similar to: Echo problem with TDM440P and ADSL Line

I'm using bristuffed Asterisk with ISDN/ZAPHFC I have VERY ugly (outgoing) sound through ISDN/HFC if echocancel=yes in zapata.conf, but without echocancel I have bad (incoming) echo Through PSTN/FXO sound is ok with or without echocancel. I tried other echo cancellers (in zconfig.h) two times: ECHO_CAN_KB1 (this was default) ECHO_CAN_MARK2 ECHO_CAN_MG2 after any change I compiled (make

Good Day all, I have a Fractional PRI connected to my Asterisk Box via a T100P card. When I initiate a call out to phone number 123-8888 the call sounds great no echo what so ever. If the person at 123-8888 hangs up and calls me right back (same handset on both sides) same trunk line The call always has echo on it. The Asterisk sip extension hears them selves echoing. The remote party

Is anyone aware of an milliwat/echo test number for telstra or similar? I want to fiddle a bit with gains but can't seem to get a hold of a miliwatt test number Im aware of a number they distribute for line quality testing for modems for BigPond, but I can't track it down .... -- Adrian Carter Technical Manager Leading Edge Internet Web http://www.lei.net.au http://support.lei.net.au

Hi there, I've asked this question to the BSD group too, but I'd like to know whether anybody else had similar experiences on Linux 2.6.20 etc.?? FreeBSD 6.2 Asterisk 1.4.5 (and 1.4.3 from ports) Sip phone - PBX(*) -IAX2-VROUTER(*)- SIP-Voip provider (SPA901 & SPA922 phones) We've see a situation where the IAX2 appears to "loose"/drop the voice data to be sent to

Hello everybody, I am sorry to bring this up again if this kind of echo issue has ever discussed. Phone2 in below call path experiences quite annoying echo: Phone1 --> FXS (TDM400P) --> Asterisk --> SIP GW --> PSTN --> Phone2 It is annoying as on phone2, we can hear the whole words we say with the level of maybe 25% of the original sound. I can reduce the echo to maximum with

>Message: 26 >Date: Sun, 15 Jul 2007 07:59:09 -0400 >From: Dan Halbert <halbert at everyzing.com> >Subject: Re: SOLVED: Re: [CentOS] Newbie ADSL configuration, ppp0 > can't activate & config not found >Message-ID: <469A0C0D.3030400 at everyzing.com> >Great! By the way, you should not even need to specify the DNS >servers. >In the DHCP

A few days ago I wrote complaining that my new, cheap Compaq Presario (sr5010nx) could not create and maintain a dsl connection using Centos5. I was puzzled that that Ubuntu - with pppoeconf - would work just fine but Centos5 could not be configured. (cento4 -also) Eventually I googled and found a bug report for the r8169 Gigabit ethernet driver. Conclusion - there is a patch in new kernels

Hi all, I have this Fedora 7 system with 3 ethernet cards, eth0 servicing the local network, eth1 connected to ISP1 and eth2 connected to ISP2. I''m only using ip routing and my ip tables are currently empty. no other firewall seems to be running - unless I''m not aware of it. I have managed to use the connection to ISP1 for all internet connection, but failed to use ISP2 at all!

Hello! I read the Split access and Load balancing sections into LARTC (Chapter 4). However I have one gateway only and the LARTC says about 2 links. I need to know how to make a load balance with my links. Thanks in advance. Eriberto - Brazil

anyone know how to use tc and rrdtool to create queue based graphs? im currently using http://www.adsl-optimizer.dk/ADSL-optimizer, of which the ddraw.cgi doesnt work properly on debian testing. im looking for graphs like this: http://www.adsl-optimizer.dk/graph-shots/12hours/ if anyones done this with adsl-optimizer, or has any suggestions where to start with creating graphs like this, then

hi all, I have a firewall with 2 gateways. Router A (main, adsl), router I (backup, isdn). In case of failure of adsl I switch to isdn. How can I know when it is time to go back? Which is a standard way to test the adsl line? TIA sandro -- Sandro Dentella *:-) e-mail: sandro@e-den.it http://www.tksql.org TkSQL Home page - My GPL work

Hi all, Below is my network diagram: - eth0 (adsl 1) eth1 (adsl 2) | | | | | | | | ----------------- | | | Gateway | | | ----------------- | | | tun0 Below is my iptables scripting to mark certain ports: -

Hello, how it''s possible to download something from ftp servers without site-to-site transfer enabled? If the data transfer connection will be routed through another outgoing interface than the command connection the server denies the connection. Are there any solutions for instance with ip_conntrack_ftp module or similar? -- Markus Schulz

I hadn''t seen this site mentioned before. Interesting paper on effects of ADSL on bandwidth management http://www.adsl-optimizer.dk

hi all. First of all, sorry for my (bad) english. I Want to balance the traffic in a local network over two ADSL. I wanna send http traffic trough ADSL line number 1. And the other traffic by the default ASSL (number 2) Can you help me ? thx. _______________________________________________ LARTC mailing list / LARTC@mailman.ds9a.nl http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO:

Hello, I''ve setup a box, to balance traffic beetween a cable modem and an adsl, i''ve installed fedora core 2 in the box, then downloaded kernel 2.6.7, applied Julian Anastov parches for version 2.6.7, and then when i tried to compile the kernel i got and error about variable rt not declared, so i check the patch and saw one of the thing it changes is getting rid of line 84 of

https://www.p2pwatchdog.com/ > -----Original Message----- > From: lartc-admin@mailman.ds9a.nl > [mailto:lartc-admin@mailman.ds9a.nl] On Behalf Of Roy > Sent: Thursday, September 02, 2004 5:04 AM > To: Ing. Marcos Salvatierra; James Lista > Cc: lartc@mailman.ds9a.nl > Subject: Re: [LARTC] adsl and p2p programs > > This is most asked question but there is no good

Hello, Is there a sample-configuration for users who which have "PPTP Client running on your Firewall with PPTP Server in an ADSL Modem" Where can i find this file as described in the document? "If you have this type of setup, you need to modify the sample configuration that you downloaded as described in this section." Thanks, borsti

Hello, I would like to know if it is possible to have multiple ADSL connections going into a box running shorewall be pooled into one connection. IE: shorewall is a gateway/firewall for a server and have the server obtain double the speed to the net by "splicing" both ADSL connections into one. Regards, Justin Lorne Kaufman

+1 This message posted from opensolaris.org