similar to: CAS DID 2way

I have posted this to the Asterisk Forums, but got no response yet. Sorry if you are reading this for the second time. What fax hardware do I need for a T1? Ideally, I will switch my T1 to a digital PRI (not CAS I'm told, which is not as good) coming into the building. My CLEC said I can do this switch no problem. I have an analog T1 coming in now. >From the Asterisk box, I will connect

Hello, I'm trying to make my asterisk box to act as a telco, in order to reproduce a US environment in europe. Our telco provider is giving us those settings: ESF B8ZF Inbound = E&M Immediate Outbound sig =Wink Start Yield to Glare = Yes Those trunks are using CAS for signaling. I have tried many configs/combinations in zaptel.conf and zapata-channels.conf In zaptel.conf, when having

I'm looking to install a system with 80 FXS analog phones. At this time the only cost effective solution is using a 4 port T1 card and addit 600 channel bank. Has anyone tried this solution? any good documents beside http://www.voip-info.org/wiki/index.php?page=Asterisk+hardware+channel+bank+check as far as i know, addit 600 T1 interface is not PRI (please correct me if i'm wrong) its CAS

Dear All, I'm integrating avaya commuication manager difinity ver 1.0 with asterisk using B2B E1. following are the details of my H/W, zaptel configs and software installed. Digium TE110p asterisk 1.2.19 cent OS 4.4 zaptel 1.2.18 libpri 1.2.4 etc/zaptel.conf span=1,0,0,cas,hdb3 bchan=1-15,17-31 dchan=16 when i ztcfg -vvv im having this error message and the E1 is not getting up. "cas

Trying to find my feet here. If I wanted to connect Asterisk to a PRI and throw in a T1 Adtran channel bank into the mix for fax machines would the following work? Connect PRI line from telco to Port 1 on the Digium Wildcard TE205P. Connect Adtran TA-624-T1 to Post 2 on the Digium Wildcard TE205P also, would I need a crossover to the channelbank or is it a patch lead like the connection to the

Hello All, I was wondering. What are the primary advantages to using a PRI over a T1? As I understand it, the PRI terminates very fast, meaning you can do immediate answer and dial... This is very handy on the BRI line I have on the asterisk. Can T1 signalling also do immediate answer, or does it just behave like a channelized pots line and ring as usual? I am trying to determine if I should

hello my friends, when i make a genzaptelconf i get this message ******************** CAS signalling on span 2 conflicts with HDLC with FCS check on channel ******************* Any idea Please? I m installing zaptel 1.4 i checked in "http://bugs.digium.com/view.php?id=7860" that it's a bug but beacause i m a newbie in asterisk i can't undrestand what exactly mean Thank You

I want to replace a custom PBX, that is infront on a IVR system based on OLD NMS AG-E1 Card. The Cards is configurated with CAS Digitalmode, someone can give me some info about Digim Cards CAS configuration i need a conversion Table? I wanto to don't touch configuration on winbox, i want only replace HWPBX box with asterisk. Diagram Telco E1 ===>Proprietary PBX========(CAS)===>IVR

Below you will find, what I believe to be a typical setup with a T100P card. My question is - 1. Is this correct? 2. What kind of phones would be needed here... (Would you have to use Digital phones) And if so what would you recommend. PRI/T1----- | | | ---------------- | | | Channel Bank | | |

I have a ton of Nortel MICS/CICS phone systems and am looking for an easy way to integrate them. Two questions arise: 1. Is it feasible to use asterisk as a Man in the Middle for a T1 PRI system? The idea is to intercept outbound calls from the Nortel PBX and redirect them via VoIP to another asterisk box at another branch transparently(thus saving the LD cost). Otherwise I'd pass

All, I have done research on VoIP for some time now. I'm a Cisco certified Network Engineer however Telecom is not my strongest suit. I've been a part of this mailing list for sometime but my delusions of grandeur in migrating our 25 year old phone system to a new platform have been on the back burner, until now. I have found my company is moving to a new location(building) and this

Ok, I'm about to take the plunge, and am trying to decide between Channelized T1 E&M and PRI. I'm getting an "Integrated T1" which will have data and voice capability, all plugged directly into my digium single T1 card. In either case the data piece looks pretty straighforward, just setup the channel properly, hand it off to the linux hdlc layer, and route away.... the

I just tried to go from CAS to PRI on my T1 (Sangoma), and failed pretty badly. Seemingly everything worked -- Asterisk would see the incoming call (including CID and DID info), try to route it, and fail -- giving me a telco (not Asterisk) call failure message. My zapata.conf and zaptel.conf files are at http://pastebin.com/558349 Below's the log dump. Note that, because I was simply going

Hi all, I have seen the term E1 and PRI used interchangably when referring to a voice service with 30B channels and 1 D channel. Are they just different terms for the same thing or is there some technical difference. Even Newton's telco dictonary seemed a bit fuzzy on this topic. I have seen it said the PRi is a protocol that runs on top of E1. Is this true?

Hi guys, I posted a somewhat similar question about a month ago and got a thoughtful resonse from Steven Critchfield, but I've got a quick follow up question to it. I'm looking to setup a 16 extension / 10-14 phone line Asterisk install for a customer who would like to have DID numbers for the extensions, since they're currently on Centrex and already have the 1-to-1

Hi All, I'm having problems trying to get a TE120P operational in Canada. I keep getting a congestion error when I try to make a call. I'm not sure if my switching, parity, etc is correct. I'm hoping that someone will be able to verify my config. The Telco is SaskTel, with a 10 channel 50 DDI service. Zap show channels show and ztcfg -vv looks ok and the zttool show

Hi all, Muppet from the UK asking for help We are just about to have a T1 line installed in our office in Dallas and "Advantex" the supplier has sent a questionnaire asking a number of questions. I have put the question area at the bottom of the email, we will be using Digium's hardware. could anybody help :-) In the UK when I asked for a E1, number of trunks required and the

Hi all, This is a NEWBIE question, so all you experienced types that are tired of stupid questions can move on... I've pretty much given up trying to do my entire phone system over IP (including local service), so I have to select and provision my local CO lines. I need about 10-12 lines which can be POTS lines, of course. But, I thought, why not get something digital and expandable