similar to: Zapata Tormenta 2

Hi All, I'm having a bit of a time getting my Tormenta 2 card to actually be seen by the system. Whenever I modprobe, the kernel spits out the following (in addition to the "insmod tor2 failed" messages): Invalid Xilinx 8 bit Base resource Registered Tormenta2 PCI Of course, the module says that its registered a Tormenta2 card, but it unloads the driver and frees related

Hello,every one! I want to fabric a piece of Tormenta ISA E1 card for study. But the from http://www.zapatatelephony.org is all about Tormenta ISA T1 card. I want to know if they are using the same chips or something different bettween them. Thanks. john

Hi everybody, I need to know about sound quailty issues from those who have experience with Tormenta2 PRI Interface. Also how to make it work with new versions of Asterisk and Zaptel. And also suggestion if it is a good idea to switch to some newer card from Sangoma or Digium, or Tormenta should work fine. I have sound breaking many times a day over the trunks. Server is AMD Athlon 2.4 GHz with

Hello guys! I hope you bare with yet another newbie on the list! :-) I am trying to setup an asterisk installation in between a Siemens HiPath 3800 and my local carrier (Telefonica/Brazil). Both running R2. ISDN is not an option on the carrier. :-( I could apparently setup both E1s just fine according to zttool (both OK with no alarms) but, and this is where it starts to get

Hi there, my * has no Zaptel or Tormenta hardware at all, also no ztdummy. However dmesg is full of Zapata Telephony Interface Registered on major 196 No ISA tormenta card found at d0000 Zapata Telephony Interface Unloaded and /var/log/messages shows tons of this: Nov 25 21:28:28 localhost kernel: Zapata Telephony Interface Registered on major 196 Nov 25 21:28:28 localhost kernel: No ISA

Hi list, I have a asterisk box with an E400P that was running ok until last week. The machine just stop responding and after a reboot, the module (tor2) doesn't load anymore. anyone could help? regards Eduardo modprobe returns this: asterix:~# modprobe tor2 Zapata Telephony Interface Registered on major 196 Detected Tormenta 2 Quad T1/PRI or E1/PRA at 0xfe121800/0xfe121000 irq 7

Hello: I have a "Tormenta ISA Card, Rev. A" and wanted to know if somebody knows like integrating it with Asterisk. It would thank for any information on the matter. Thanks!!!! -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040907/df5cccd6/attachment.htm

Hi, I have just begun working with TDMoE running between 2 fiber nics the dynamic span works great. In my main asterisk box's startup file I just 'modprobe tor2', then start asterisk. The zaptel, ztdynamic & ztd-eth modules all load by themselves when tor2 is loaded. If I stop asterisk then 'modprobe -r tor2' the tor2 module is removed but the other three remain. If I

Hi, > While I was surfing the net last week, > I found a link for "open source" pci telco cards. > I'm not sure if it were isdn or analog related. > The layout an all the stuff was free downloadable, so that > you can build your own cards. > Does anybody have the link? you're probably talking about the Zapata Telephony Project and their

(I'm producing a writeup on all the things one run into building an * box. Which after a couple of boxes is showing up aplenty.) So this uses the working h/w and config's from another box. All I do is build in a new computer. Loading the modules I got: __________________________________________________ Zaptel Configuration ====================== Channel map: Channel 01: FXS

Whatever happened to the Zapatatelephony project? The last information there is from 2001 and a lot of new cards have been released since. Has GNU hardware development completely stopped?

Just installed Asterisk 1.2 on a brand new clean machine running RedHat 9.0. I have a TDM400 card inside. When I boot, the card seems dead. When I do: modprobe wctdm modprobe Zaptel the lights come on and all seems fine, until I reboot that is... After a reboot I have to repeat the modprobe. I shouldn't have to do a modprobe every re-boot should I? How do you get the drivers to load

Hello- As part of the asterisk build/installation instructions it mentions that the zaptel drivers should be built and configured first. My question is whether they are required at all, in the case of a system with no hardware cards at all (as is the situation in my case). With them loaded I continually get the following message on my console (server not asterisk): Zapata Telephony Interface

Good day everyone, A Solution now exists for those of you still looking for the first model of Quad T1/E1 Interface Cards - the T400P and E400P. The T400P and E400P were manufactured by Digium until a few months ago, and were designed and released under the GNU Public License as the Tormenta II by Zapata Telephony. Varion, Inc. is now in full production manufacturing these boards. With the

Looking at my log file I found the following error: May 2 12:00:45 debian kernel: Zapata Telephony Interface Registered on major 196 May 2 12:00:45 debian kernel: No ISA tormenta card found at d0000 May 2 12:00:45 debian kernel: Zapata Telephony Interface Unloaded May 2 12:00:45 debian insmod: /lib/modules/2.4.20-8smp/misc/torisa.o: init_module: Input/output error May 2 12:00:45 debian

Greetings, I have a quad port Tormenta 2 PCI card (uses the tor2 driver), which I have been successfully using for some time on an older, power-hungry Intel machine. I recently moved it to a newer machine with an Intel Atom D510 CPU in an effort to save on energy costs, but I cannot seem to get it to work there. Both machines are running Ubuntu 13.10 x64, with DAHDI support coming from the

Does anybody have any tuning tips for a samba 3.0.23 server that is acting as a PDC with ldap backend and file server. The problem I'm having is a certain program runs in XP workstations that accesses files on one of the shares, it apparently opens lots of files and is constantly making changes to them. When I run top, I see each smbd process for each workstations is consuming about

Hello all After install the Asterisk, setup the configuration file in the sip.conf and extensions.conf and type "asterisk" with start program. I don't have line card yet. But I found following error in the /var/log/messages. localhost insmod: /lib/modules/2.4.18-5/misc/torisa.o: init_module: Input/output error localhost insmod: /lib/modules/2.4.18-5/misc/torisa.o: insmod

Hi everyone (Mark, Jim). I am new to the list but thanks to both Mark and Jim, I have being using "asterisk" since summer 2001. I am just updating my version that was a year old. Yes, I know, I got busy with other things like paying bills so I don't have to sleep with the dog anymore. Anyway, one of the frustrations I have been dealing with (keep in mind that my version of