similar to: Secondary Dialtone and selecting a specific line from Zap/g

Dear List; Thanks alot for the help. But how can I let the second dial tone (after pressing the extension to select that FXO port) to be difference than normal dial tone? Regards Bilal Ghayad -------------------------- Correction, on FXO port not FXS, second, read his email first: "Also, how it will be possible to assign an dedicated line (connected to FXO) to an button on the Polycom IP

extensions.conf has ignorepat => 9 exten => _9X.,1,Dial(Zap/G2/${EXTEN:1}) The first user to try it asked if instead of keeping the same dialtone after pressing 9, if I could play a different dialtone. Can this be done? I'm running asterisk 1.0.0 in case that matters.

Hi List; Asterisk does not have any kind of cards that can work with it to be used with Digital Phones (digital phones differ than analoge phone and differ than IP Phones). Anyone can advise about this as I did not find this on Diguim Regards Bilal Ghayad __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around

Hi, I have two asterisks connected via IAX2 trunk. The first * use dial prefix 2XX, the second one 3XX. Calls routing works OK. But I don't know how to get dialtone of remote asterisk pbx. I'd like to get dialtone of asterisk #2 after dialing 3 and dialtone of asterisk #1 after dialing 2. I know something about DISA but I'm not sure if it is a right way. Can you give me advice?

Hello, Sorry, I know I read this somewhere but now I can't find it when I need it. I'd like to force a call to go out one line if we dial '9' first and then the number. Same for '8' only I will force it out a different line. There is a parameter or a method to allow the dialtone to come back after pressing the first 9... but I can't remember how to do it. Anyone know?

Guys.. Im new to asterisk but is it possible to simulate a dialtone for example, in other PBX when you pick up the phone you can hear a certain dialup, which is the PBX dialtone, and when you hit 9, you can hear the PSTN dialtone, is this possible? __________________________________________________________________ Anton Krall

Hi everyone! I'd like to create the following: a user picks up the phone (gets a dial tone), dials '0' for an 'outside' line, gets a second (different?) dialtone, and is able to enter an external phone number. How do I implement this in extensions.conf...? Regards, Evert

Hi All; I got to know (reading on the wiki) that fxotune was have a bug, and it has been fixed. But I do not know if my current asterisk version contain the fixed one or not? How can I know? My current asterisk version is 1.4.22 Any advise? Regards Bilal

Dear List; How can I place a call via Zap/g1 (group) but need to determine the line (FXO port) that will go via it? Also, how it will be possible to assign an dedicated line (connected to FXO) to an button on the Polycom IP Phone or Broadtel IP Phone, so if user select that button then he will be sure that his outside call will be via that specific line. Regards Bilal

Hi I have the following configuration at home one ZAPTEL interface connecting to an FXO card and two SIP UAs connecting to asterisk locally. I have configured extensions.conf such that dialing 9 on the SIP phones allows me to dial an outbound number via the FXO interface . Works fine. What's not working is that pressing 9 should causes either GS BT-100 phone to reacquire a dialtone

Hi All; Can anyone advise if using Cisco IP Phones in skinny protocol is fine or not? Or it is better to use it in SIP protocol? Regards Bilal

I have 2 problems with openswitch12: 1) I can not make work "ignorepat => 9" i do not get dialtone after the number is dialed, the system ignore the number and i can go on dialing the rest of the number.... but when i want to take the line teh dialtone do not stay. 2) when i tray to leave a message on the voicemail of an user i get the following error Sep 3 17:04:55

Hi List; What configuration needed to let my FXS send and receive FAX? Regards Bilal

Hi List; I need to configure a softphone to be client and use it with Asterisk, which is the recommended one? Is it iax2? Regards Bilal ____________________________________________________________________________________ Boardwalk for $500? In 2007? Ha! Play Monopoly Here and Now (it's updated for today's economy) at Yahoo! Games.

Hi All; I do not know if anyone faced such case in dealing with open vpn (as we need it for fring to be used from the mobile: Which mobile can be used to install the open vpn client on it, so we can use it to do a vpn channel with the server that has open vpn server? Regards Bilal

Hi Danny; Really I did not understand how I can determine if the IO will be DB or conf files? Is it from the Asterisk manager? Regards Bilal ------------------------- It depends on how you are configured. The gui interfaces using Asterisk Manager, so you get the Same IO from the gui that you would get from a native manager session. -----Original Message----- From: asterisk-users-bounces at

Hi all, this is a rather "newbie-oriented" question, so please bear with me... The system running Asterisk has been provided with an AVM FRITZ!Card PnP. SuSE Linux 9.0 recognizes it right after booting the system and it seems to be configured (MSN) correctly... The hwinfo looks like this: --- pbx:/etc/asterisk # hwinfo --isapnp 11: ISA(PnP) 01.0: 10300 ISDN Adapter [Created at

I tried putting this as the ata's dailplan: *St4-|#St4-|9|^9t4>$.- this is sip.conf [ata2001] type=friend username=ata2001 secret=SoMeSeCrEt host=dynamic context=fromata canreinvite=no and this in extensions.conf [fromata] ignorepat => 9 exten => _91700NXXXXXX,1,Dial(IAX2/${IAXINFO}@iaxtel.com/${EXTEN:1}@iaxtel) exten =>

Hi All; Anyone knows if there is an Asterisk version that setup can be stored in Database instead of the configuration files (.conf)? Any advise? Regards Bilal

Hi List; How can one Asterisk Box A to send a SIP call for another Asterisk Box B, and that call to be authorized based on the username and password, and not on the IP (as the IP address of the source is not known because it keep changing)? I think the trick in the Dial command, how to write it properly in a way that other Asterisk Box can recognize the sip username and password which are existed