similar to: Line drops strange problem(got event On hook)

Hello to all, I post again (last time subject: Line drops strange problem(got event On hook) because i have caught in debug a situation where i get a call and the line drops and i get a call from the same caller and the line works well and the call normally closes by both parties. The only differences i find are underlined. If someone can understand the reason why the line drops from the debug

Hi, I facing a problem with flash hook. When ever I do a flash hook to place an extsing call on hold, the call gets disconnected. The debugs on Asterisk shows that 'on hook event detected' when I press the flash button on the phone. The setup is like this Asterisk box with T1 cards and FXS cards. The T1 card is connected to an IAD and configured for ISDN PRI lines. Analog phones come

I have been trying for some time now to make the hook flash work on the FXS port. I am using Asterisk 1.4.10.1 with zaptel 1.4.4. When I "manually" flash the hook I can manage to find the duration to put a call on hold. However when pushing the flash button it never works. The phone's flashtime seems to be too short. I tried to set a shorter flashtime in the zapata.conf file, but it

Hi all, what could be the cause for the following messages? May 22 12:44:53 WARNING[3791]: chan_zap.c:8498 zt_pri_error: 2 !! Got reject for frame 0, but we only have others! May 22 12:44:54 WARNING[3791]: chan_zap.c:8498 zt_pri_error: 2 !! Got reject for frame 0, but we only have others! May 22 12:44:55 WARNING[3791]: chan_zap.c:8498 zt_pri_error: 2 !! Got reject for frame 0, but we only have

Hi all, I have 1 Card Digium TE412P and 2PRI E1. I have more problems with drops lines. The asterisk log is this: May 16 10:52:26 NOTICE[4465]: chan_zap.c:8194 pri_dchannel: PRI got event: Alarm (4) on Primary D-channel of span 1 May 16 10:52:26 WARNING[4465]: chan_zap.c:2287 pri_find_dchan: No D-channels available! Using Primary channel 16 as D-channel anyway! May 16 10:52:26 NOTICE[4465]:

Hi all, I am seeing on my logs this message: Jun 13 09:14:51 DEBUG[4944] chan_zap.c: Monitor doohicky got event Event 160 on channel 3 Jun 13 09:14:51 DEBUG[4944] chan_zap.c: Monitor doohicky got event Event 160 on channel 3 (repeated much more then what I will show here). I see that it comes from static void* do_monitor(void *data) in chan_zap.c, but I do not understand what does it

HI I have two servers both of which get this message on one of the lines. Ring/Off-hook in strange state 6. The one server seems to be ok with it, but the other one when an extension picks up there is no one there and the incoming call keeps ringing. I tried to adjust the levels in wcfxo.c like someone had suggested, but it didn't do anything. I also upgraded zaptel to the latest. 1.2.18 and

I receive this error on the asterisk console and it is pretty much ALWAYS coming up. Sometimes there will be a break where it does not display. We had our PRI provider test the lines and they claim that there is no signalling problem. It doesn't matter if there are no calls or if there are 10 calls in progress the error is still displayed. I also get an annoying popping or clicking sound

Hi Guys, Running the following with a Sangoma A101D PRI card: *Asterisk 1.4.21.2* *LibPRI version: 1.4.10* No inbound or outbound calls can be made. In fact Asterisk CLI doesn't show any activity. Problem goes away on restart of the system or maybe asterisk. I see post about upgrading Libpri to 1.4.10.2 and then I see posts that even that didn't work. Anyone can weigh in this please?

Hi, Trying to trace an asterisk hang on a production (it had to be didn't it) system. The last thing before it crashed was [Mar 16 12:32:42] DEBUG[7754] chan_zap.c: Ignore switch to REVERSED Polarity on channel 1, state 4 [Mar 16 12:54:34] DEBUG[7754] chan_zap.c: Ignore switch to REVERSED Polarity on channel 2, state 4 [Mar 16 12:54:35] DEBUG[7754] chan_zap.c: Ignore switch to REVERSED

Hi all, i use asterisk 1.2.7 and i have a problem with callerid. i use sangoma a200 cards. one fxo one fxs module i have these scenario - bob calls adam, where bob calls into my asterisk and adam picks up "from" my asterisk - bob and adam are speaking to each other - meanwhile eve calls adam, adam hears a beep, and knows there is an other caller on line. - bob and adam stop seaking

Anybody else get theses warning? [Jun 26 10:08:55] WARNING[3158]: chan_zap.c:4747 zt_handle_event: Ring/Off-hook in strange state 6 on channel 1 PB

Asterisk version: 1.2.0-beta1 -OR- CVS HEAD Hardware: Generic X100P clone connected to Panasonic KX-TA624-5 extension port The problem happens IF AND ONLY IF: - the Panasonic is set to use double rings - the X100P is set to answer immediately (I'm using DISA here) It does not happen consistently; sometimes Asterisk behaves normally. When the "strange state" happens, DISA usually

I am getting: NOTICE[180235]: chan_zap.c:7358 pri_dchannel: PRI got event: 6 on Primary D-channel of span 1 on my asterisk box and it seems to be causing a poping sound in the phones, I am wondering if anyone can shed some light on this. I have scanned the archives and get possibilities ranging form motherboards, to pri, to loaded module problems. Can someone tell me the best way to start

I'm running asterisk 1.0.3 and seeing occasional messages on the asterisk console that say: Dec 18 09:09:55 NOTICE[26411]: chan_zap.c:7381 pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1 or Dec 18 09:25:46 NOTICE[26411]: chan_zap.c:7381 pri_dchannel: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 They don't see to have a noticeable impact

I recently purchased a TDM11B so I could hopefully hook flash the FXO from either the FXS (on the TDM11B) or a SIP device. From the FXS, I've tried hitting # then transferring to an extension that flashes the line then dials the FXS again (3020). This seems to send me to a busy signal and the console tells me no such host of 3020 (the number I'm on). The call on call waiting gets sent

All of a sudden I am getting the following warning "Ring/off-hook in strange state 6 on channel1" from chan_zap.c and I cannot answer calls. I can place calls out without a problem though. Any ideas what can be the problem. I have checked zapata.conf and zaptel.conf and they both seem fine. Thanks in advance. Dan -------------- next part -------------- An HTML attachment was

I also experienced this problem and the first thing that really helped out was changing the timing in the span line of the zaptel.conf. Change it to look like this (see below) and see if it helps out. I got the error much less after doing this and eventually got rid of the error completely by removing my raid drives, installing an IDE drive, enabling DMA mode on the Hard Drive, enabling APCI in

I've updated to the latest CVS as of today (and rebuilt RedHat 9). My setup is as follows: Wildcard X101P - channel 1 TDM400P - channels 2-3 - fxs cards with fxo signalling, channels 4-5 - fxo cards with fxs signalling I got CallerID to work on channel 4 with an old CVS, despite the usual "Didn't finish CallerID spill" message. However, as soon as I insert the following

I am new to Asterisk and the protocol/language complex world of VoIp and PBX. But I have a dedicated machine running A@H 2.8, a single TDM400P with one FXS module card connected to a standard analog phone. The second card is an X100P connected to my analog PSTN phone line. I also have Grandsteam IP phone plugged into the network and a couple of x-lite SIP softphones. I can make outgoing calls on