similar to: Motherboard Selection For TE110P & TDM400P

I've been working with Digium, but hopefully someone on-list has an idea... The card will transmit audio to the T1, but everything it receives is completely unintelligible static (in place of received audio only, not all the time). I've verified everything on Digium's troubleshooting checklist and they were unable to find anything when they logged in. zttest yields 100% for the

Fedora Core 6 regards, Pablo. On Thu, Mar 08, 2007 at 05:01:15PM -0800, Jose Bertuzzi wrote: > Hello Everyone, I checked with zttool that sometimes after the machine boots the order of the boards is changed like this: > ??? Alarms Span ??? OK Digium

Hello Everyone, I checked with zttool that sometimes after the machine boots the order of the boards is changed like this: ??? Alarms Span ??? OK Digium Wildcard TE110P T1/E1 Card 0 ??? OK Digium Wildcard TE110P

Dear users. My current setup uses a euroISDN E1 with 8 cahnnels for incoming and outgoing calls from a digium te110p. Currently all phones use SIP. However, I need to add some faxes lines and some POS credit card machines. These will require POTS lines with a fixed DDI. I have purchased the tdm400p and 4 FXS modules. My problem is with the zaptel.conf and zapata.conf. I am a little confused as

I am having a problem with asterisk not being stable enough for production use. I have two cards, the digium TE406P, and the TE410P. The TE410P is the primary card that I am using but I would like to move to the TE406P for the echo cancellation and more flexibility of PCI slots available. General config info: 3 PRIs, configured as such: span=1,2,0,esf,b8zs span=2,0,0,esf,b8zs

Hi all, I've setup a PBX in production environment last week but we have immediatly find out drop conversations and lot of errors (in asterisk logs) like: Apr 10 17:30:48 NOTICE[25154] chan_zap.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 2 My configuration is: Motherboard: SuperMicro P8SCT (Intel E7221 chipset) Hypertrading and APIC enabled CPU: P4 3GHz Digium TE205P

Hello all. I have here a TE110P (configured as E1) and a TDM400P (with four X100P - FXS). Both boards are recognized by the operating system as showed above: 0000:08:00.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface Subsystem: Unknown device b1d9:0003 Flags: bus master, medium devsel, latency 64, IRQ 169 I/O ports at e800 [size=256]

Hello all..... I would like to know if anyone here has had good experience with this Supermicro motherboard.....http://supermicro.com/products/motherboard/P4/E7221/P8SCT.cfm I am thinking about using it in an entry level mail and file server with a 3ware card and 200 GB SATA drives. Cost is a factor here otherwise I would go for an Opteron board instead. JC

Does anyone know if patlooptest either doesn't work for fxo/fxs signaled channels or if you have to do it a different way? If I run ./patlooptest /dev/zap/25 60 with a config like: fxsks=25-32 fxoks=33-48 it gives me a bunch of output along the lines of: (Error 4071): Unexpected result, 254 != 255, 11 bytes since last error. (Error 4072): Unexpected result, 0 != 255, 1 bytes since last

Hi List. I'm running the patlooptest program I've found in dahdi_tools 2.1.0.2. The target is a TE121P board with a loopback cable inserted on the socket. I suppose that the loopback is working fine because I'm able to see the green led on and dahdi_tool reports no errors. When I run the patlooptest I've a lot of errors (the received values are completely different than the

Hi there, Running patlooptest following instructions on Digium KB, using dahdi 2.5.1 with a TE205P. I'm getting this kind of output (not full output). Note, I'm using a standard cat5 ethernet cable (30cm), with a Digium T10i crossover. Error 4985 (loop 19898, offset 425, error 214): Unexpected result, Read: 0xff, Expected 0x00. Offset 422 { ff ff ff ff ff ff ff } Error 4986 (loop

Can anyone help and point me in a useful direction. I'm using * 1.2.4 with Zaptel 1.2.4. I have a TE110P card and it's a Supermicro P8SCT mobo. If I run the PRI card in the PCI-X slot it shares an interupt with eth0 but I don't get problems. I've been trying to move it onto it's own IRQ, by moving the card to a regular PCI slot but I now get the errors Mar 2 08:43:09

I had trouble with a TE110P card in a Supermicro mobo - P8SCT. The PRI line kept dropping calls when the card was in a standard PCI slot. In the end the only way to fix it was to install the card in the PCI-X slot. -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Matt Roth Sent: 22 September 2005 21:31 To:

Does anyone know if you can have multiple TE110P cards in one chassis? -Thermal -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20061011/adbceeb5/attachment.htm

Hi All, I have configure my Asterisk as follow (using Asterisk@home): [zaptel.conf] span=1,1,0,ccs,hdb3,yellow bchan=1-15,17-31 dchan=16 loadzone = uk defaultzone=uk [zapata.conf] [channels] switchtype=euroisdn pridialplan=local prilocaldialplan=local internationalprefix=00 nationalprefix=0 usecallingpres=yes busydetect=no ; not need on pri callprogress=no ; was yes but wiki says experimatley

Hi, thank you for last info. we've tried to use te110p but failed. We're quite surprised that cable wasn't included with the card as any documentation, at least on HW setup and installation, yet cable pinout for connection to PRI interfaces.... 1. We have followed instructions on your site and from Beronet guide, but card just keeps blinking and nothing happens (also no useful

Hi everybody, i need someone to tell me the spins numbers of Rx+,Rx-,Tx+ and Tx- of TE110P and also if you can tell me have to made a cable like that?? Modem Teleco <-----------Self Crosscable------------>Asterisk Rx+ <--------------------------------------------------------------> Tx+ Rx- <--------------------------------------------------------------> Tx- Tx+

Hi folks, I've already searched the mailing list but no one else seems to have my same problem. I'm using Asterisk with the following configuration: Fedora Core 4 (but I also tried Fedora 3) 1 Digium TE110P 1 TDM40B 1 HFC-S 'Cologne' bristuff 0.2.0-RC8o (zaptel 1.0.9.2) I compiled right, I can load kernel modules but when I try to unload wcte11xp module (the one

I have a Digicom TE110p card installed in our exchange. I have compiled and installed libpri, zaptel and recompiled and installed asterisk. I have configured udev as I am running Fedora Core 3. The problem that I have is that when zaptel is not running everything works fine. However when I start zaptel (service start zaptel) then I can make normal calls ok but the 'Playback()'

i get this message with a red signal on TE110P card: ***************** TE110P: span configured for... Calling startuo (flug is 4099) wcte1xxp: Setting yellow alarm ***************** what does mean ? thank you :)