similar to: Zap channels for HFC-S PCI card not responding

Hi list, Attempting to get an ISDN-BRI line connected using an HFC-S PCI card together with Asterisk v1.4.14 and Zaptel 1.4.7 on a Debian etch system, I find that I can't access the card's resources because the channels are always be busy. An attempt to call out results in the following CLI output: == Primary D-Channel on span 1 down == Primary D-Channel on span 2 down

Hello, The harddisk of my etch/bristuffed asterisk1.2 box finally died. I moved the cheap (1397:2bd0) HFC-S card to a squeeze host (i686) and built dahdi modules 2.3.0.1 using m-a. After zaptel->dahdi and asterisk 1.2->1.6 config adaptations, everything seems ok, except for the BRI side, unable to bring layers 1/2 up. Asterisk reports: chan_dahdi.c:12393 dahdi_pri_error: 1 Unable to

Hi list, Now that I've got my Asterisk server to recognize my HFC-PCI card, I've run into some serious problems. The first thing I noticed was this message that would show up every five seconds on the CLI: Dec 27 15:46:42 WARNING[12484]: chan_zap.c:2512 pri_find_dchan: No D-channels available! Using Primary channel 3 as D-channel anyway! == Primary D-Channel on span 1 down

Hi list, Has anyone been able to get ISDN-BRI support to work reliably on Asterisk 1.4? If so, I'd love to know how you did it (hardware, distro, kernel, modules, versions, config files). I've tried to get it to work on a Debian etch system with an HFC-PCI card and the zaptel package (v1.4.7, also from xorcom.com), but with no luck: all three channels that are created when the

Hello, I am trying to use a HFC-PCI (CCD/Billion/Asuscom 2BD0) card in TE mode to dial-in and out with ISDN. The problem is I can not get the card to dial out with a Zap channel. Dial-in is working. I am using bri-stuff 0.1.0-RC4 (but tried also RC3 and RC2k). I tried all combination of "immediate", "overlapdial", "pridialplan". I earlier also managed to dial out

Hi all, On an Asterisk/Zaptel 1.4 system, one way to gather diagnostic info is: ~# cat /proc/zaptel/* Span 1: ZTHFC1 "HFC-S PCI A Zaptel Driver card 0 [TE]" (MASTER) AMI/CCS 1 ZTHFC1/0/1 Clear (In use) 2 ZTHFC1/0/2 Clear (In use) 3 ZTHFC1/0/3 HDLCFCS (In use) Span 2: ZTHFC2 "HFC-S PCI A Zaptel Driver card 1 [TE]" AMI/CCS 4 ZTHFC2/0/1 Clear 5 ZTHFC2/0/2

Hello, I tried to connect my Siemens ISDN 4170 cordless small PBX to the asterisk with an Acer HFC isdn card but I have not seen any success. The asterisk can see the card but no success to receive or dial a call. The Siemens 4170 gives fault in all the handsets with trying to dial and does not receives anything. I have linux kernel 2.4.29, asterisk CVS-v1-0-03/12/05-17, zaphfc

Hi, I have debian etch 4.0 machine (2.6.18) with two TW-ISDN PCI (Hfc) cards. I use bristuff-0.3.0-PRE-1y-e (asterisk-1.2.17,libpri-1.2.4,zaptel-1.2.16). I also have patched zaphfc with zaphfc_0.4.0-test1_florz-13.diff.gz (I load module: insmod /usr/src/bristuff-0.3.0-PRE-1y-e/zaphfc/zaphfc.ko modes=1 debug=1). So i want to test two cards and make loop between them. So one card would be NT,

Hello, I have about 10 Asterisk PBX in production with Bristuff-0.2.0-RC8q (asterisk 1.0.10) and I want to use Bristuff-0.3 now for the new PBX I am going to set up. With Bristuff-0.2.0-RC8q the ISDN lines are working fine, but the new version of Asterisk add some nice features. All these PBX are in France with France Telecom lines. When I use the new version after about an hour with

so here it is, the problem that's been nagging me for the past 2 days: connected a box to my telco's NTBA <-> zap/asterisk. which works: box:/etc/asterisk# cat /proc/zaptel/1 Span 1: ZTHFC1 "HFC-S PCI A ISDN card 0 [TE] layer 1 ACTIVATED (F7)" HDB3/CCS 1 ZTHFC1/0/1 Clear (In use) 2 ZTHFC1/0/2 Clear (In use) 3 ZTHFC1/0/3 HDLCFCS (In

Hello everybody, I'm having little trouble (well, pretty big trouble) with HFC-S card and Asterisk. My idea is to do VoIP/IAX link between two HW PBXen using two Asterisk PC boxen with ISDN cards in them. AFAIK HFC-S cards must be in NT mode for this installation, they must behave like state line for those HW PBXen. (if wrong, please correct me). Diagram follows:

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 hi, i'm new to * I've installed an hfc-s card (DIGI Micro V) with bristuff 0.0.2; when i try to call outside i get: -- Accepting AUTHENTICATED call from 192.168.1.110, requested format = 1024, actual format = 1024 -- Executing Dial("IAX2[pippo@pippo]/2", "Zap/g1/0123456") in new stack Jul 13 13:42:49

Hello all Asterisk 1.2.10 BRIstuff PRE-1s Debian sarge I have an issue with my ISDN-BRI line. Asterisk tells me my D-Channel is down, no matter is I have an actual line plugged in or not. == Primary D-Channel on span 1 down I somehow got it to work once! The config tools do not indicate any errors whatsoever. Here is a rundown of various listings I can think about. (some things may show

Mine is very similar: i don't have echocancelwhenbridged=yes because it seems work only on TDM, is it ? And in Italy, I often have set pridialplan = unknown About echo I have some problems, but only at the beginning of the call. After 3-4 seconds the echo became almost null, specially with snom 190; with pa168s and ywh10 I have again some problem, the echo come up also after 1 minute of

Hi, i've downloaded/compiled/installed the bristuffed asterisk Asterisk 1.0.7-BRIstuffed-0.2.0-RC8a and i'm using it with an hfc card. It runs on a debian 3.1 sarge machine with kernel 2.6.11. Asterisk works well if i configure the card using isdn4linux. I'm having problems dialing out (not tried the input yet). This is the output from asterisk: -- Accepting AUTHENTICATED call from

Hi all, In our asterisk box we have a Fritz card and an HFC card. So far I've had the Fritz card working well, but its time to connect the HFC card up to the ISDN line and get it working. I've followed the instructions on voip-info.org here: http://www.voip-info.org/wiki-Asterisk+zaphfc+install and here: http://www.voip-info.org/wiki-Asterisk+zaphfc+install But when it comes to

Hi list! I'm totally fed up with bristuff (or it's instability with a simple HFC-S card), 2 out of 3 times when people try to call they get the information tone that the number is not connected. I would like to try vzaphfc and I am looking for information on it. >From previous posts I found that the only place where the sources seem to be maintained and available is at the debian

I guess it is possible to have an HFC-S card and a Digium TE110P card working at the same time? The TE110P will work in E1 mode. I think the zaptel.conf is probably right but the zapata.conf not (I just tacked on another group at the end but I don't really know what I am doing). Can anyone help? ----------------------------------------- My zaptel.conf looks like this: # hfc-s pci a span

Hi there, I am using bri-stuff.0.1.0-RC2k and it seems that things didn't become better. I have got lots of dropouts on the IAX2 link (no matter if jitter buffers are enabled). Further the MP3Player application does not playback streams like http://somestreamserver/somestream. It stops saying: -- Executing MP3Player("SIP/27870-ba4f",

Hi, I'm trying to set up an Asterisk pbx based on a Fedora Core 1 Linux box (customized kernel version 2.4.24). I want calls from my SIP soft-phones to simply be dumped onto the PSTN line via a BRI (EuroISDN). I have a cheap HFC-S based PCI ISDN card connected to the NT1+ interface, so I need zaphfc. I've read everything I've found at www.voip-info.org, then I've downloaded the