similar to: Problems with setting up Zaptel

Hi, I am using asterisk 1.4.28 with freepbx and Wildcard TDM410P card. Everything is working fine except the caller ID of incoming call from PSTN line. The phone display is showing "Unknown" when there is an incoming call. *My log file showing this while an incoming call on PSTN line:* tail -f /var/log/asterisk/full [Dec 30 06:36:16] DEBUG[2559] dsp.c: dsp busy pattern set to 0,0

Hello... I have a big problem with asterisk. Every time i make a call asterisk does not bridge the zap channels. The zap channel from which i'm calling remains in state:ring and applicaton:dial and the zap channel with the external line configured remains in state:dialling an Application:AppDial. Zap/20-1 agentie s 1 Dialing AppDial (Outgoing Line) 09399 (None) Zap/9-1 int_omg 09399 5 Ring

(Sorry of this appears in the list twice, but I wasn't sure if it was blocked or not) Hi there, I'm having a problem with my TDM-400P which has been working like a charm up until very recently. It started to fail last week, and so I was hoping someone could illuminate me with some information as to why. Its configuration is as follows: ------------ FXS (green) module is in position 1,

Hello, I've one astribank with 8 FXO unit and 8 pstn lines connected to the astribank. When I receive calls on my ipphone I get always Unknown callerid. It's is possible to receive the callerid from the lines on the astribank unit? This is my config: [channels] language=es context=from-zaptel signalling=fxs_ks ;rxwink=300 usecallerid=yes callerid=asreceived ;cidsignalling=bell

Hi, I've got a problem with my asterisk set up which has been going on for a while (months). I'm currently running 1.2.7.1 on a gentoo box with the topology below: +-----+ PSTN ---------+ * +------------- Service Provider (wctdm400p) +-+-+-+ IAX | | | | FXS --+ +-- SIP (cisco 7940)

Hi, I am using TDM400 card with 3 fxs and 1 fxo. I am struggling to detect hangup tone or disconnect supervision tone from my CO. I attached the recorded wav file which contains my telco's disconnect supervision. I am using , asterisk-1.4.33.1 dahdi-linux-complete-2.3.0.1+ 2.3.0 OS => Debian-lenny 5 users.conf ------------- [trunk_1] trunkname = pstn ; GUI

Hi, I am using asterisknow 1.5.0 and Wildcard TDM410P card. Everything is working fine except the caller ID of incoming call from PSTN line. The phone display is showing "Unknown" when there is an incoming call. I think the same problem listed here: https://issues.asterisk.org/view.php?id=6683 There is one patch on this link but i don't know how to apply patch on asterisknow.

i belong to india. i am making pbx using sangoma fxo card. i want that when ever call comes to my PSTN line i should see the no from where call is coming. so i have to configures chan_dahdi.conf according to my region. i checked dahdi.conf and in that they have mentioned for india

My outgoing FXO calls are answered but have no audio in either direction if I have callprogress=no in chan_dahdi.conf. If I change to callprogress=yes then the audio returns. My chan_dahdi.conf file is listed below. Can anyone point-out why callprogress=no isn't working? #cat /tmp/a [trunkgroups] [channels] language=en context=incoming toneduration=40 ;usedistinctiveringdetection=yes

Hi list First of all could you please explain loop-start and ground-start for me? What are they used for? Next, I have the following configurations: dahdi-channels.conf : context=pstn-channels signalling=fxs_ks channel=>130 context=phone-channels signalling=fxo_ks channel=>127 chan_dahdi.conf : [channels] cidsignalling=dtmf cidstart=dtmf signalling=fxo_ls pulsedial=no

Can anyone suggest where I might begin looking for an answer please? I have just installed a TDM400P (2x FXS and 1x FXO modules installed) The first problem is that it does not seem to be able to detect if the remote party has hung up when a call comes through on the FXO. For example, if someone calls in, and then hangs up at any time after it starts ringing, Asterisk carries on as though the

Dear All I have a problem with a TDM400 card with 4 x FXS modules. The card carries extensions only and there are no incoming lines. I can make a call to the extension on this card with no problems. However, when I try and call out I just get a busy signal. I also get an error message (as shown at the bottom). Is this a problem? Configs below: [root at asterisk etc]# more zaptel.conf

Has anyone got a sensible zaptel.conf and zapata.conf for 2 TDM400P's working with UK set-up. They're set-up with 7 analogue phones and 1 PSTN port. Currently zaptel.conf has fxoks=1-7 fxsks=8 loadzone=uk defaultzone=uk It's really zapata.conf that would be useful. Currently using the zaptel/asterisk that comes with Ubuntu (latest) which needed a bit of tweaking (1.2.16), but could

I am running Asterisk 1.6.2.17.2 with a Openvox A400 card with 2FXO/2FXS modules. I'm trying to set-up things to route analog fax calls from a FXO port to an analog fax machine on a FXS port on the same card. Outgoing faxes work just fine. But incoming faces are routed to the right DAHDI extension, but the call dropped right as the fax machine rings for the first time. The fax machine

Hey all, I recently noticed that DTMF caller-ID was implemented in CVS, so I requested the service from my telco (the Dutch KPN) and tried to get it going in Asterisk (current CVS), without success so far. This system has 1 X100P, 2 TDM400P's with 4 FXS-modules each and 2 HFC-PCI ISDN-cards (zaphfc-driver) in it. The analog line I'm trying to get caller-ID working on is obviously on the

Today I received a TDM11B (1 FXO and 1 FXS) and got it installed just fine. I bought the card mainly to get caller ID to work properly in Sweden, and that works just fine. However, if the called or calling party hangs up after I hangup my SIP channel, polarity CID detection kicks in and dials a couple of signals to my incoming context. This happens with Asterisk 1.0.6 and CVS-HEAD. I have tried

Greetings listers. I'm running asterisk 1.4.21.2 on SUSE 11.0 using Polycom 501 phones. My outgoing connections are Zapata using a TDM401P. For the most part I can make and receive calls fine except for these 3 issues: 1. When I call an external conference, the call never bridges and hangs up after 60-90 seconds. 2. When I call another number there is a

Hi everyone, Sometimes i am having problems with Zap channels on asterisk 1.2 (Disc-OS 1.1), after some calls, the channel continues in use, even after hanging the call up, then i need to run the "soft hangup Zap/<zapchannel>" in the asterisk CLI to release the channel. Here is my zapata.conf: [trunkgroups] [channels] language=pt_BR context=default usecallerid=yes

I'm testing a TDM400P with FXO module to receive incoming calls from an analogue line and send it to a SIP device. To recieve callerid, I need to use cidsignalling=dtmf and cidstart=polarity. The problem is that when a call is finished, the TDM400P seems to require about 20 seconds to prepare for the next incoming call. If a new call comes in within 20 seconds after the previous call was

Hello gang, We just got MaBell to turn on our callerid. I tested the capability with a southwest bell box and a plain phone, so I know the line is sending the signal. I'm running Asterisk SVN-branch-1.4-r204834 using a TDM400P card. Here is my dahdi_cfg -vv output: dahdi_cfg -vv DAHDI Tools Version - 2.1.0.2 DAHDI Version: 2.1.0.3 Echo Canceller(s): MG2