similar to: No "ringing" being played to remote caller?

Hi again, I'm trying to setup our non pri T1 (they call it a Long Distance T1), our current pbx has the signaling set to E&M, I can set em in zapata.conf, but I'm trying to track down the proper entries for the zaptel.conf file. The digium docs only show a PRI example. Our current system has these settings: Signalling: E&M Framing mode: ESF Line Coding: B8SZ here's my

I have been getting quite a bit of PRI Resets using my Quad PRI Digium card. Prior to the resets I am getting similar notices to the following chan_zap.c:7482 pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 3 Telco claims the PRI's are fine on their end and that it is my unit. Is this timing? (google somewhat leads to this) I am running 1.08 asterisk zaptel

Hello all. I just received a TE110P and am trying to hook it to my Mitel 200SX has anyone successfully done this? My configuration is as follows. Asterisk -> TE110P ->Kentrox (csu/dsu) -> Mitel T1 Card. All I get is a blinking yellow on my TE110P card and an alarm on my Mitel. T1 card. Any advice would be great. Zaptel.conf span=1,0,1,d4,ami e&m=1-23 dchan=24

Hello, I'm trying to set the 3rd span of a new digium quad card as a E&M T1 for Faxes to a Hylafax server. The 1st and 2nd spans are working as PRIs. When I start asterisk, the logs show a signaling error and chan_zap.c dies. I also get an error that it can't read the gains but they are the standard shown below. 2.6 kernel, Debian Stable, * 1.2 svn from feb 2007 my procedure: make

Hi all I have a server that has two TE412P (T1/E1+DSP) cards installed. One of them configured as an E1 PRI connected to PSTN and another one configured as a T1 E&M connected to Avaya PBX. Each card only uses two ports, so there are 2 E1 lines and 2 T1 lines connecting to this server. The purpose of this server is as a TDM trunk gateway that gets call from E1/T1 and then forward to an IP-PBX

Does anyone have any experience getting a Mitel SX-200 EL/ML PBX system to work with *? I'm not getting inbound or outbound calls to work. (Inbound caller gets line busy tone.) SETTINGS FROM MITEL: I built a Crossover cable and connected it like this: PSTN--T1--ASTRISK--T1--OLD MITEL -Crossover Cable Pin-out: 1 - 4 2 - 5

Hello, I have a T1 (not PRI) plugged into my Asterisk server. Everything is working well, except I only get the first digit of the 4 digit DID in Asterisk. The T1 provider (Eschelon) tried switching to 7 digits, and I only got the first digit of the 7. Can anybody help? We're adding another DID and I need to trap it correctly. Thanks. Here are snippets from the relevant files: --

I know this topic has been covered before - I just want to make sure I am understanding this correctly. | ------------------- | | | | T1 | Channel Bank | | ----------| | | | T1 Cross | | | | | | | | ------------------- -------------- | Asterisk | | | |

Hi, Can I make e&m wink start lines just wait for digits - instead of going to default? Someone else cleared a similar problem (as described below) on an fxo port with "usecallerid => no" but it is not doing the trick for me. In this case the line when straight to default which would be ok also. John I posted the stuff below about a week ago... I set up a t1 from my sys75 to

How do I setup my T1 card as an E&M tie line? Any special configuration? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050523/8aac4dbf/attachment.htm

I have a Toshiba DK424 connected via T1 E&M to a TE110P card. Intermittently when a user dials a number I am getting 'getdtmf' errors on the Ast server and the calls do not go through. If they dial the number once or twice more, it works fine and I receive no DTMF problems. On another note, end users are complaining about intermittent disconnects. T1 is ESF/B8ZS - 24 chan. Other

I am trying to make an in/out trunk group comprised of 4 DS0's using E&M Wink signalling. The first four channels of a DS1 on a T100P are being used for the group. Outbound calls work fine, but inbound calls fail. The other 20 DS0 channels are used for a PRI. Does the configuration shown below look okay? I've tried setting 'immediate => yes' without success, but it

I have about a dozen SIP phones up and working, now I want to connect the asterisk box to our Fujitsu 9600 PBX. I currently have two dial-up servers conencted to the Fujitsu PBX that I built with mgetty/pppd and have the lines provisioned the same way as those dial-up server, ESF, B8ZS, and E&M wink start, so I have confidence in the guys who set up the PBX. I've built a loop back plug

We have an old Telrad 128KSU PBX to which I am trying to connect asterisk in the following manner: Current Setup: Telco-> T1->PBX Desired Setup: Telco-> T1-> Asterisk-> T1-> PBX. I am first trying to setup the Asterisk -> T1->PBX part without disturbing existing setup so I can get asterisk to forward calls to PBX and once that is done, I would try to move the telco

Hi all, using * 1.2.9.1 and this week all of the sudden calls keep ringing even after they've been picked up... Here's one users summary: When I pick up the phone, I hear a dial tone and I am able to dial out. But for some odd reason, the receiving line picks up while the outgoing line is still ringing. And the receiving line can hear everything while the phone is still ringing. I tested

Hello, I'm trying to make my asterisk box to act as a telco, in order to reproduce a US environment in europe. Our telco provider is giving us those settings: ESF B8ZF Inbound = E&M Immediate Outbound sig =Wink Start Yield to Glare = Yes Those trunks are using CAS for signaling. I have tried many configs/combinations in zaptel.conf and zapata-channels.conf In zaptel.conf, when having

Hi All, I have installed a Digium TE110P card on an Asterisk 1.2.1 system. Its connected directly to the PSTN. But I am unable to make outbound calls on the zap channels. The light on the card is green. Asterisk CLI shows all 24 channels when I give the command 'zap show channels'. I also noticed that Asterisk CLI shows an incoming call every few seconds on the 24th channel. This must be

I just had the same exact problem this morning. The only thing I've done in the last couple of days is update update zaptel. I rolled back my zaptel to 2/11/04 from 3/8/04. And kept my libpri from 3/8/04. I never had this error before updated. I had other issues, but not this one. -sb -----Original Message----- From: asterisk-users-admin@lists.digium.com

HI, I'm trying to config a span from port 2 of a DIgium T410p to a Brooktrout TR114-P8V-T1 card. I have a T1-PRI from the TELCO in port 1 (thru first port) working just fine with Asterisk 1.0.3 - been working fine for some time now. No problem with dialplan PSTN calls. Now I'd like to "route" specific DID numbers in thru the TELCO T1-PRI and out thru the second port (span) on

Hi, I have a client that has a 24 channel voice T1 that I have been using e&m signalling over for a number of years. The local telco finally got an ISDN switch and wants to move them to PRI. I didn't see this as a big problem - I've done a few others on this particular Caribbean island without issues, but this would be the first time with a Xorcom unit involved. We tried to do