similar to: 10 FXS - Channel Bank or PCI Card?

We will be connecting our Asterisk server to ISDN 30 and intend using the Sangoma A101 card. The install location is in London (UK). Sangoma card at Voipon http://www.voipon.co.uk/sangoma-a101-pri-isdn-card-p-132.html?gclid=CI32vJz22I0CFQXklAodIgjHaA I would be grateful to hear if this is the right choice of card. Usage reports would be helpful. Regards Rory -- Rory Campbell-Lange

Hi I have been having a rough time getting a Sangoma A200/Remora FXO/ FXS Analog AFT card set up properly. The main issue is that the card has four ports and as far as I can tell Asterisk is only seeing two. On the two that it recognizes the "Green" FXS ports are not green, they just are not lit. The "RED" FXO ports are indeed red, but from what I have read your not

Hello, I want to create channel bank in this case: "channel bank" |-----------------------------------------| | FXS,FXO<----->TDMoE<--|---------------------------------->Asterisk |-----------------------------------------| How can it?

I have a pair of Asterisk servers which are happily routeing VoIP calls. I want to hook one of them to the PSTN. Given that I am in the UK, what is a reasonably easily-available device to provide an FXO interface from a Linux box, with a minimum of faffing around with drivers? Just one line is needed, though in theory two might eventually be useful. My usual white-box hardware suppliers don't

Has anyone had any experience using FXO and FXS gateways to extend legacy PBX extensions to remote users? I have a customer who needs to do this, but wants seamless, two way communication, with a SIP server and without the need for 2-stage dialing. If anyone has any experience with a solution please let me know. Thanks Cory Andrews

----- Original Message ----- > Roger Burton West wrote: > > > I want to hook one of them to the PSTN. Given that I am in > > the UK, what is a reasonably easily-available device to > > provide an FXO interface from a Linux box, with a minimum of > > faffing around with drivers? Just one line is needed, though > > in theory two might eventually be useful. My

Folks, I have a TDM400 with an FXS module. I'm having some trouble ringing some phones attached to the device. I have a real el cheapo handset that cost me about 9UKP. It works fine, I plug it into the Wildcard and call the channel and it rings. I have tried plugging in my BT Diverse 3016 cordless phone but it will not ring, although I can call out from it. I have also tried my GPO 332L

Evening all. I'm looking at building an Asterisk system for one of the projects of the Charity where I'm the SysAdmin. The project has two analogue phone lines - BT Featureline Compact, we're in the UK - that I'd like Asterisk to handle. My current quandary is which FXO interface to use. I've been looking at the Digium TDM400P and Sangoma A200, which are similar prices for

Hi all, I bought a Sangoma A200 card from an online supplier and explained exactly what I wanted, 3 incoming phone lines to PBX and a life line (some where to connect a standard BT phone to the PBX incase the power goes, making the BT phone ring). I was told to order 1 x FXS module (2 FXS ports) 2 x FXO modules (4 FXO ports) However being a complete noob, I have connected the 3 lines to the

Hi there, I'm having some fairly serious asterisk problems, which seem to be spread quite liberally across all asterisk versions, I've tried 1.4.2, 1.6.0.10, 1.6.2beta4 and still had exactly the same problem with static and echo on the line when using the PRI interface. A little background: Server: HP DL145 G3 Dual Opteron 246 with 2GB ram and a brand new OpenVox D110P

Hi, got a Sangoma A200 with a bunch of extension cards and having real problems getting it to deal with a normal single BT line Symptoms are that incoming calls are fine. Outgoing calls ring the far end, BUT asterisk never sees that the call is answered (ie no message in the logs files saying so), as a result the remove end can hear the PBX side talking, but there is no audio back from the

Hi: I have a Sangoma A200 card installed in a server with two FXO modules and one FXS module. Analog sets connected to the FXS module have a "squeaky static" -- it's like static mixed with the sound of someone vigorously cleaning a window a few doors down. In other words, it's not a classic static noise, but it is noise, and it's distracting. Remote callers can hear this

Hi all, I have setup a Dell PowerEdge 2550 with a Sangoma A200 card with 2xFSO and 1XFS modules. The PowerEdge specs are 1 x P3 1133MHz, 512MB RAM. Sangoma A200 has 3 analogue PSTN lines connected. This server is based in Office 1, with 5 users all with a Linksys SPA942 VoIP Handset. There is another Office (Office 2) connected to here using VPN. There are two users in Office 2 with the

I just implemented a system using a TE411P hardware echo cancellation card. Per Digium, I setup zaptel.conf, and zapata.conf the same way as I always have. To my surprise calls out to the PSTN had a terrible echo. 1 - 2 second delay, and quite clear. The echo was so bad that I had to remove the hardware echo cancellation module from the card. We are only using the 1st span of this card right

Hi, I am using phpagi for agi scripting. and want to update callerid number but didn't get any success. please help me how to update PHPAGI is new for me. Below is the code which I write. #!/usr/bin/php -q <?php set_time_limit(30); //require(.phpagi.php.); include("phpagi.php"); $agi = new AGI(); //answer the call $agi-> answer();

Is there any advantage of getting a T1 card with a channel bank over 2-3 FXO cards ? Thanks. Dovid -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20061031/0f74ec67/attachment.htm

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all! I had the opportunity to test a Sangoma A200 card and I have some doubts that I would like to consult: I tried to detect the card and I had no success using the wctdm module with DAHDI. I guess this is because electronics is different because the TDM400P and OpenVox A400P cards have separate modules for each channel, while the Sangoma A200

Hi all, Just want to check from the list experienced personal about the Digium HPEC, where I had purchased the HPEC and wish to run with TDM card Sangoma A200. I can't install HPEC to run with Sangama A200 card, even I had changed my hpec file from i686 to i386. The error that I had as bellow; > Found key 'HPEC-XXXXXXXXXX' for 2 channels. > Found valid HPEC licenses for 2

As far as I can tell, after discussing this matter with other asterisk users in my area, my telco _does_ provide disconnect supervision.. It seems that the problem is actually related to the Sangoma A200 card I'm using, as two other people both using this same card have expressed the same problem.. Are there any other users on this list using the Sangoma A200 FXO port card, and experiencing

Hi - I just got a Sangoma A200 card with a single 2FXO module and what appears to be an empty module. I put the card in my Dell GX260, but the power light on the front of the box just blinks and won't power up. I did take the power cable from the CDROM to put on the card - I don't need the CDROM right now.. I'm looking for direction in getting this card working - I currently