similar to: TDM400p and te110p configuration.

Dear all. I have what appears to be a configuration error but I cannot for the life of me see what it is. (I am a newbie) I have searched the wikki and google etc but still none the wiser. Any help would be very gratefully received. Problem: Unable to make outgoing calls via E1 euroISDN Digium TE110p card, given congestion signal as per config, unable to open zap channel. All incoming calls work

Hello all. I have here a TE110P (configured as E1) and a TDM400P (with four X100P - FXS). Both boards are recognized by the operating system as showed above: 0000:08:00.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface Subsystem: Unknown device b1d9:0003 Flags: bus master, medium devsel, latency 64, IRQ 169 I/O ports at e800 [size=256]

Dear All The setup is te110p with an 8 channels PRI to make and receive all calls. SIP phones throughout the company. TDM400p with 4 FXS modules to send/receive faxes and make credit card transactions. I have an analogue phone on the tdm400p for testing. I can receive calls to the exten. There is a dialing tone. However, when I try to make a call I get a busy signal. Asterisk stated busy then

Fedora Core 6 regards, Pablo. On Thu, Mar 08, 2007 at 05:01:15PM -0800, Jose Bertuzzi wrote: > Hello Everyone, I checked with zttool that sometimes after the machine boots the order of the boards is changed like this: > ??? Alarms Span ??? OK Digium

Hello Everyone, I checked with zttool that sometimes after the machine boots the order of the boards is changed like this: ??? Alarms Span ??? OK Digium Wildcard TE110P T1/E1 Card 0 ??? OK Digium Wildcard TE110P

Hey there, What recommendations does anybody have as to motherboards known to work well with the Digium TE110P T1 interface cards and the TDM400P analog POTS interface cards? We currently make use of the TE110P for our T1 (esf w/ b8zs - not a PRI) and have experienced many issues caused by our PBX's motherboard. Additionally, we built a server to become our new PBX, but that machine runs

Hi, I wonder if anyone is using Digium's TE110P card on an E1 connection. I have been try to, but so far it wasn't much of a success. It only works more or less in EuroISDN as PRI CPE. And even that config gives me some trouble with channel negotiation. My current config: *zaptel.conf:* span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone=be defaultzone=be *zapata.conf:* [trunkgroups]

Hi All, I have configure my Asterisk as follow (using Asterisk@home): [zaptel.conf] span=1,1,0,ccs,hdb3,yellow bchan=1-15,17-31 dchan=16 loadzone = uk defaultzone=uk [zapata.conf] [channels] switchtype=euroisdn pridialplan=local prilocaldialplan=local internationalprefix=00 nationalprefix=0 usecallingpres=yes busydetect=no ; not need on pri callprogress=no ; was yes but wiki says experimatley

I am running Asterisk 1.0.9 and have been running all my calls through a VSP over a IAX2 trunk however we have recently purchased and connected a TE110p to a PRI ( E1 with 16 voice channels ) through Optus. I can make outgoing calls via it fine, however incoming calls are dropped after a few seconds ( or as soon as a command like Playback, or the call is picked up if forwarded to a SIP

Hello, I'm having problem with a wildcard TE110P. As soon as I load the module (wcte11xp for kernel 2.6.10), it spawns a yellow error with or without an E1 plugged-in. Any one managed to set it up in France? Here are my files: zaptel.conf: span=1,0,0,ccs,hdb3,crc4 bchan=1-15 dchan=16 bchan=17-31 zapata.conf: [channels] language=fr context=default switchtype=euroisdn pridialplan=unknown

Hello I have upgraded our asterisk box from zaptel to dhadi two weeks ago... Since, there has been quite a significant amount of echo when making a call. Only for the local outgoing call, the person on the other side doesn't hear any echo. This is with a TE-110P ISDN PRI card .. I've pretty much took the original zaptel configuration and used it as-is with the dahdi one ; to no

I guess it is possible to have an HFC-S card and a Digium TE110P card working at the same time? The TE110P will work in E1 mode. I think the zaptel.conf is probably right but the zapata.conf not (I just tacked on another group at the end but I don't really know what I am doing). Can anyone help? ----------------------------------------- My zaptel.conf looks like this: # hfc-s pci a span

Hi, I have an asterisk installation with 2 E1 cards Software version is Asterisk 1.2.6 Libpri 1.2.2 Zaptel 1.2.5 I'm having problem with fax transmission, let me explain better my setup: My fist TE110P E1 card is connected to the telco line the second TE110P E1 one to an Nexspan PBX so the server is basically sitting between the line, and the pbx. every call coming from the line is

Hi I'm having difficulties getting up my TE110P (running as a E1) when I connect it to the PRI. If I start the server with a loopback connector everything seems fine and the led is green but when I connect it to the PRI the flashing starts .... I can't seem to find anything in the log that suggests what could be wrong .....Aug 8 11:33:00 DEBUG[1369]: Updated conferencing on 31,

>> So it sounds like it should "just work". I'll let you know in a few >> weeks time :) > TDM400P to E1/T1 card faxing fails by design. The lack of > synchronisation between cards means it can *never* work with any > reliability. The hardware will not permit it. >> >> (And I know I've asked this before, but any recommendations for a >>

Hi, Been asking google and browsing the lists but haven't found any answers for this. I've connected a TE110P E1 using EuroISDN to a PBX (for me at the time unknown model). All is fine _except_ when placing calls to mobile phones (which takes too long, more than 2 seconds it seems) asterisk seem to be impatient giving up saying the curciet beeing busy. So, what I'm looking for, is

Try different entry in this parameter. In Italy mobiles start with 3, while public services with 1 and normal user numbers with 0. Using pridialplan=none, every number different from 0 was resulting in termination code 1, normally used for number never seen on the network. Ciao Mauro

We are in the process of installing a PRI line and we are going to connect it to an Asterisk Box. Verizon called us today to find out some information. I am surprised that they have never heard of Asterisk or Digium. But anyways, they needed some information in order to set up the circuit. Does the TE110P support NI1 or NI2? (I think the answer is both) What is the number of digits

Hi guys, I've been installing and configuring a TE110p card. The compile and install went very well. I'm using this on FC4 and I compile with linux26 as well checked I on the udev configs. zttool and ztcfg both indicate that the card is ready. But when I try to "load chan_zap.so" then I get the following Unable to load module chan_zap.so Jan 5 21:43:33 ERROR[6808]:

please can someone send to me his files like zaptel & zapta if he si using TE110P thank you