Displaying 20 results from an estimated 10000 matches similar to: "TE207P Question"
2007 Feb 13
4
Nortel 81C MSDL Trunking to Asterisk TE110P, Nortel Resetting PRI Channels
We are currently working to trunk from a Nortel 81C to an Asterisk
Server 1.4 running on Red Hat Linux. We have two PRI trunks which work
with the exception of the clock slips, which is causing the Nortel to
reset the PRIs once a hour. Thanks for any suggestions.
81C MSDL Asterisk Digium
TE110P
REQ prt
TYPE adan dch 10
2005 Oct 04
2
Quad PRI Problems
I have been getting quite a bit of PRI Resets using my Quad PRI Digium
card.
Prior to the resets I am getting similar notices to the following
chan_zap.c:7482 pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary
D-channel of span 3
Telco claims the PRI's are fine on their end and that it is my unit.
Is this timing? (google somewhat leads to this) I am running 1.08
asterisk zaptel
2005 Sep 28
2
Sep 28 00:42:35 ERROR[5151] chan_zap.c: Unkn own signalling method 'pri_net'
Did you compile and install libpri *before* Asterisk? I had same problem
(among others) b/c I didn't install in the correct order. Try the awesome
asterisk_update.sh shell script.
Are you trying to emulate CPE or NET? Try signalling=pri_cpe
Check for whitespace behind the statement, zapata.conf seems bitchy about
whitespace.
hth
-----Original Message-----
From: Steve Totaro
2005 Sep 28
1
Sep 28 00:42:35 ERROR[5151] chan_zap.c: Unknown signalling method 'pri_net'
Any ideas?
51] logger.c: [chan_zap.so] => (Zapata Telephony)
Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing '/etc/asterisk/zapata.conf': Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing '/etc/asterisk/zapata.conf': Found
Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing '/etc/asterisk/zapata-auto.conf': Sep 28 00:42:35 VERBOSE[5151] logger.c: == Parsing
2005 May 16
1
2 servers via PRI
Good day all
How do i set a connection between 2 asterisk servers via PRI
In Bri I would set one to NT and TE
How shoud the zapata.conf and zaptel.conf look
And how should the cable be?
All I got on the web was to set one to "pri_net"...this cant be all?
And the cable
> pin1 <--> pin4> pin2 <--> pin5> pin3 <--> pin6> pin4 <--> pin1> pin5
<-->
2004 Dec 03
3
Two zaptel T1 cards: no clock from one
List,
I have a TE410P (T1 mode, all PRI) and a T100P (fxoks, for fxs channel
bank). I cannot seem to get the T100P to send any clock to the
channel bank. I prefer that it use the same clock source as the
TE410P, but it doesn't matter if it's not in sync just as long as it's
there.
The TE410P is configured 3x pri_cpe, 1x pri_net. The three cpe go to
XO Sonus switch, the net to
2008 Mar 03
2
T1, Rhino, & Nortel
Hi all,
I'm trying to insert a Rhino Ceros box equipped with a Rhino R2T1
dual-T1 card and running the latest version of Trixbox (2.4.2) between
the central office and a Nortel Option 11. The switch at the CO is a
DMS100. Basically, I'm taking the T1, connecting it to port 0 on the
R2T1 card, and then connecting port 1 to the Nortel. (Actually a CSU and
then the Nortel) We're running
2012 Sep 26
1
Asterisk 1.8.15.0, Requested transfer capability: 0x00 - SPEECH
Hello,
I'm having issues connecting throu PRI with the following error "Requested
transfer capability: 0x00 - SPEECH"
Below are the logs:
== Using SIP RTP CoS mark 5
-- Executing [97052660 at voipphones:1] Set("SIP/4856-00000003",
"CALLERID(num)=xxxxxxxxx") in new stack
-- Executing [97052660 at voipphones:2] Dial("SIP/4856-00000003",
2006 Mar 22
3
PRI DMS100 -> Nortel Meridian Option 81
Hello all,
I have Asterisk 1.2.1 and a TE110P connected to a Nortel Meridian Option
81C system. The PRI line is currently setup as DMS100. Here are the
relevant lines from zaptel.conf and zapata.conf:
zaptel.conf:
span=1,1,0,esf,b8zs
bchan=1-23
dchan=24
loadzone = us
defaultzone = us
zapata.conf:
[channels]
language=en
context=from-internal
musiconhold=default
switchtype=dms100
2007 Aug 01
3
TE120P in Canada
Hi All,
I'm having problems trying to get a TE120P operational in Canada.
I keep getting a congestion error when I try to make a call. I'm not
sure if my switching, parity, etc is correct. I'm hoping that someone
will be able to verify my config.
The Telco is SaskTel, with a 10 channel 50 DDI service.
Zap show channels show and ztcfg -vv looks ok and the zttool show
2005 Feb 11
2
Question about DID
Hello Group
I have a Asterisk server running with 2 Digium T1 cards installed. 1
card connects to Telco via a PRI. The 2nd card is connected to a fax
server via Digi DataFire RAS 24 PT1 Adapter (Digi0001). The idea is to
have Asterisk route the calls based on DID or FAX tones. Everything is
working great so far. The only problem is the Fax server does not see
the DID. How can I tell if Asterisk
2004 Mar 16
7
PRI Errors
I just had the same exact problem this morning. The only thing I've done in the last couple of days is update update zaptel. I rolled back my zaptel to 2/11/04 from 3/8/04. And kept my libpri from 3/8/04. I never had this error before updated. I had other issues, but not this one.
-sb
-----Original Message-----
From: asterisk-users-admin@lists.digium.com
2003 Nov 21
1
Echo Cancellation, TDMoE fails, X100P works
We have been pretty much able to solve our echo problems, except for
the primary mode in which we desire to operate our system.
See system diagram at bottom.
Prior to making adjustments to cancel echos (all echocancel=no):
Call Type Result (Before)
--------- ---------------
CP <- LEC PRI * TDMoE * FXO -> AP
2006 Jan 25
20
* point to point t1 solution?
Can anyone point me to a reference or sample config for bypassing a
nailed up (point to point) t1 between two PBXs with asterisk and a pair
of t1 cards?
Right now I have 2 Nortel norstars connected to each other via a leased
line t1. I also have a solid 10mbps low latency microwave link between
the 2 sites.
My goal is to run an asterisk box at each end with a t1 card and
Ethernet card to
2009 Sep 18
1
No more room in scheduler
Hi,
I running into the following problem on my Asterisk setup:
--snip--
[Sep 3 01:40:59] NOTICE[9170] chan_dahdi.c: PRI got event: HDLC Abort
(6) on Primary D-channel of span 3
[Sep 3 01:47:07] ERROR[9170] chan_dahdi.c: No more room in scheduler
[Sep 3 01:47:07] ERROR[9170] chan_dahdi.c: Asked to delete sched id -1???
[Sep 3 01:47:07] ERROR[9170] chan_dahdi.c: No more room in scheduler
[Sep
2008 Nov 15
1
PBX -> PRI -> * -> Telco not working
Hello all.
I have an NEC PBX connected via a TE210p E1 line to an asterisk 1.6 box.
NEC -> E1 -> TE210P:1 -> * -> TE210P:2 -> E1 -> Telco
Incomming calls from the telco to the asterisk box to the NEC work fine with
indials and everything. Works sweet.
Outbound from the NEC to the Asterisk box fail. Giving an long dial tone
that then times out.
Ie, pick up NEC handset, dial
2006 Apr 29
2
problame with outbound calls on pri
Hi. recently I have been trying to setup a PRI on asterisk. Inbound
calls are working just fine but I am not able to make outbound
calls. Does anyone know what I need to change to make outbound
calls work? Right now the PRI is instantly hanging up on the outbound calls.
I have included full debug info as well as config files.
/etc/zaptel.conf
span=1,1,1,esf,b8zs
bchan=1-23
dchan=24
2006 Jan 24
13
Nortel Meridian Opt 81C and PRI
We've been trying unsuccessfully to connect our Meridian Option 81C to a
TE110P via PRI. We've followed the directions in
asterisk-meridian-a1.pdf (link on
http://www.voip-info.org/wiki/view/Asterisk+legacy+integration), but it
doesn't seem to work on our 81C (even though many, many users report it
works very well on Option 11's).
Has anyone had any success in getting the above
2006 Apr 30
2
PRI Issue: D-Channel woes
Hi,
I am about to pull my hair out after trying to get our PRI up and working.
We are switching from a Cisco gateway to an Asterisk box which provides
the 23 phone lines for our office. So, because the Cisco gateway is
working I can assume I have all the settings right (b8zs, esf, dms100,
etc) and the PRI is live (because we are switching over). When dialing
from PSTN, I get busy signal. When
2005 Apr 22
4
TE11OP -> Mitel 200Sx??
Hello all. I just received a TE110P and am trying to hook it to my Mitel 200SX has anyone successfully done this? My configuration is as follows.
Asterisk -> TE110P ->Kentrox (csu/dsu) -> Mitel T1 Card.
All I get is a blinking yellow on my TE110P card and an alarm on my Mitel. T1 card.
Any advice would be great.
Zaptel.conf
span=1,0,1,d4,ami
e&m=1-23
dchan=24