similar to: DELL PowerEdge 2850 and TE4110P and TE110P

-----Mensaje original----- De: Mario Montiel [mailto:mariomontiel@grupocsi.com.mx] Enviado el: Viernes, 26 de Mayo de 2006 10:29 p.m. Para: Asterisk Users Mailing List - Non-Commercial Discussion Asunto: RE: [Asterisk-Users] DELL PowerEdge 2850 and TE4110P and TE110P I have many problems with this server and two cards TE4110P, because after several minutes one of two cards stays out without

Has anyone had any compatibility issues with a TE110P card installed on a Dell Poweredge 1950? I noted the following error on the LCD display of the Dell Poweredge 1950: E1711 PCI PErr Slot 1 E171F PCIE Fatal Error B0 D4 F0. The Dell hardware owners manual states that it means the system BIOS has reported a PCI parity error on a component that resides in PCI configuration space at bus 0,

I'm a bit confused about how * constructs the RURI when it generates a BYE. For the situation where * send the initial INVITE it constructs the RURI for the BYE from the contact header of the 200 OK response which is well and good. However when * receives the initial INVITE it does not use the contact header contained within to construct the BYE's RURI but constructs it from scratch. This

Can anyone comment or share experences with using Dell 2850's with Asterisk. Proposed config is 2850, 2 x 3.6g procs, 2 g's of ram, 4 x 36g 15k rpm drives raid 10, Digium TE411P ( the echo cancelling cards ). Expected load is 1 or 2 pri's (most likely 1 ) 100 Polycom phones on the local network, 15 phone on a remote T1. 6 phone remote via the internet using IAX, Voicemail for

I currently have a single server with a few SIP and IAX upstreams for origination and termination with IAX clients. I am adding a second server that will have a much higher capacity and will be handling a larger call volume. However, this second server is not going to be geographically near the first. It will largely share the same upstreams. I would like for this to be an integrated system

I am so fed up with Digium cards. My company first owned a TE410P, I installed it in a Dell server and "enjoyed" its instability (we bought it months before Digium warned about the incompatibility issues). Then we switched to a TE411P for the hardware echo cancellation. Now we want to receive fax (< 20/day) on it and guess what ? Since April 2006 (again a few months after we bought

Does anyone know if you can have multiple TE110P cards in one chassis? -Thermal -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20061011/adbceeb5/attachment.htm

Exchange 12 will support "OVA" Outlook Voice Access. It will do this using VOIP. I was wondering if anyone has given any thought as to how Asterisk might interface with Exchange 12. It will do this using a VOIP gateway. If this could happen it seems to me this could be a really big win for Asterisk. I am going to setup a test server as soon as I can and start digging into this.

Hello Folks, I'm trying to decide here between a few cards for connecting an Asterisk box to a single E1 channel (either PRI or R2 signaling): - Digium E100P: has been replaced by the TE110P below, but can still be had at places like digitnetworks.com for $475, and I guess there's always a place for good-olde-obsolete cards in the world as long as they work :-) - Digium TE110P:

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Anyone have a 1650 running successfully in production mode with 2-4 PRI's? I want to make sure I don't have a motherboard compatibility problem before I buy one of these. We are going to be using a Digium TE210P to start off with and probably moving to the TE411P down the road aways? thanks, Sean -----BEGIN PGP SIGNATURE----- Version:

It will be interesting to see how many standards get broken, and how many proprietary hooks get thrown into the pot. The bean counters smell some money, and their OS franchise is waning: http://www.nytimes.com/2006/06/26/technology/26soft.html -- This message has been scanned for viruses and dangerous content by MailScanner, and is believed to be clean.

Does anyone have any ideas why my recently updated * 1.2.5 system should spawn multiple * process at seemingly random intervals? Regards L:ee ########################################### This message has been scanned by F-Secure Anti-Virus for Microsoft Exchange. For more information, connect to http://www.f-secure.com/ -------------- next part -------------- An HTML attachment was scrubbed...

Hello, Digium uses the Dell PE 2850 for their testing. This site says that 3.3V PCI slot. http://www.voip-info.org/wiki/view/Asterisk+hardware We are planning on purchasing a Dell PE 2850 and putting a TE205P card on it. However, the needs a 5V PCI slot. Does Dell PE 2850 has a 5V PCI slot? A person in our group tried to call Dell's customer support but they do not seem to know.

Hello Everyone, I checked with zttool that sometimes after the machine boots the order of the boards is changed like this: ??? Alarms Span ??? OK Digium Wildcard TE110P T1/E1 Card 0 ??? OK Digium Wildcard TE110P

Hi! I'm trying to setup a Wildcard TE110P with a PRI in The Netherlands. I get a Red Alarm on the line. Is there any way of debugging this? I've tried some configs that should work but without success. Is there any way of telling if the cabling is correct or what else the problem could be? Thanks!! Remco

Thanks! So aside from the lack of redundancy, will it perform well and scale to utilize a full T1's worth of calls through to the legacy PBX? We would probably build a backup server from old equipment and rsync the configuration files. Thanks again! > -----Original Message----- > From: William Boehlke [mailto:william.boehlke@signate.com] > Sent: Friday, May 20, 2005 3:33 PM >

List, I just tried to swap out our 410 for a 411 and we started have problems with on of our T1's. Setup: Span 1 - Dedicated PRI for long distance. Span 2 - 12 channels fxs_gs outgoing local. 12 Channels em_w incoming DID's. I didn't have any problems with the PRI. The trouble was with the T1. We were unable to place any local calls, and all incoming DID's where garbled.

I am trying to get the temperature of a Poweredge 2850 with CentOS 6.3 on it. Has anybody on this list done this successfully? Thanks -Surya PS: Apologies for cross posting if you are on the Poweredge list. -- Surya Saha Department of Plant Pathology and Plant-Microbe Biology Cornell University, NY, USA http://www.linkedin.com/in/suryasaha

I have an Asterisk server that was running fine until Sunday. Monday there was a power outage and the server was off most of the day. This server has a TE110P, two TDM04B and an Astribank 32. Today I noticed that the TE110P started having IRQ missess. Before today it only had about two or three per month. Today, this is the miss count after ten minutes on: IRQ Misses: 1443

please can someone send to me his files like zaptel & zapta if he si using TE110P thank you