similar to: WARNING: chan_zap.c process_zap: Ignoring signalling

Hi Guys I'm configuring a TE212P card and have the following two entries in my /etc/asterisk/zapata.conf switchtype=dms100 signalling=pri_cpe When I reload asterisk I get the following messages: > -- Reloading module 'chan_zap.so' (Zapata Telephony) > == Parsing '/etc/asterisk/zapata.conf': Found > [Mar 30 17:48:42] WARNING[2985]: chan_zap.c:11072

install asterisk with x100p clone; the problem is that call me and hangup but the interface zap not detect the hangup and the line open. the error is : The 'reload' command is deprecated and will be removed in a future release. Please use 'module reload' instead. -- Reloading module 'chan_zap.so' (Zapata Telephony) == Parsing '/etc/asterisk/zapata.conf':

Dear All I have a problem with a TDM400 card with 4 x FXS modules. The card carries extensions only and there are no incoming lines. I can make a call to the extension on this card with no problems. However, when I try and call out I just get a busy signal. I also get an error message (as shown at the bottom). Is this a problem? Configs below: [root at asterisk etc]# more zaptel.conf

I am having trouble with chan_zap.so not loading. When I load it from modules.conf, Asterisk bails out without any error message. When I load it from the console, it just says "Unable to load module chan_zap.so" no matter what verbose level I am using. dmesg says: Zaptel Version: 1.4.4 Zaptel Echo Canceller: MG2 Freshmaker version: 73 Freshmaker passed register test Module 0:

Hi, am building the latest version of Asterisk (1.4.13) on a self-build Linux host (based on LFS-6.3). Version 1.4.12 built installed and worked fine. Last night I upgraded the kernel to 2.6.23 and rebuilt the zaptel driver package 1.4.5.1 against it. That seemed to build and install O.K. too. I dl'd the 1.4.13 source tarball and tried to build that: ./configure ran O.k. 'make

Hi all. chan_zap not compiling, yes yes I know this sounds trivial but here me out... This morning I decided to upgrade to Asterisk 1.4.2 and Zaptel 1.4.1. I successfully installed zaptel 1.4.1 and the card is picked up and correctly configured. ztcfg shows the following: [root@zion root]# ztcfg -vv Zaptel Version: 1.4.1 Echo Canceller: MG2 Configuration ====================== Channel

I have been trying for some time now to make the hook flash work on the FXS port. I am using Asterisk 1.4.10.1 with zaptel 1.4.4. When I "manually" flash the hook I can manage to find the duration to put a call on hold. However when pushing the flash button it never works. The phone's flashtime seems to be too short. I tried to set a shorter flashtime in the zapata.conf file, but it

I encountered this strange problem which is I can call into Asterisk box but I cannot call out. I was successful before using exactly the same euroISDN line but with TE110 and different versions of Asterisk. This time, I am using: . TE410 . Asterisk 1.4.13 . Zaptel 1.4.6 . Libpri 1.4.2 1) I put the following into extensions.conf to get to the outside line exten => 0,1,Dial(Zap/1) 2)

Hello, After installing on Ubuntu 10.04 using the tutorial on http://hmontoliu.blogspot.com/2010/03/installing-asterisk-and-freepbx-on.html I have a running instance of Asterisk. PROBLEM: result of dahdi_cfg: DAHDI Tools Version - 2.2.1 DAHDI Version: 2.2.1 Echo Canceller(s): MG2 Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Echo Canceler: mg2)

I am getting quite frustrated today, so please bear with me. I just installed Fedora Core 4 (was running RedHat 9 with a working Asterisk) now my Fedora does not appear to be recognizing my X100P (clone) at all. Hardware browser just shows them as unknown device. driver: hisax So, of course, my zaptel drivers do not work and therefore my asterisk does not work. any help would be greatly

I have seen this in the archives any number of times -- but I have yet to find a solution that works for me. Any suggestions you can offer would be most appreciated. Here are the answers to the questions I have seen asked in earlier posts. The log contains: Mar 10 12:26:29 WARNING[3015] chan_zap.c: Unable to specify channel 4: No such device Mar 10 12:26:29 ERROR[3015] chan_zap.c: Unable

Hello everyone! I installed Asterisk following the instructions of the book "Asterisk: The Future of Telephony". (very nice book) However, I failed. I installed zaptel, libpri and asterisk (in this order). The Installation of Zaptel is successful and my TDM400P is correctly detected: # zttool Alarms Span OK Wildcard S400P

Hi, I' ve just connected a carte X100M to my asterisk server running zaptel-1.2.5, libpri-1.2.2 and asterisk-1.2.6 on SUSE 10.0. When I make modprobe wcfxo and modprobe zaptel I haven't any error, I have also chan_zap.so module existing in /usr/lib/asterisk/modules. But, when i run ztcfg, it shows me this: Zaptel Configuration ====================== Channel map: 0 channels configured.

Hi all, i've installed AMP and Asterisk following the INSTALL file and i have a problem with the TDM04B with 4 FXO: [root@srvoip ~]# ztcfg -vv Zaptel Configuration ====================== Channel map: Channel 01: FXO Kewlstart (Default) (Slaves: 01) Channel 02: FXO Kewlstart (Default) (Slaves: 02) Channel 03: FXO Kewlstart (Default) (Slaves: 03) Channel 04: FXO Kewlstart (Default)

Hi, I have a TrixBox install with a Sangoma A200 and 4 FXO ports, there are 3 BT lines connected directly to these ports. One of the lines has BT FeatureLine Compact and this is the line I am having problems with, the other 2 lines are working perfectly, detecting CID, answering incoming calls and placing external calls via SIP devices. I am receiving a error log entry: chan_zap.c:

Newbie question for sure... I'm unsure of how to tell if chan_zap.so is loaded. Also, does autoload in modules.conf take care of it or is it done explicitly? output of lsmod | grep zap: zaptel 208388 16 wcusb,wctdm,wcfxo,wctdm24xxp,wcte11xp,wct1xxp,w ct4xxp,tor2 crc_ccitt 6465 1 zaptel

I get the following errors when starting Asterisk. == Parsing '/etc/asterisk/zapata.conf': Found Feb 19 21:14:35 WARNING[10440]: chan_zap.c:920 zt_open: Unable to specify channel 1: No such device Feb 19 21:14:35 ERROR[10440]: chan_zap.c:6860 mkintf: Unable to open channel 1: No such device here = 0, tmp->channel = 1, channel = 1 Feb 19 21:14:35

Any ideas? 51] logger.c: [chan_zap.so] => (Zapata Telephony) Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing '/etc/asterisk/zapata.conf': Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing '/etc/asterisk/zapata.conf': Found Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing '/etc/asterisk/zapata-auto.conf': Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing

I installed Trixbox and a TDM400P with 2 FXO and 2 FXS ports and am having an annoying issue with the FXO ports. As soon as I plug either one into the phone line it's as though the line is disconnected i.e. get disconnected tone when trying to dial out, line is busy when dialling in. The CLI shows the following: trixbox1*CLI> zap show channel 4 Channel: 4 File Descriptor: 18 Span: 11*

Hi- I'm totally stumped configuring my TDM400P with one FXS and one FXO module. Before I got the FXO module, I used to have an X101P, and everything was working very well. Now * doesn't seem to recognize the FXO channel. I've searched the wiki and the list archives. Stock Debian 3.0 stable installation. Any advice? Thanks. -- David Here's my configuration: modprobe zaptel