Displaying 20 results from an estimated 3000 matches similar to: "0 channels configured with tdm400 (tdm04b rev. G)"
2006 Oct 30
3
Grandstream ATA 286 tdm400 and Asterisk 1.2-13
Hi people,
I would like to read your suggestions as to where the issue might be.
ATA286=Grandstream Budgetone ATA 286 in SIP mode. One Lan Port and one FXS port.
TDM04B= 4 FXO signal fxls
There is a 8FXO-to-SIP unit in this scenario that works perfectly so i
will not make mention of it.
PSTN----VOIPprovider---Internet---ATA286------tdm04b---Asterisk1.2.-13
Asterisk is being used as a meetme
2003 Oct 07
5
auto 'modprobe wct1xxp' on startup?
Hi guys,
Thanks for your answers on my two questions yesterday. That's exactly
what I was looking for, sorry for not noticing it myself, but I'm still
getting acclimated to Asterisk and even Linux--from what I see so far, I
love it.
I've got another one now. Since my Asterisk install and configuration
is fairly stable at this point, I'm interested it ensuring that during
2005 May 02
4
DELL 2800 : PCI Parity error
Hi,
I am struggling to get rid of a conflict on DELL 2800 : PCI Parity error
(EB113 on the display)
I am learning linux and asterisk as I go along, there might be obvious
things I should know, but bear with me.
>From demsg below my 2 digium cards installed are listed (no config or
connections done to digium cards yet), the conflict is with the TDM400P
card, without that card, in any slot, no
2005 Sep 06
7
Cookbook receipe for SCSI tape install requested.
I need to install an HP Surestore dlt on a Centos 4 machine and I
am at a loss as to how to proceed. Can someone either provide or
point me to an online reference on how to proceed to add and
configure a SCSI adapter and tape drive. I have read, but not
really understood, the man page entry for st. Does kudzu handle
this?
Regards,
Jim
I am a digest subscriber so the favour of an
2005 Jun 20
1
How can you check that eg TDM04B hardware installed and drivers OK
Hello
I am struggling to get my TDM04B working. Just to rule out a hardware problem how can I check that the hardware works? How can I then check that the drivers are loaded correctly?
Angus
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050620/470458c6/attachment.htm
2006 Mar 14
1
Controller detection order
Hi,
I have a dell poweredge 850 with centos 4, freshly installed. I'm now
trying to add in a fibre -> sata raid enclosure with LSI HBA's in the
850.
My problem is the enclosure gets detected first, hijacking sda and
sdb from the internal SATA drive and causing kernel panic at boot
time. I've tried changing the order in modprobe to the following:
alias eth0 tg3
alias eth1
2004 May 03
2
Number of Digium cards in one box...
I know, I know, check the archives but I can't find an answer since the
new cards are well, NEW!
I understand the whole issue of expandability and flexibility of using a
T1 card and an Adtran 750. FXO or FXS, you mix and match.
With the new card offerings from Digium I can easily put a 4CO by 8
Station system together.
Barring the extra interrupts, extra CPU Cycles of extra interfaces, is
2007 Jan 24
2
Disconnected Calls
Hello.
I am running asterisk 1.2.14 on a Dell poweredge with a Digium FXO/FXS card
connected to 6 analog lines and using Linksys spa942 phones.
My users are complaining of randomly disconnected calls, and when I watch
the log (debug warning,notice,error), I don't see any cause. It looks like
asterisk is seeing a hangup from the analog end.
I have attached my zaptel.conf and zapata.conf.
2004 Dec 23
5
TDM400 success?
Has anyone had success with the TDM400 in production? I have multiple
boxes where these cards lock up and the only thing that will fix them is
to unload *, modprobe -r wctdm, modprobe wctdm, load asterisk. Does not
matter if it is a FXS/FXO module.
I know this topic has been discussed many times before, but my questions
is not "is anyone else having this problem" since I know that
2005 Jan 24
2
Wildcard TE405P and TDM400 - TDM not working
Im having a problem getting the 2 cards working together.
I added the TDM with 3 FXO and 1 FXS board.
The TE405p is working fine. THe TDM registers and identifies the FXO's
and FXS but cant get them to go off hook.
I hope someone can help.
Asterisk seems to THINK its dialing it sends manager status as dialing,
and it just sits there with no tones, on the phone dialing out.
If I dial,
2007 Nov 28
1
Fw: Remove a TDM Card
Hi, sorry for my insistence but this is a big problem for me..my steps for
remove card are ok ?
Thanks.
------
Salvatore.
----- Original Message -----
From: "Sasa" <sasa at shoponweb.it>
To: <asterisk-users at lists.digium.com>
Sent: Monday, November 26, 2007 4:25 PM
Subject: [asterisk-users] Remove a TDM Card
> Hi, I would like remove a Digium TDM2400P from
2006 Sep 07
6
Restarting mouse services
I move my notebook around my office. Sometimes I am using the internal
pointers, sometimes a USB mouse, and sometimes a USB keyboard/mouse
adapter that is plugged into a kvm (actually two of them).
With one of these USB k/m adapters, when I plug in, the system fails to
recognize the mouse (but no problem with the keyboard). The 2 adapters
are the same brand/model (Aten), but the KVMs are
2004 Dec 30
0
TDM04b failures (xpost on purpose)
System: RHv9 cvs-head-11/23/04 with TDM04B and T100P (isdn pri).
We've all seen many posts over the last several months regarding
the stability of the TDM card. Today, the above system's TDM04B
card (4 fxo ports) failed at approx 15:54:49.
[root@asterisk asterisk]# cat /proc/zaptel/2
Span 2: WCTDM/0 "Wildcard TDM400P REV E/F Board 1"
25 WCTDM/0/0 FXSKS (In use)
2004 Nov 27
3
How to test if PCI 2.2?
Is there a way to test if the motherboard is ready for a Digium card
(PCI 2.2) ?
I would like to know from a remote computer, where I have (root) access,
if this computer is ready for a TDM22B.
bye
Ronald
2005 Aug 16
0
What should my next steps in troubleshooting this TDM04B error be?
Hello
I have installed a TDM04B and disabled any devices not required in my PC.
(TDM04B is analog card with 4 ports to plug into telephone co lines). I am
running this version of *
Asterisk CVS-HEAD-01/10/05-02:11:15-AstLinux built by root@ls on a i686
running Linux
As you see below the wctdm module is loaded:
pbx root # lsmod
Module Size Used by
binfmt_misc 12296 1 - Live
2009 Sep 27
3
Problems with Digium TDM400 card
I had a working Asterisk 1.4.24.1 installation on SUSE 9 Linux but SIP only. I then downloaded and installed latest Zaptel and could not get Zaptel working. So I downloaded Asterisk again and re-installed.
But still problems:
Here is my ztcfg output:
asterisk:/etc/asterisk # ztcfg -vvvvv
Notice: Configuration file is /etc/zaptel.conf
line 4: Unable to read Zaptel version information.
Zaptel
2005 Jan 05
7
TDM04B vs Dell
Hi all,
I've struggled for several days trying to get a Digium TDM04B 4-port
wxfco card working on a Dell 1U PowerEdge 750 machine running
Fedora Core 1. I finally got a call back from Digium who indicated that
there is a fundamental conflict between the card and the PowerEdge
having to do with PCI interrupts. Asterisk version is stable v1-0 12/29/04.
The symptoms of the problem were as
2010 Mar 07
5
dahdi-2.2.1 & kernel-2.6.32: working for anyone?
I have a TDM400. Just updated Fedora 12 to kernel 2.6.32. Rebuilt and
installed dahdi-2.2.1.
kernel modules loaded.
lsmod | grep wctdm
wctdm 37233 0
dahdi 194985 1 wctdm
lsmod | grep dahdi
dahdi 194985 1 wctdm
crc_ccitt 1549 2 dahdi,isdnhdlc
dmesg:
dahdi: Telephony Interface Registered on major 196
dahdi: Version: 2.2.1
2008 Jun 06
1
Asterisk not picking up incoming calls from TDM400P
Hi,
I am having some issues with a new server install in Singapore.
Outbound calls work fine.
Inbound calls are not picked up by Asterisk.
Zaptel 1.2.25 and Asterisk 1.2.28 both built from source.
libpri installed
wctdm and zaptel load without error
Jun 6 23:34:03 fs01 kernel: [211138.372933] Zapata Telephony Interface
Registered on major 196
Jun 6 23:34:03 fs01 kernel: [211138.372937]
2006 Jan 09
2
TDM400 (TDM11B) configuration
I have fixed this before, but I cannot for the life of me remember how I did it.
I have a TDM400P with one fxo module and one fxs module. I setup
Asterisk @Home and everything works fine, except when I try and call
out. If I call out with a SIP phone it calls the zap extension and
not the pstn line? If I take the zap extension offhook and call with
the SIP phone it dials out the pstn line