 to have multiple extensions on it. For example, on line 1 I want extension 21, on line 2 I want extension 22, and on line 3 I want extension 23. Ideally I'd actually have each extension appear on 2 lines and therefore filling up all 6. I should be able to do that with the

This is a dialpaln issue. I solved the same problem recently. For 4 digit extensions you need to append the dialplan statement in the sip.cfg configuration file as follows <digitmap dialplan.digitmap="[2-9]11|0T|011xxx.T|[0-1][2-9]xxxxxxxxx|[2-9]xxxxxxxxx|[2 -9]xxxT|1xxxT" dialplan.digitmap.timeOut="3"/> Michael > I am not sure what I did but blind transfers do not

Any Polycom gurus out there? If so, I have a few config file questions. First off, does anyone have the daylight savings time rules written for this Sunday's big change? Secondly, if there any way in the config file to tell the phone not to display the number of missed calls? I don't mind it keeping the missed calls list, I just don't want that running count. Lastly, I am trying

hi there I'm setting up asterisk@home and I'm using Polycom IP 500 phones. When I call a number that has a digital receptionist (i.e. "dial 1 or such and such, dial 2 for this and that...") the Polycom doesn't seem to send the extra digits. When I try it with X-Lite things appear to work fine, so I think the problem is with the Polycom configuration. Here's some

I am having a strange problem with polycom 501 and dailing. I've read the archives and no one there specifically mentions this problem, so I thought I'd ask here. The problem is that when the user picks up the receiver or pressed new call, sometimes they will enter a number (for example 95072091234) and in the middle of the number the cursor might jump back one digit. So the call above,

Hello All, I have some Polycom IP 500 phones that I would like to have configured for direct dialing to our voice mail system. So far I have been unable to get the hard button labeled Voice Mail to connect to Asterisk without first passing through the message center prompts. I have followed all the Admin Guide instructions regarding the phones .cfg files and using

Hi All, I'm not sure if this is related directly to asterisk or not but on my Polycom 320 when I try to dial a number smaller than 4 digits I get an error on the phone saying "Enter more digits". The dial plan section is listed below. <dialplan dialplan.impossibleMatchHandling="0" dialplan.removeEndOfDial="1"> <digitmap

Calling all Polycom gurus: I am using Polycom IP601 phones with Asterisk 1.4.21.2 In all Polycom phones, I set the following in sip.cfg. <dialplan dialplan.impossibleMatchHandling="2"> </dialplan> (I leave the digitmap unchanged because I thought setting impossibleMatchHandling will ignore the bitmap) ...so that I could dial any number by entering a variable-size

via google, I found the reference regarding digit maps for the Polycom phones: http://lists.digium.com/pipermail/asterisk-users/2005-January/082884.html But I don't see any instruction for prepending digits to the number dialed. Does anyone know how to prepend a digit to the number dialed (from the Polycom side, not Asterisk)? I can do this pretty easily on a Sipura. i.e. Say I want to

I am having a problem with some Polycom 601 phones. If I dial without picking up the handset or selecting the speaker I can dial numbers that are any lenght. But if I pick up the handset or are using the speaker I can only dial numbers that are 8 digits. When I dial the 8th digit it dials immediately. Obviously this creates problems when I am dialing long distance numbers or anything that

I have a number of Polycom phones to setup with my * server. For my initial few phones I hand wrote configs. Does anyone here who uses Polycom phones have some form of management utility for automating their setup? Michael -- Michael Graves mgraves@pixelpower.com Sr. Product Specialist www.pixelpower.com Pixel Power Inc.

Sirs, According to RFC 2705 (MGCP), these are the parameters that are used in the transactions: ReturnCode, Connection-parameters <-- DeleteConnection(CallId, EndpointId, ConnectionId, [Encapsulated NotificationRequest,] [Encapsulated

Hi All, Having a rather annoying problem with the Polycom 301 phones, suspect it to be my dialplan. Basically if you lift the receiver off the handset and dial a number, it will not let you dial a number longer than 10 digits (Can see this being acceptable in US, but in UK its a right pain). As soon as the 10th digit is entered, it starts to dial and the number is invalid. If the phone is left

When I do remote form submits through jQuery .submit() why do I sometimes have to refresh the page manually to see the results? My jQuery handler is very simple: $("#vote_yes").click(function() { $("#approval").val(true) $(".edit_vote").submit() }); And the link that leverages this bit of code is as follows: <%= link_to("Vote

Dear All Can you please do me favor and let me know what is the problem with my Asterisk call parking as it is not functioning correctly on my Asterisk ? Please find attached my "features.conf" . According to my configuration , the subscriber needs to press hash (pound) key and dial 700 to initiate the transfer . We tried but it didn't get through on our Asterisk . Can you please let