similar to: Can call in but cannot call out (CHANUNAVAIL): TE410 + Asterisk 1.4.13 + Zaptel 1.4.6 + Libpri 1.4.2

I just managed to put in a TE410 card in an Asterisk box to work with OnRamp 20(E1 downunder). I am able to dial in but was not able to dial out. Can anyone offer me some advice please? In my extensions.conf, I just put in: [default] ... exten => 0,1,Dial(Zap/g1) and I get this on the console when I dialled 0. -- Executing [0 at default:1] Dial("SIP/5166-b76004f8",

Hello I've been googling for this message, but can't find why Asterisk sends a warning. The configuration files look similar to http://www.voip-info.org/wiki/index.php?page=Asterisk+config+zapata.conf.sample It's a TDM card with just one FXO module on it, and I connected an RJ11 cable to it from the wall plug: # cat /etc/zaptel.conf fxsks=1 loadzone=fr defaultzone=fr # ztcfg -vv

Hi, am building the latest version of Asterisk (1.4.13) on a self-build Linux host (based on LFS-6.3). Version 1.4.12 built installed and worked fine. Last night I upgraded the kernel to 2.6.23 and rebuilt the zaptel driver package 1.4.5.1 against it. That seemed to build and install O.K. too. I dl'd the 1.4.13 source tarball and tried to build that: ./configure ran O.k. 'make

I have been trying for some time now to make the hook flash work on the FXS port. I am using Asterisk 1.4.10.1 with zaptel 1.4.4. When I "manually" flash the hook I can manage to find the duration to put a call on hold. However when pushing the flash button it never works. The phone's flashtime seems to be too short. I tried to set a shorter flashtime in the zapata.conf file, but it

install asterisk with x100p clone; the problem is that call me and hangup but the interface zap not detect the hangup and the line open. the error is : The 'reload' command is deprecated and will be removed in a future release. Please use 'module reload' instead. -- Reloading module 'chan_zap.so' (Zapata Telephony) == Parsing '/etc/asterisk/zapata.conf':

Hi, I'm trying to bring up two PRIs from qwest with asterisk and dahdi. I'm using an OpenVox D410E and the drivers are loaded. My system.conf looks like this: # Span 1: TE4/0/1 "T4XXP (PCI) Card 0 Span 1" B8ZS/ESF RED span=1,2,0,esf,b8zs bchan=1-24 # Span 2: TE4/0/2 "T4XXP (PCI) Card 0 Span 2" (MASTER) B8ZS/ESF RED span=2,1,0,esf,b8zs bchan=25-47 dchan=48 These

Dear members of the list, I have difficulties to obtain sync with a Digium TE420 PCI Express For four entries E1, In my case I am with only 3 E1s available to configure. The telephony operator is BrasilTelecom and Signaling is R2 Digital. The information I have is that are E1s with 32 channels, not have sure. My settings Have been based on the link reference:

I keep getting a red alarm when trying to setup asterisk to use my TE420B EC. I only have a blank context setup in my extensions.conf as I haven't started to config that until I can clear this red alarm. I don't have physical access to the server, so I can't go reseat the modules/card/ethernet cable, though I have hands on location that have done this a couple times

Hi Guys I'm configuring a TE212P card and have the following two entries in my /etc/asterisk/zapata.conf switchtype=dms100 signalling=pri_cpe When I reload asterisk I get the following messages: > -- Reloading module 'chan_zap.so' (Zapata Telephony) > == Parsing '/etc/asterisk/zapata.conf': Found > [Mar 30 17:48:42] WARNING[2985]: chan_zap.c:11072

I just noticed that the new TE410 only supports 3.3v PCI. How do you know if it will work in your machine? It's not something commonly listed in your motherboard specs.... I was thinking about getting one for an Athlon 750 that is a spare box I'm doing testing on... (Original SlotA) -G

I'm trying to install a TE410P this is what happens with compiled zaptel 1.0.9, 1.2-beta and 1.0.9 from http://updates.xorcom.com/iso/ this is my zaptel.conf (checked with the provider the values): span=1,1,0,ccs,hdb3,crc4 bchan=1-15,17-31 dchan=16 loadzone=it defaultzone=it then I modprobe wct4xxp debug=1 t1e1override=15 and the kernel says : Sep 30 16:12:40 localhost kernel: Zapata

Hi, I'm trying to connect a PC with a TE410P to an E1/IP equipment. Unfortunately I keep getting a yellow alarm from zaptel (in zttool) and a Loss of Framing alarm on the remote equipment. The E1/IP is connected on the other side to a PRI interface on a GSM MSC. I have configured the span as: span=1,1,0,ccs,hdb3 (also tried span=1,0,0,ccs,hdb3) and the channels as: bchan=1-15,17-31

Hello List Just want to check if anybody else is having this problem. Every time the PRI connections are disconnected, the card freezes, and I have to reload the driver, to make it work again. We are very seriously considering switching to Sangoma at this moment, due to this and other problems, but I want to know if there is a solution, and to make sure it isn't asterisk that's freezing

If I remove the eco cancellation module from a TE411P card, will it work as a plain TE410P? -- Carlos Chavez Prats Director de Tecnolog?a Telecomunicaciones Abiertas de M?xico S.A. de C.V. Tel: +52-55-91169161 Ext 2001 -------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: application/pgp-signature Size: 191 bytes Desc: This is a digitally signed

Hello, I would like to have some comparison between E1 cards from Digium and those from Eicon for a VOIP - ISDN Gateway. How does they compare on the echo cancel point of view? Is the echocancellation code for E400 good enough for production environment? Best regards, Daniel -- Daniel ANDRE (mailto:dandre@iris-tech.fr) IRIS Technologies - http://www.iris-tech.com Serveur kwartz -

Hi, I am about to pull my hair out after trying to get our PRI up and working. We are switching from a Cisco gateway to an Asterisk box which provides the 23 phone lines for our office. So, because the Cisco gateway is working I can assume I have all the settings right (b8zs, esf, dms100, etc) and the PRI is live (because we are switching over). When dialing from PSTN, I get busy signal. When

We are located in Belgium and just ordered a PRA line, the telco asked the following questions : - 120 or 75 ohm ? - Support for CRC4 yes/no ? - B channels in 2 way ? We will buy a digium card but which one should we buy ? could anybody help me with this ? Thank you Michael Sorry for the previous html mail DISCLAIMER: The content of this e-mail message does not constitute a commitment

This afternoon I finally figured out more with regarding to a strange clock-slip problem we have on our asterisk box. We have two TE410s, in E1 mode: TE410P version c01a009b They have their own interrupts: 66: 781648298 783747388 IO-APIC-level t4xxp 233: 253890977 1311504670 IO-APIC-level t4xxp They have their full 31 channels: span=3,0,0,ccs,hdb3,crc4 bchan=63-77,79-93 dchan=78

Hi anyone have a idea for debug my digium TE405P card ? My zaptel.conf: span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone = fr defaultzone = fr My Zapata.conf: [channels] language=fr context=from-E1 switchtype = euroisdn pridialplan = unknown signalling = pri_cpe usecallerid=yes hidecallerid=no callwaiting=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes

I've done a decent size update of the OpenSSH portable from the upstream tree. There is an AES upgrade that needs to take place, but I need people to test and tell me what endedness changes need to be applied (if any). Attached is the patch. It is geared towards the latter snapshots..Unsure how it will patch (if at all) against 2.9pX series. Thanks. - Ben "This is dark day in