similar to: [Zaptel] Checking that TDM card works?

Hello I am (attempting) to run the astlinux version of Asterisk on a VIA embedded platform. I have a TDM04B and pretty sure zaptel.conf and zapata.conf setup OK. They worked fine with same card in traditional PC anyway. I think need the module wcfxs for a Digium TDM04B card. Is this module not part of astlinux? Do I need to download it? Or is it in opt? I see wctdm - but think that is

Hi all i need urgent help our entire switchboard is down only 5 days after it came up. this is the second time this has happened and i am thinking that asterisk is not worth the trouble it gives. mostly it runs without hassle. but around 2 weeks ago during the test phase we rebooted the machine and did the normal modprobes and this error popped up. coming back to work after the weekend the

Hi All, I have the problem setting up TDM22B card. Steps what I have followed are: [1] compiled zaptel-1.0.9.2 & installed the same. [2] modprobe wcfxo /lib/modules/2.4.20-8/misc/wcfxo.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg

I am having trouble with chan_zap.so not loading. When I load it from modules.conf, Asterisk bails out without any error message. When I load it from the console, it just says "Unable to load module chan_zap.so" no matter what verbose level I am using. dmesg says: Zaptel Version: 1.4.4 Zaptel Echo Canceller: MG2 Freshmaker version: 73 Freshmaker passed register test Module 0:

Hi All I've bought a TDM400P and need some help with configuration. Can you tell me what to do ? I've tried to install and the message below has appeared: [root@voip asterisk]# modprobe zaptel [root@voip asterisk]# modprobe wcfxo /lib/modules/2.4.22-1.2115.nptl/misc/wcfxo.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid

Hello, I have found a "bug", I think in the way TDM400P cards handle FXO interface disconnect/re-connect problems. Normally I do keep all the wires connected from my CO / PABX quite securely, but I had a need to re-route the cable from one side of the desk to another, and I simply disconnected the RJ-45 connector and plugged it back in. THIS PROMPTLY RESULTED IN VERY VERY SCRATCHY AUDIO

hi you, I'm having problem with voice quality on my trixbox using TDM2400B.The trixbox is connected via 20 FXO ports on a TDM2400 with the hardware echo cancel module. Echo cancel almost works, but the users hear what they describe as a 'background crackle/buzz' coming back when they talk. anyone have the same problem? pls help me. thanks a lot. my trixbox and config

/bin/sh: -c: line 0: syntax error near unexpected token `;' /bin/sh: -c: line 0: `if [ -n "" ]; then if [ -f ]; then mv -f .bak ; fi; cat .bak | grep -v "alias char-major-250" | grep -v "post-install torisa /sbin/ztcfg" | grep -v "post-install wcfxsusb /sbin/ztcfg" | grep -v "alias wctdm" | grep -v "post-install wctdm

I have read thru what other users have tried in this list when they have experienced seemingly similar issues to what I have, without success. I suspect there might be an issue regarding both the X100P and TDM04b cards being used in an Intel SE7525GP2 motherboard, as I had to even wait for a BIOS update from Intel in order to utilize my 3ware 9500 SATA raid controller on it (3ware Kb -->

I go to my Zaptel 1.4.0 folder and run ./configure; make linux26; make install and I don't see any errors. This is out of my modprobe.conf: install tor2 /sbin/modprobe --ignore-install tor2 && /sbin/ztcfg install torisa /sbin/modprobe --ignore-install torisa && /sbin/ztcfg install wcusb /sbin/modprobe --ignore-install wcusb && /sbin/ztcfg install wcfxo

I'm trying to use a Xorcom Astribank wth Ubuntu 8.04, but got no success. I can see the channel bank with lsusb, but when I tried to use zaptel_hardware, or when I try the /etc/init.d/script, they don't see my Channel Bank. I compiled the latest Zaptel 1.4.10, with Astribank's dependecies, fxload and libusb-dev. Anyone have a similiar experience ? Best Regards, -- Guilherme Loch G?es

Hi, using Sangoma drivers: - doing 'lsmod', I see: zaptel ... wanpipe,wctdm24xxp,wctdm,wcfxo,wcte11xp,wct1xxp,wct4xxp,tor2 I'd like to avoid loading all these modules. What have I to do? - do I need to have 'zaptel' startup script under /etc/init.d ? Thanks -- Domenico Viggiani

Hi people, I'm having some problem when I reboot my machine. Every time that I reboot the system, the zaptel changes the order loading of the cards. I have 3 cards (wcte11xp, wctdm and wcfxo). So, my configs in the zaptel.conf will be always wrong, because I change the config for a order loading, and when I reboot its change! I tryed to see the config in /etc/udev/ but I think its right,

Hello I setup Asterisk@Home with purely VoIP and it worked fine. I then added an X100P card so I could call out / take inbound calls via PSTN and that went fine. But I have just added a TDM400P card (specifically a TDM30B) and now problems. Here is some of the output. Any ideas on what I should be looking at next? When I run genzaptelconf -s -d I get lots of erors on screen - bit I can

Hi, I'm cutting my teeth setting up a home asterisk server, but having some trouble getting Zaptel to recognize a X100P clone PCI (Motorola SM56 which should work according to various wiki's). What struck me was that the "/proc/interrupts" do not include IRQ 11 as the "lpcpi -v" is reporting. Am I missing something fundamental here? Any hint is greatly

Hello! I have problems compiling zaptel (tried 1.2.11, 1.2.10 and 1.4.0-beta2 -- all give the same error) with 2.6.19 kernel CC [M] /home/roman/install/asterisk/zaptel-1.4.0-beta2/xpp/card_fxo.o In file included from /home/roman/install/asterisk/zaptel-1.4.0-beta2/xpp/xpd.h:26, from /home/roman/install/asterisk/zaptel-1.4.0-beta2/xpp/card_fxo.c:28:

Hi, I got my TDM11B and am trying to get it to work on my PC. However, I'm having difficulty getting the wcfxs driver to load. I've Googled this problem, and while there are others who have ran into the same problem, none of the solutions work for me. I would very much appreciate it if you could suggest things I could try to resolve this problem. Details follow. The PC is somewhat

I originally built my Asterisk server without installing the Zaptel package as it was going to be a purely SIP based system. However when I went to setup conferencing using meetme I found out that app_meetme is dependant on the ztdummy for timing. I have now installed the zaptel package and I believe the ztdummy module is loading ok [root@astro asterisk-1.4.0-beta2]# lsmod Module

Hi all, What hell hapen here? asterisk:/etc/asterisk# /etc/init.d/dahdi startLoading DAHDI hardware modules:FATAL: Error inserting dahdi (/lib/modules/2.6.26-2-686/dahdi/dahdi.ko): Device or resource busy wct4xxp: done wcte12xp: done wct1xxp: done wcte11xp: done wctdm24xxp: done wcfxo: done wctdm: done wcb4xxp: error wctc4xxp: done xpp_usb: doneError: missing /dev/dahdi! When

I know, I know, check the archives but I can't find an answer since the new cards are well, NEW! I understand the whole issue of expandability and flexibility of using a T1 card and an Adtran 750. FXO or FXS, you mix and match. With the new card offerings from Digium I can easily put a 4CO by 8 Station system together. Barring the extra interrupts, extra CPU Cycles of extra interfaces, is