similar to: Avaya SIP phones (4610SW) and MWI

I just registered an Avaya 9620 set to my Astlinux system (0.47 - Asterisk 1.2.22), using Avaya SIP Firmware version 2.0.1.34. Set mailbox=ext at default in the sip.conf Found MWI worked immediately. Turned off as expected. Have Fun! Tom -------------- next part -------------- An HTML attachment was scrubbed... URL:

I have an Avaya 4610SW IP phone which I have upgraded to SIP firmware. I have successfully registered this phone to Asterisk BE as well as Asterisk 1.4.18 Almost everything is working well. Except for two issues. One of the problems is that the phone looses registration every now and then ad I have to re register. I have found a tip for this which I am testing if it will work, which

Hi ! I want to install a Telephone IP Avaya 4610SW in my Asterisk 11, but I cant install. It asks a TFTP/HTTP Server, but is necessary I install it in mu Asterisk Server for works my Telephone? The manual is here https://downloads.avaya.com/css/P8/documents/003880182 Thanks in advanced.

Hi all, I've been pulling my hair out for two days over this problem... I did *a lot* of Googling around, I searched the list archives to no avail - no one has the same problem! I have two Avaya 4610sw phones. I installed the latest SIP firmware using the TFTP server. So far everything looks good. Each time the phone boots, it retrieves the 46xxsettings.txt from the TFTP server. My problem

I have an Avaya 4602 IP phone that was previously working with Asterisk. It was being used elsewhere for several months, and I recently set it up again to work with Asterisk. Everything works fine for several minutes -- I am able to receive and make calls as expected. However, after a few minutes, and every few minutes thereafter, I get the following message on the console: -- Got SIP

I have a situation that I need help with. I have 2 phone systems, 1 Asterisk and 1 Avaya. All voicemail is kept on the Avaya system. Whenever a call comes into an extension that the Asterisk server owns, I re-direct it to a different number that is owned by the Avaya System. If that Avaya extension does not answer it, I send it to the voicemail on the Avaya Messaging system for the extension that

Hey everybody, I've just spent the last two hours Googling and searching the Wiki. I'm trying to find if there are any listings of codes for the Avaya Definity G3R, to allow for an Asterisk system to turn on/off a phones MWI that is attached to a G3. We are looking to use an Asterisk system as a voice mail server. I'm not having any luck, anybody have such information? Thanks,

i was reading posts on wiki and noticed lots of posts about Avaya 4610 handset having issue with MWI, Anyone has any more updates? Is this still the case? Any good tutorial for configuring these phones and Asterisk? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20080318/3d397ca7/attachment.htm

Has anyone tried to set Message Waiting Indicators up when public network access and voicemail service are managed by an Asterisk server TDM-connected to a legacy PBX serving analog and digital phones ? For instance: Location 1: - 200 users on a legacy PBX - among those users, 50 have access to voicemail service - TDM trunk to Location 2 Location 2: - 100 users on Asterisk - PSTN access - TDM

I have added H.323 support for ASTERISK PBX using the OpenH323 library. I thought that since the Avaya IP phones are H.323 phones I will be able to make them register to Asterisk server. Does anyone know if this is possible ? Katerina

I remember someone posting here some time ago about commercial offerings for taking channel banks of Avaya partner phones and turning them into asterisk compatible (SIP?) devices, but I can't seem to find a reference to the hardware manufacturer or specific experiences. Would anyone care to enlighten me? Off list is fine if this is a repeat, thanks very much. Matt -------------- next part

Hi All; In cisco IP Phone, I can assign for a features for the buttons at the Phone (one button to be for call pickup and one button to be for call forward and button to be for bridge and one button to be for another extension). How can I do the same thin in the Cisco IP Phones (or other IP Phones) while they are registering in Asterisk? Regards Bilal

Hi All; How to configure the buttons in the Cisco IP Phones to be used for different functionalities like "Call Forward, Call Pickup, ... etc"? For example, if I need to assign one of the buttons existed at Cisco IP Phone to be used for CallFrw, how to do this in Asterisk? Regards Bilal

The company I work for has deployed an Avaya IP phone system. They have deployed the Avaya 4602 and 4620 IP telephones. They might be sending me one of these phones for use in my home office. Question: Can I make this IP telephone register and work with my Asterisk server? I don't know if it is a SIP phone? I searched thru the Avaya site, but can't find whether it's a SIP phone or

Hi, Is anyone using Avaya's 4624 phones with Asterisk? If you are, was there any special trick to get them to register with the openh323 gatekeeper? TIA, Trevor

Hi All, I'm looking for a good voip hardphone that has a decent set of the "regular" features (conference, 2 lines, etc) thats reliable, has decent quality, and isn't too pricey. Does anyone have any suggestions? Thanks in advance. Derek -- Derek Fedel

Hi All - I'm running version SIP version 1.3.4 on various IP300, IP500, and IP600 Polycom phones. I'm having a tough time with MWI. I thought I remembered somebody on the list saying that they had it working, but I can't find it in the archives now. I have all the phones configured for MWI as specified in the WIKI: ipdmid.cfg: up.oneTouchVoiceMail="1"

Hi all, When moving from a self compiled Asterisk 13.23.1 to Asterisk 13.24.0, has resulted in a MWI clearing delay of around 5 minutes. After listening to a voicemail and deleting it, the Polycom VVX 601's MWI light is left on for around five minutes, before clearing. Installing Asterisk 13.24.1 did not fix this. Moving back to 13.23.1 allows the MWI to clear immediately. I see a note in

Hi all, I'm having sudden MWI problems. Everything else on the phone works fine though. I have three Cisco 7940s. Asterisk server is behind a firewall running NAT. (192.168.1.202/24) Phone #1 - On the same subnet 192.168.1.250. Everything works great. Phone #2 - On a different subnet, 192.168.2.0/24. Everything works fine except the MWI. It never comes on. This is over an IPSEC VPN, but

Hi Guys, Running Asterisk v1.4.26 (Elastix flavour) and have Aastra 9480i, 6757i, and 6730i, but none of them indicate the voic-email. Where should I look for trouble to find the root issue for MWI? Thanks, -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20100714/d268d1f8/attachment.htm