similar to: Analog FXO status checking

I installed Trixbox and a TDM400P with 2 FXO and 2 FXS ports and am having an annoying issue with the FXO ports. As soon as I plug either one into the phone line it's as though the line is disconnected i.e. get disconnected tone when trying to dial out, line is busy when dialling in. The CLI shows the following: trixbox1*CLI> zap show channel 4 Channel: 4 File Descriptor: 18 Span: 11*

I've been having trouble with making outbound calls to my TELCO from a TDM400 card (FXS KS signalling) after upgrading from 1.6-beta9 to 1.6.0. The problem is completely intermittent. When it fails, I get this message: [Nov 9 19:12:26] WARNING[18916] app_dial.c: Unable to create channel of type 'DAHDI' (cause 0 - Unknown) At some point, it starts working, but I don't know what

I have an Asterisk@Home 1.3 server (Asterisk 1.0.9) and recently added a TDM400P with (1) FXO card on port 4. Inbound calls are always successful but outbound calls fail 75% of the time with intercept messages from my dial tone provider that include "we're sorry, your call did not go through", and "we're sorry, when placing a local call it is now necessary to dial an area

OK... so I'm not sure what I'm looking at. I've had the good old echo problems on my Rev C FXO again this morning, so I thought I'd attempt some debugging, though I'm not sure what I'm looking at. This call has echo. Channel: 2 File Descriptor: 20 Span: 1I> Extension: Dialing: no Context: incoming Caller ID string: "External Call" <99999999> Destroy:

Hi, We are having a problem with asterisk detecting that an analog ext has been put down. This seems only to happen after a number of calls have been made. We have an FXO port (TDM400P with FXO module) connected to our PBX and are using this to test asterisk prior to rolling our for our small office. What happens is that we make a number of calls to this ext which 1st rings a phone (FXS)

Thanks Zeeshan, SAngoma told me that the asterisk problem is unrelated to wanpipe drivers, they told me to reinstall asterisk again But, i still having doubts about the problem :( Thanks in advance > > Message: 10 > Date: Thu, 18 Mar 2010 00:21:06 -0400 > From: Zeeshan Zakaria <zishanov at gmail.com> > Subject: Re: [asterisk-users] Asterisk DIES with no trace. PLEASE >

Happens quite often. X100P FXO card puts the PSTN line offhook, so that no calls go out or come in. The outside callers get a busy siganl while inside callers cant dial PSTN. Its a DELL optiplex P3 128MB ram 500MHz processor. Here is some more info: (see the zapata.conf in the end) Please direct me where to look for problem. Thanks!!! ======================================== pbx1*CLI> zap

Hi, Sorry to insist, but I would really like to be able to use Xen and my zaptel hardware all together in Dom0. I was just wondering if the 3.1 release could contain some changes compared to 3.0.4 related to IRQ handling or scheduling that could workout my problem. Thanks, François. ---- I actually first asked to asterisk mailing lists, and a few persons told me that it was Xen''s

Hello all: I upgraded to 1.4.3 last night and use MySQL for CDR. I have noticed that 1.4.3 seems to log a lot of "crap" to CDR that 1.4.2 did not. I use a few macros in my dialplan to handle outgoing calls (lcr type stuff) and in addition to the proper CDR for the call itself I also have records to 's' in the same dest-context and entries to 's' in the default context.

Hi, Lately we've noticed that some Zap channels on one of our PRIs are unavailable. We have 2 PRI lines with 60 channels in total. On the first PRI there are currently 20 channels that are not being used for some reason. I tried googling around and found some similar problems but there really was no solution (?). I'm not sure if this problem has occured now because of more load on the

I new in asterisk world so, please, forgive me if I say something stupid. At least, and after a lot of tryes, the isdn card seems to be registered: [chan_zap.so] => (Zapata Telephony w/PRI) == Parsing '/etc/asterisk/zapata.conf': Found -- Registered channel 1, PRI Signalling signalling -- Registered channel 2, PRI Signalling signalling -- Automatically generated pseudo

Hi, We have two of these 4 port FXO cards. However, we are having some problems with incoming/outgoing calls. The latest version of Asterisk/zaptel from CVS is being used. Voicemail, internal SIP <-> SIP calls between Pingtel xpressa hard phones work terrific, echotest is fine, and so on. The zaptel and wcfxs modules load fine, and show all 8 FXO interfaces in dmesg:

I have an Asterisk 1.2.16 server running CentOS 4.4 with a TE110P card and an OpenVox A1200P card. Up to today everything was working perfectly. The OpenVox card has 8 FXS and 2 FXO ports. The two faxo ports are used for a GSM adapter and for an ATA connected to Vonage. The problem we started noticing today was that the Vonage line will receive a call and then cannot connect to any of the SIP

Im having a problem getting the 2 cards working together. I added the TDM with 3 FXO and 1 FXS board. The TE405p is working fine. THe TDM registers and identifies the FXO's and FXS but cant get them to go off hook. I hope someone can help. Asterisk seems to THINK its dialing it sends manager status as dialing, and it just sits there with no tones, on the phone dialing out. If I dial,

Hi, I'm trying to make a dialup internet connection through my asterisk PBX. When I bipass the Asterisk box, I can get 51600bps. When I run through the asterisk box, I'm limited to about 21600bps. I have a TDM31B card. Any help on speeding these connections up would be good - I was on the understanding that if you bridged the channels, then the call should essentially flow straight

Hi guys, This has been bugging me for days and I can't figure out what's happening. Using the same channel on DAHDI, I can't make a call after previous one being hung up by remote side. However, it works like it should if my end hangs up the call. To make things interesting, DAHDI, or astribank rather, seems to "reset" itself after receiving an incoming call on that DAHDI

I'm looking for a good, reliable, and cheap 4-port FXS ATA. Does anyone know of one that works with Asterisk? Thanks, Waldo

Hi I have the X100P card which as to sockets (LINE - for fxo line ) and PHONE (to connect a n analog line) This card is setup as fxs_ks I was getting dial tone but suddenly no Dial Tone....Help appreciated.... When I try to route the Call using - Dial Zap/1) to this FXO Line I get this error: ------------------------------------- linux*CLI> -- Executing

I have echocancel=yes in zapata.conf but when I do a zap show channel 1, I notice echo cancellation is turned off. I followed the article that talks about the order in which the statements need to be in zapata.conf to get echo canceling to work: http://lists.digium.com/pipermail/asterisk-users/2005-June/110615.html But it is still not working. Does anyone know how to get echo

Hi all, I just posted this question before last week. Meanwhile after upgrading Asterisk 1.0.7-BRIstuffed-0.2.0-RCg to 1.0.8-BRIstuffed-0.2.0-RCh the same problem occurs, but seems to be more seldom. Attached is now the output of "zap show channel" . - I'm running a stable Asterisk on a HP DL380G2 1.4Ghz 0,5GB RAM equipped with 1x TE410P and 2xJunghanns OctoBRI running in NT-mode.