Displaying 20 results from an estimated 10000 matches similar to: "problems with dtmf using asterisk-1.4 rev r 6745"
2009 Dec 13
1
Random DTMF tones generated from speech
Thank you, very interesting!
As I understand the Digium card is used as a interrupt source for Asterisk?
Is there a diagnostic tool available ?
Anybody else experienced a simmialr problem?
Thank you!
HB
> From:
> covici at ccs.covici.com
> Date:
> Sat, 12 Dec 2009 19:04:23 -0500
> To:
> Asterisk Users Mailing List - Non-Commercial Discussion
<asterisk-users at
2007 Oct 24
1
Unusual DTMF behavior
We are having an issue where DTMF is not being sent out right away and the
tone duration is inconsistent. For a test we send a '5', then a second
later we send a '9', and then five seconds later we send a '5'. If you look
at the logs below you can see the first '5' is played right away, then the
'9' comes in and gets queued, but it doesn't start
2008 Feb 25
2
cannot dial out with latest zaptel and kernel 2.6.24
Hi. I am using asterisk 1.4 (latest as of today) and zaptel 1.4
(latest as of today) and I cannot dial out using my 400P card with one
fxs module and one fxo module. I am using kernel 2.6.24 and get the
following log entries:
[Feb 25 17:28:13] VERBOSE[25071] logger.c: -- Executing [s at macro-dialout-trunk:23] Dial("Zap/1-1", "ZAP/4/www411|300|wW") in new stack
[Feb 25
2010 Jun 03
1
11.6.2 segfaults after dtmf on dahdi channel
Hi. I have been using asterisk-1.6.2 and if I update the version --
using svn -- to around May 19 or after, when I dial a digit on my fxs
port which is on an X400p card, asterisk seg faults. If I go back
before about this date, this problem does not occur. The dahdi version
is svn 7445.
Any ideas would be appreciated.
--
Your life is like a penny. You're going to lose it. The question
2011 Apr 05
2
dahdi and linux-2.6.38
Under linux-2.6.38 I was able to compile and install dahdi, however when
I ran dahdi_cfg -vv, I got an invalid argument on my fxs port. I have
an old 400P card with one FXS and one FXO module. I have
dahdi-trunk r9868 and dahdi-tools-trunk 8670.
How can I get this to work correctly?
Thanks in advance for any ideas.
--
Your life is like a penny. You're going to lose it. The question
2005 Aug 27
1
dtmf not being detected from viatalk
I am using viatalk as my voip provider and they use dtmf=rfc2833, but
asterisk is not seeing any of the dtmf. I am using CVShead as of
8/26/05. Nothing in the logs indicates a dtmf is being seen. If I
use my pots line it sees it fine.
Any assistance would be appreciated.
--
Your life is like a penny. You're going to lose it. The question is:
How do
you spend it?
John Covici
2009 Apr 13
3
duration of rfc2833 generated dtmf
Hi. I have a SIP provider which wants RFC2833 for the dtmfmode,
however I would like to increase the duration of the tone, its pretty
short and some IVR's are unhappy or don't detect it. I did poke
around, but it looks like when RFC2833 is used, it actually generates
rtp packets of some sort, so I have no idea how to increase that
duration.
Any assistance would be appreciated.
--
Your
2013 Jul 05
1
problem with dtmf detection in asterisk 11
Hi. I am having problems with asterisk detection dtmf properly in
asterisk 11. I am up to rev 390229. Now, when coming in off a did we
have with Velocity, the dids work fine, but from extensions often it
misses digits -- I can type *4 and it will miss the 4. Often, if I type
quite slowly things will work properly. All dtmf modes are set to
rfc2833. Strangely enough, I did not notice this with
2007 Feb 07
0
one touch recording problem in asterisk 1.4
Hi. I was using asterisk 1.2 on a box with sip phones attached and a
long distance T1 line as the phone provider. We did a successful test
of *1 allowing one-touch recording as set in the features.conf.
Because of deadlock issues I decided to try 1.4 (latest svn as of
yesterday) and the deadlock went away, but when we tried to use the *1
it was sent over the bridged channel rather than being
2006 Dec 22
1
problems using the 1.4 version of meetme
Hi. I am having a strange problem when using the 1.4 version of
asterisk and zaptel. If I call from a pstn line into the asterisk box
using a phone number which calls the box via sip, then once I am in
the meetme conference nothing happens when I hit the star key -- I
cannot get the user menu. There is nothing in the logs at all its as
though asterisk never sees the digit at all. Now if I do
2009 Dec 12
3
Random DTMF tones generated from speech in conversations
Hi,
My Asterisk systems runs like a dream with mISDN, SIP and even and old
Digium board. But have almost in every conversation some irritating DTMF
being generated. The seems to be just as often from all trunks but are
worse if noise load speaker in other end.
Any good advices?
Where to look for forgotten DTMF detection settings?
Thank you!
HB
2006 Oct 30
0
Problem with Digium 400P and asterisk 1.4
Hi. Ever since I bought my Digium 400P with 1 FXS and 1FXO module,
once in a while I hear what sounds like a touchtone in my ear on a
phone hooked up to the FXS module. This was not heard by the other
side, and although it was annoying, it was not too much of a problem
till I was using the asterisk 1.4 (rev 46317) and the beta of zaptel
1.4 (rev 1536). Doing this, the toutchtone noises once
2015 Dec 29
1
permission problems trying to access subdirectories of a samba share
Rowland penny <rpenny at samba.org> wrote:
> On 29/12/15 15:44, covici at ccs.covici.com wrote:
> > Rowland penny <rpenny at samba.org> wrote:
> >
> >> On 29/12/15 13:59, covici at ccs.covici.com wrote:
> >>> Hi. I am having problems accessing subdirectories on a samba share. I
> >>> am using windows 10 build 10586 and linux kernel
2006 May 01
0
anyone have solution to dtmf problem in console driver?
Hi. I have become interested in the console driver because it would
be nice to have a nice usb conference phone to use with asterisk -- my
problem is that if you are on a call you can only dial one dtmf digit
at a time -- all the subsequent digits are ignored. Any one have a
solution to this problem?
I am using version 1.2.7.1.
Any assistance would be appreciated.
Thanks.
--
Your life is
2015 Dec 29
2
permission problems trying to access subdirectories of a samba share
Rowland penny <rpenny at samba.org> wrote:
> On 29/12/15 13:59, covici at ccs.covici.com wrote:
> > Hi. I am having problems accessing subdirectories on a samba share. I
> > am using windows 10 build 10586 and linux kernel 4.1.15-gentoo and samba
> > 4.2.7. I have two shares, one called audio and the other called
> > myshare. I cannot access the subdirectories
2019 Oct 07
2
problem with new install with asterisk 15.7.4
Oh, I forgot to mention that Asterisk 15 went End-Of-Life last Thursday.
:) You should use Asterisk 16.
On Mon, Oct 7, 2019 at 5:58 AM George Joseph <gjoseph at digium.com> wrote:
>
>
> On Fri, Oct 4, 2019 at 1:19 PM John Covici <covici at ccs.covici.com> wrote:
>
>> Hi. I am trying to install asterisk 15.7.4 from git onto a Debian 10
>> system and I am
2010 May 23
2
Dahdi problems with kernel 2.6.32
Hi. I am having problems with dahdi using kernel 2.6.32. I am using
2.6.30 kernel and it works fine -- here is the output of dahdi_cfg -vv
++ dahdi_cfg -vv
DAHDI Tools Version - SVN-trunk-r8670
DAHDI Version: SVN-trunk-r7445M
Echo Canceller(s):
Configuration
======================
Channel map:
Channel 01: FXO Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 01)
Channel 04: FXS Kewlstart
2007 Mar 12
1
Problems with Voice conferencing
How did you install these packages -- make sure you do ./configure and
if needed make menuselect in each one of these before the make and
make install. This is the only thing I can think of -- check whether
there are any built-in modules as well.
on Monday 03/12/2007 Asterisk Asterisk(asteriskbunnies@yahoo.com) wrote
> Hey!
>
> Thanks for your interest, i checked the modules and i
2015 Dec 29
2
permission problems trying to access subdirectories of a samba share
Hi. I am having problems accessing subdirectories on a samba share. I
am using windows 10 build 10586 and linux kernel 4.1.15-gentoo and samba
4.2.7. I have two shares, one called audio and the other called
myshare. I cannot access the subdirectories in the myshare share. Here
are the definitions.
[myshare]
comment = root directory
path = /
#fake oplocks = yes
writable = yes
printable =
2009 Nov 01
1
asterisk 1.6.0 seems to have improper dial status when dialing dahdi extension
Hi. When I dial a Dahdi extension using asterisk 1.6.0, and there is no
answer, the extension hangs up, but the dial status is busy instead of
no answer. How do I get this to work -- do I need to update dahdi? The
card is an X400p using its FXS module.
Thanks in advance for any ideas on this.
--
Your life is like a penny. You're going to lose it. The question is:
How do
you spend it?