similar to: hanguponpolarityswitch - where did it go??

I've just had polarity reversal provisioned by our telco to test hangup detect with a TDM400P I've set hanguponpolarityswitch=yes in zapata.conf When I start Asterisk I get "ignoring hanguponpolarityswitch" in /var/log/asterisk/messages I assume that the option is either not valid or conflicts with another setting somewhere. Any ideas?

Hy, I'm working with asterisk 1.2.4 and zaptel 1.2.4 With these version an the options in zapata.conf: answeronpolarityswitch=yes hanguponpolarityswitch=yes I don't detect polarityswitch. When asterisk reloads I see in CLI: May 10 00:44:27 WARNING[14639]: chan_zap.c:10876 setup_zap: Ignoring answeronpolarityswitch May 10 00:44:27 WARNING[14639]: chan_zap.c:10876 setup_zap: Ignoring

I have one TDM2404E digium card on asterisk box, after configuring the zaptel and zapata configuration files, I am getting these errors when reloading asterisk: ast_unregister_indication_country: Removed default indication country 'us' setup_zap: Ignoring signalling setup_zap: Ignoring answeronpolarityswitch unable to recognize channel 13-5 what is the reason for that? Thanks,

(Sorry of this appears in the list twice, but I wasn't sure if it was blocked or not) Hi there, I'm having a problem with my TDM-400P which has been working like a charm up until very recently. It started to fail last week, and so I was hoping someone could illuminate me with some information as to why. Its configuration is as follows: ------------ FXS (green) module is in position 1,

hi: In my zapata.conf i have 4 fxo configured channels,for fxo number 1 to 3 i added polarity reversal property but for fxo number 4 i didnt add polarity reversal property but it still giving me on cosole that fxo number 4 is polarized (because the line on fxo number 4 is not polarized). what i want to do is to not let polarity reversal take effect on fxo number 4. that what i have in my

Today I received a TDM11B (1 FXO and 1 FXS) and got it installed just fine. I bought the card mainly to get caller ID to work properly in Sweden, and that works just fine. However, if the called or calling party hangs up after I hangup my SIP channel, polarity CID detection kicks in and dials a couple of signals to my incoming context. This happens with Asterisk 1.0.6 and CVS-HEAD. I have tried

Hy, I'm writing from Spain. I have the 1.2.4 asterisk version and 1.2.3 zaptel version. I've heart that this asterisk's version detects correctly de hang up of PSTN, but in my case this thing doesn't happen. Moreover, my asterisk sends the next messages in the CLI: Feb 21 15:03:13 WARNING[10363]: chan_zap.c:10876 setup_zap: Ignoring signalling Feb 21 15:03:13 WARNING[10363]:

Hi Since Im using the mISDN drivers and no zaptel stuff, I had to install ztdummy to get MeetMe to work. Well, that was the plan. Now, after getting the latest zaptel version over CVS (Im using Kernel 2.6), uncommenting all the modules except ztdummy in zaptel.sysconfig file and compiling this by "make", "make install" and "make linux26", I rebooted and

When I reload the asterisk I get the following warnings: Oct 13 08:29:17 WARNING[10170]: chan_zap.c:10874 setup_zap: Ignoring switchtype Oct 13 08:29:17 WARNING[10170]: chan_zap.c:10874 setup_zap: Ignoring signalling Oct 13 08:29:17 WARNING[10170]: chan_zap.c:10874 setup_zap: Ignoring rxwink Everything works fine as far as I know, I can dial and complete calls. So why am I getting this

I reloaded my asterisk and found some red lines flushing by. When I stopped it I see: WARNING[21481]: cahn_zap.c:9773 setup_zap: Ignoring signalling WARNING[21481]: cahn_zap.c:9773 setup_zap: Ignoring echocancelwhenbridge WARNING[21481]: cahn_zap.c:9773 setup_zap: Ignoring echotraining Reconfigure channel 1, FXO Kewlstart signalling Reconfigure channel 2, FXO Kewlstart signalling

When I reload the config, I see this error in the CLI. However, I don't see what I have done wrong: == Parsing '/etc/asterisk/zapata.conf': Found May 30 16:38:42 WARNING[12630]: chan_zap.c:10088 setup_zap: Ignoring signalling -- Reconfigured channel 1, FXO Kewlstart signalling May 30 16:38:42 WARNING[12630]: chan_zap.c:10088 setup_zap: Ignoring signalling -- Reconfigured

Good day all We got a Wildcard TE110P I installed linux,zaptel,libpti and asterisk I coped over my zaptel.conf and zapata.conf from a previous E100P config But when I try to start asterisk it gives error not bying able to load zap channles: == Parsing '/etc/asterisk/zapata.conf': Found Jan 10 08:17:18 WARNING[-1084595552]: chan_zap.c:9308 setup_zap: Ignoring switchtype Jan 10 08:17:18

Hi all, I've just got an OpenVox A400P card with 1 FXO and 1 FXS module and I am just trying to get it working. But no luck as of yet. In /etc/zaptel.conf I've set the following options: fxsks=2 fxoks=1 loadzone=se defaultzone=se And in /etc/asterisk/zapata.conf I've not sure what to set exactly. For example, under [trunkgroups] what to specify there? Under [channels I set something

Hi all, I have a problem with the cvs head zaptel library: I cannot update my zapata.conf into asterisk when I issue the reload command from the CLI prompt; only when I stop and restart the asterisk service. The system sends the following message: Jun 20 09:49:14 WARNING[3754]: chan_zap.c:10364 setup_zap: Ignoring switchtype Jun 20 09:49:14 WARNING[3754]: chan_zap.c:10364

hi all iam using ztdummy driver after my call end , when i look at debug mode in cli i get this errors --- (0 headers 0 lines) Nat keepalive --- -- Reloading module 'chan_agent.so' (Agent Proxy Channel) == Parsing '/etc/asterisk/agents.conf': Found -- Reloading module 'chan_local.so' (Local Proxy Channel) -- Reloading module 'chan_zap.so' (Zapata

Hiya all, I have had no end of trouble trying to get my A101 E1 card working on a new asterisk installation. The sangoma tech people have ignored my emails about this. All the installation of wanpipe seems to go ok, and zaptel. it all installed compiled and does all the wanpipe hwprobe exactly as documented. Asterisk compiled ok, but when I run it give me Jun 27 11:12:18 ERROR[10528]:

Hi ! I have some issues, i don't know exactly if it's a busy detection issue. When i dial into the Asterisk box, and if i hang up before the Asterisk answers with the IVR Welcome message, the Asterisk goes on with the call. But, if i wait for the Asterisk to answer, and if i hang up, the Asterisk hangs up too. I have this parameters on zapata.conf: busydetect=no

Hi, I am using asterisk 1.4.28 with freepbx and Wildcard TDM410P card. Everything is working fine except the caller ID of incoming call from PSTN line. The phone display is showing "Unknown" when there is an incoming call. *My log file showing this while an incoming call on PSTN line:* tail -f /var/log/asterisk/full [Dec 30 06:36:16] DEBUG[2559] dsp.c: dsp busy pattern set to 0,0

Hello All, I'm trying to connect Asterisk to an Executone phone system with an analog DID card and I'm hoping someone can help me figure out what I'm doing wrong. The Executone DID card provides battery to the telco, when the telco wishes to dial a DID it goes off-hook, waits for a wink from the Executone and then dials the last three digits on the number with pulse (as opposed

Hi guys, I've been installing and configuring a TE110p card. The compile and install went very well. I'm using this on FC4 and I compile with linux26 as well checked I on the udev configs. zttool and ztcfg both indicate that the card is ready. But when I try to "load chan_zap.so" then I get the following Unable to load module chan_zap.so Jan 5 21:43:33 ERROR[6808]: