similar to: Asterisk not waiting for E&M Wink (I think)

I am preparing to connect an asterisk box with a redfone fonebridge to a T1 service provider. I am doing this by testing first with another asterisk and a Sangoma card playing the role of telco. I formerly had this test configuration operating flawlessly as a PRI connection. But I discovered that I will need to use E&M, thus I've chosen the parameters as described in the subject

Hi, Did anyone manage to connect either Digium or Sangoma T1 card to any other PBX/gateway using T1 E&M Wink/Wink signaling? I'm trying to connect Avaya Definity to an Asterisk box with T100P and so far no luck. (I know I can do so with ISDN PRI, but need an additional ISDN processor card for Definity.) I tried to connect Definity to Cisco 3640 CCME (call manager express) to test the link

I could only get *ANI*DNIS* working one way and that was setting my signalling type on the Asterisk side to 'featd' The Definity won't send *ANI*DNIS* information back to the asterisk as far as I can tell. Other than that, I've been running it with wink/wink E&M for a while now. TN464 circuit pack on the definity side, te110p on the asterisk side. Just a crossover cable

Attempting to talk to an Eagle Telephonics switch at a disaster exercise. Didn't think a plain old E&M wink start T1 would be this much of an issue. We finally got the Eagle to accept a call from *, but whilst I can hear the person on the Eagle, they can't hear me. When they initiate a dial out I only get the first 2 digits from their switch... Does anyone have decent

We're having some difficulty connecting a T1 fax board card to asterisk, with E&M Wink. We've successfully connected it to other E&M Wink T1s, but have been unable to get asterisk to hear it's dialing. Asterisk can dial down to it with no problem, and it hears all the digits, but whenever it sends digits down to asterisk, * always only "gets" the first one. This is

Hi List, I have some T1 750s; hookup via a T1 to a TE420P card. We have them all set as E&M wink trunks. We get a dial tone and can call numbers, but when i call another number the ringing I hear on my phone is very weird, its not the standard ring tone. What will cause this? Is this a * setting or something in the Adtran I am fixing, I just want good ole ringing to be heard! Any help would

List: I already have asterisks up and running on a PRI, but where we are moving we cannot get a PRI so we are going to get T1. My question is: We are going to us E&M Wink for signaling with DTMF and caller id. The channels are going to be setup like this, 12 channels for 2-way and 12 channels for incoming only with DIDs. How would I configure the zaptel.conf? I realize that I will have two

I am setting up a box with a T100P. Everything is going well. The company I am working with has their one phone switch gear. They provisioned me a E&M Wink T1. Cannot do PRI unfortunately. We chose E&M so we could pass an unlimited number of DIDs to the trunk as apposed to FXS loopstart signaling. I can make outbound calls no problem, but I am having problems with the dial plan for inbound

Hey folks, I'm pulling my hair out on this situation and would welcome some advice: I'm using the AMI Manager to Originate calls onto 2 E&M wink T1 circuits via a T4XXP card from Digium. Everything works fine for about 600(+/- 50) calls then the Manager is suddenly unable to launch calls. Using ZapBarge to listen to the channels themselves you can hear the dtmf digits being dialed,

I'm trying to get a patch tested for inclusion in CVS. Anyone that is running E&M on a T1 and had to fool around with emdigitwait could you please try this. This patch removes the need for the emdigitwait parameter and speeds up dialing. This situation is mostly interfacing a legacy PBX/Key system with Asterisk. I've been running a couple of systems with this patch for

I'm getting red alarms with my T100P card that last from 4-15 seconds. They seem to happen randomly, every couple of days. Has anyone seen this behavior, or does anyone have any ideas regarding what would be causing it? Thanks, Glen

Hello, I've got very annoying behaviour from our asterisk PBX. We have 12 channels T1 e&m wink start for TDM and using iax softphones internally (iaxcomm, but tried firefly-thirdparty and discarded for bad sound quality). Slackware 9.1 w/ kernel 2.4.26+ digium TE110P card. In some cases when call is placed from softphone to TDM, system does not detect call answered on Zap channel and

I am an Asterisk newby, and I cannot seem to get Caller ID information from our T1 line. When calls appear at the phones, they say the call came from "asterisk" and unknown number. I know how Caller ID information is passed on an analog phone line (between the rings) but with a T1 line, I don't know technically how it is done. I don't see the caller's number in the

I am trying to make an in/out trunk group comprised of 4 DS0's using E&M Wink signalling. The first four channels of a DS1 on a T100P are being used for the group. Outbound calls work fine, but inbound calls fail. The other 20 DS0 channels are used for a PRI. Does the configuration shown below look okay? I've tried setting 'immediate => yes' without success, but it

Maybe one of you can help me with this: We have T1's that come from both MCI and Global Crossing as uses channelized (24 Ports per T) with inband (DTMF) ANI and DNIS delivery (format = *DNIS*ANI*). My old equipment was set for D4, AMI, SF and Wink Start and so is Asterisk Server. I've moved these T's to Asterisk TE410P and inbound calls are arriving to external voice mail

Does anyone know the default E&M Wink timings for Nortel DID ports? The default settings on Asterisk are: ; prewink: Pre-wink time (default 50ms) ; preflash: Pre-flash time (default 50ms) ; wink: Wink time (default 150ms) ; flash: Flash time (default 750ms) ; start: Start time (default 1500ms) ; rxwink: Receiver wink time (default 300ms) ;

I have a couple of live T1s sitting around and they are not ISDN(like most of the people that are using Asterisk seem to be using), they are regular old 24 channel, robbed-bit, E&M wink start, D4AMI T1 circuits. Can I get these T1s to work with a T100P Digium card and asterisk? Searching through the lists and the documentation I haven't seen any examples of how to configure this kind

I'm a bit confused about how to handle this. I have Asterisk sitting in the middle between a Qwest Long Distance T1 (Voice T1, D4, SF, AMI) and an external voice mail PC using a Dialogic D/240SC-T1 card. The Qwest T1 originally was connected to the Dialogic card directly. The signaling was set to E&M Wink Start because Dialogic used this as its default settings, so it just worked

I need to create a couple of tie lines between a legacy system and an Asterisk system. I was told that the tie lines are E4 Superframe E&M. I have done E&M wink but have no idea about E4 Superframe E&M and Google is not helping me here. Does anyone know about this type of signaling and if Asterisk can handle it? Thanks, Steve

Maybe of you guys know the answer to this: We have T1's that come from both MCI and Global Crossing as channelized (24 Ports per T) with inband (DTMF) delivery of ANI and DNIS (format = *DNIS*ANI*). My old equipment was set for D4, AMI, SF and Wink Start and so is Asterisk. I've moved these T's to Asterisk TE410P and inbound calls are arriving to external voice mail system