similar to: Building and running mISDN for B410P on Ubuntu 7.04

Hi, Until now I've been using my Digium B410P cards with misdn 1.0.x. I would like to upgrade my systems and am now wondering which is the "best" route to take: - use the latest release of misdn v1 - upgrade to the latest "stable" kernel and use the built-in misdn v2 - use misdn v2 as a seperate package (disable misdn in the kernel) - use dahdi's support for misdn

Hi. Using Asterisk 1.4.13 running on Ubuntu 7.04 with Intel CPU: 1) Is it possible/supported to install two or more B410P Digium cards in one computer (single Asterisk installation)? 2) Do they need to be hard-wired together with a PCM cable like I've seen explained in some beronet manuals (although that was specifically geared towards their cards, I must say)? Thank you for your time and

Hi, I'd like to know what's the most "popular" method for automatic fax/voice detection for incoming calls on mISDN cards such as the B410P (hfcmulti). I'm running: kernel 2.6.17 misdn 1.1.3 asterisk 1.4.21.2 B410P card I'm using iaxmodem and hylafax with asterisk (the setup works for zap channels). I've used the following options in /etc/asterisk/misdn.conf:

Hi. I have installed B410P in Europe and the cards works more or less ok. My question is what color should the LED's on the back of the card be when connected to the PSTN NT box? Is there anywhere some information on the expected LED color in any given state (idle, call active, cord unplugged etc.)? On my card the lights are shining Red(orange-ish) but flashing to green every now and

Hello, I'm evaluating to possibility to use chan_misdn as a short term workaround, in case latest Dahdi is not stable enough for what we are planning to do (we wish to use Junghanns and Digium BRI hardware with Asterisk 1.6) . I've read www.mISDN.org but still have a couple of questions : 1. Is correct that in a 2.6.27 (and up) enabled kernel, the "embedded" mISDN version is

The DAHDI docs actually include the 'steps' that used to be in Zaptel's 'make b410p'. These steps involve downloading and compiling mISDN. Why re-invent the wheel? Just a thought :-). As for the 100ohm termination bit - it's simply changing a couple of dip switches on the b410p card (as described in the manual). Andy -----Original Message----- From:

Hi, I'm installing Asterisk on Ubuntu 6.10 When I first compiled the zaptel package I used: make clean make make install So far so good, but the following command failed: make b410p I did some digging on google and found a guide on how to install it manually, but the result was the same. I got these files ftp.digium.com/pub/telephony/zaptel/b410p/misdn-b410p.tar.gz

Hi. When I call my RNIS numbers (with a mobile phone for example), I can see 2 incoming calls on the IPBX, which should not happend. I'm not sure if it's a problem with the telco France Telecom and their ISDN setup, or if it's a problem with the MISDN driver on the IPBX itself. I'm stuck ... Any advices for troubleshooting that? Someone provide working configuration files

Hi all! Sorry for my poor english, i'm italian. I installed Digium B410P on my asterisk server. I followed the official installation instructions found on digium site. These instruction, in my opinion, are not clear, so i tried with other ways (found on the trixbox site). I found this: http://www.trixbox.org/forums/trixbox-forums/trunks/howto-install-script-digium-b410p Now i can receive

Hi list, Is Digium Wildcard B410P compatible with Asterisk 1.2 / 1.4 (zaptel of course) directly out of the box, or do I need things like bristuff? http://www.digium.com/en/products/hardware/b410p.php Best regards, Henrik Woffinden

Hi, I've been able to make make install the Zaptel drivers (1.2). I'm using a b410p so I executed the following command make b410p. I tried this on multiple machines, but it always failes: root@asterisk:/usr/src/zaptel-1.2.11# make b410p [ -f misdn-b410p.tar.bz ] || wget ftp://ftp.digium.com/pub/zaptel/b410p/misdn-b410p.tar.gz --23:59:54--

Hello all, I'm trying to conect two asterisk servers using two B410p Digium cards. One card on each server. I just setting up the first BRI port on server A as nt_ptp and the first BRI port on server B as te_ptp. I use an ethernet wire to connect the first port of server A (nt_ptp) with the first port on server B (te_ptp) but the port light cotinues blinking on red on both sides once the

Hi all, I am having trouble setting the signalling method for the B410P using DAHDI. Asterisk complains that it has never heard of 'bri_cpe' or 'bri_net' - but it doesn't mind having 'pri_cpe' etc. ERROR[4294]: chan_dahdi.c:11327 process_dahdi: Unknown signalling method 'bri_net' Dahdi - dahdi-linux-complete-2.1.0.4+2.1.0.2 Asterisk - 1.4.23.1 Libpri - 1.4.9

Hi list, we have a dual Xeon server with 2GB RAM running Debian Etch 2.6.18.4-686 kernel. The server has 2 B410P cards plugged in. No other card. We installed Asterisk 1.4 trunk with zaptel trunk, ran make b410p, the install mISDN1.1.0 (for bug 9064) configure and compile Asterisk with chan_misdn, all is fine. In misdn-init.conf we have added option=1,master_clock. Asterisk is up and

Hello, Junghanns and BeroNet offer 8 BRI ports cards. Do you know if Digium's B410P has an inner TDM bus so that an 8 BRI ports subsystem (2 PCI slots used, but 1 one set of interrupts) could be made out of 2 B410P ? I know you could (theorically) do this with Junghanns and BeroNet cards. Cheers -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi. I have two B410P ISDN BRI cards in one machine running Asterisk on Ubuntu 7.04. One card connects to the PSTN network and is therefore in TE mode on all four ports and the other card is in NT mode and connects to a PBX. The Asterisk is used to remap features, callerid's and more from the PSTN to the PBX. 1) Is there any special care I need to take regarding the configuration for

Hi list, I installed a fresh Debian/Etch with Asterisk 1.4 and Zaptel 1.4 from SVN for 2 Digium B410P card. I ran configure in Asterisk dir, went in zaptel dir and: make, make install, make b410p. Everything is ok. Now I want to compile Asterisk but can't activate the chan_misdn channel which depends on -from menuselect- isdnnet(E), misdn(E), suppserv(E) When I made the make b410p, all

Apart from you were dialling out on your inbound context and vice-versa. The best advice I can give now is to change to mISDN - as this is proven to work with v1.4 and v1.6. Actually - have you tried putting the 100ohm termination on for your NT port? I need to do that with mISDN as it only allows ptmp for ISDN extensions. Cheers Andy -------------- next part

Hello, I have some problems with mISDN. I can't send or receive call from the Billion ISDN card Mi configuration files are thoose: extensions.conf: [general] static=yes writeprotect=yes [SOME] exten => 101,1,Dial(SIP/101,30,Ttm) exten => 101,2,Hangup exten => 102,1,Dial(SIP/102,30,Ttm) exten => 102,2,Hangup include => outgoing [outgoing] exten

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all, We have a BRI installation who is experiencing constant echo with the Digium b410p and mISDN. I have adjusted gains, and originally thought that the desktop phones were at fault, although we experience the same problem when a call is bridged out to an external number. I've tried it with 128 taps (the default and I believe the supported