similar to: EICON, chan_capi-cm and averlap receiving

Hi (Armin)! Does someone knows how to identify the type of the card? The delivery note says it is a V-4BRI-8M, whereas lspci reports a 4BRI-8M. What is it really? Are there any Eicon tools to identify the card type? thanks klaus 0000:0a:03.0 Network controller: Eicon Networks Corporation Diva Server 4BRI-8M Rev 2 (rev 01) Subsystem: Eicon Networks Corporation Diva Server 4BRI-8M Rev

Hi! I've bought the EICON DIVA V-2BRI card an begin installation soon. Are there any issues with certain kernels? E.g. the standard debian kernel 2.4.27-2-386 and kernel-image-2.6.8-3-686. Further current kernel 2.6.16.14 would be an option. Thanks Klaus

Hi (Armin?) ! Today I had a problem with Diva Server 4BRI-8M 2.0. Asterisk 1.2.12.1 chan_capi-cm-0.6.5 divas4linux-melware-3.0.f-106.622-1 Asterisk could not receive and make calls on the BRI ports, although the ports looked fine within Asterisk. I usually use "/usr/lib/divas/divactrl dchannel -c 1" to test line activity. This time there was no activity (cryptic log

Hi! I have some (short) question about the Eicon DIVA (V-)4BRI cards I want to have (short) answered before buying the DIVA card. I know there are several Eicon guys active on the list, thus I ask on the list instead of directly to Eicon so that all other will benefit as well. 1. Do Eicon DIVA (V-)4BRI cards support TE and NT mode? 2. Can the clock (master/slave) be configured independent

Hi Armin! I want to backup my Eicon Diva configuration (I'm using melware v3 drivers), but I could not find them. Where does Config Wizard stores the configuration? thanks klaus

Hi! This weekend we had a problem with our Asterisk Box which ran flawlessly for nearly 4 weeks. The Asterisk server sits between the PSTN and a Siemens PBX and bridges 2 BRI lines. No calls, not incoming, not outgoing. The admin rebooted the Dell Box and then everything worked fine again. Now, I'm analyzing log files to find the cause. During the Asterisk outage the logfiles only show

I am trying to use chan_capi with an Eicon Diva Server BRI. I installed the Eicon drivers from source including CAPU and I can use the board correcly using tty_test and minicom over /dev/ttyds01 or /dev/ttyds01. I need to insmod capi ( why? it is not written anywhere) and then capiinfo shows me all board parameters, but I have to break it otherwise capiinfo doesn't exit at all, but I don't

Hi list, Does chan_capi work with kernel 2.6? The Eicon Diva server card loads fine judging from /var/log/messages but Asterisk gives an error when trying to load the chan_capi module. I'm using chan_capi-0.3.5, zaptel-1.0.0, libpri-1.0.0 and asterisk-1.0.0 on a Fedora box with kernel 2.6.8-1.584. Zaptel and ilbpri work fine as does *. I have seen a msg that may be related and don't know

Hello, I have an issue getting the chan_capi module to load in asterisk cvs from today. Plain 2.4.20 kernel with melware patches for the Eicon Diva Server Bri card. I load the modules with: modprobe -v divas divacapi I load the firmware with: divactrl load -c 1 -f ETSI -vd6 Output in /var/log/messages is: Nov 9 19:26:26 voice kernel: Eicon DIVA - DIDD table (http://www.melware.net) Nov 9

Hi *, I want to integrate the Eicon Diva 4Bri Card to Asterisk. Eicon drivers and capi is installed. I use the latest dev version from eicon compiled and installed for my fedora 2 system. I found the chan_capi for asterisk from www.junghanns.net. Also loaded the patch and applied to the chan_capi source tree. I changed the Makefile to include the capi20.h from eicon:

Hi all, i have asterisk 1.0.9 with an Eicon Diva 4bri and chan_capi-cm-0.6. I have 2 NTBAs (one with did and one without). When using the one without did, i am able to place outgoing and incoming calls. When i use the NTBAs with did i have a layer 2 error. Anyone an idea? -- Executing Dial("SIP/2004-9634", "CAPI/g1/43XXXXXX") in new stack > data = g1/43XXXXXX

Hello all, I'm having problems getting chan_capi 0.3.5 to work well with an Eicon Diva Server card using using the driver from linux kernel both 2.6.10 and 2.6.12 (vanilla versions). I have a (really two) producci?n system(s) running chan_capi in another identical Eicon Card using kernel 2.4.27 and the Diva Server drivers from Eicon. I installed an compiled the source level rpm

Hi! I have problems with the ToN configurations in chan_capi-cm. I understand how incoming calls are rewritten using national and international prefix. But for outgoing calls - what is the ToN? Further, is there any debug info of the Ton? "capi debug" and the divactrl dchannel both show the CLI and CDLI, but do not show the ToN. How can I set the ToN? I suspect chan_capi to use the

Hi Armin! I have problems on debian sarge with standard 2.6.8-2-386 kernel. I've installed the packages: kernel-headers-2.6.8-2 kernel-headers-2.6.8-2-386 kernel-image-2.6.8-2-386 kernel-kbuild-2.6-3 kernel-source-2.6.8 Then I unpacked the kernel sources into /usr/src/kernel-source-2.6.8 and made a symlink from /usr/src/linux --> kernel-source-2.6.8 Then I entered

Hello, please look here: ================================================================= > > sprintf("%03s", as.character(1:5)) [1] " 1" " 2" " 3" " 4" " 5" > ================================================================= There should be a leading "0" isntead of space-chars?! I use R version

Hi! What are the typical ways to work around the 64 groups limit? thanks klaus

Hi all, I would like to announce the first release of the chan_capi channel driver on sourceforge.net The package is available for download with name chan_capi-cm-0.5 and is the current CVS HEAD. It is derived from the chan_capi-0.4.0PRE1 of kapejod. The main changes are: - complete rework - fix race-conditions - fix call state handling - rework of debug/verbose messages - added capiFax

Hello, I am using a system with an AVM ISDN PCI card (fcpci) and asterisk with chan_capi-cm-0.6. The hardware is connected to a Siemens Hipath 3550 PBX. As a BRI connection has 2 channels and allows 2 simultaneous calls, numbers/MSNs 6391 and 6392 were for provisioned for each channel. The system is working (partly, read on), the trick is the correct cable wiring and setup the PBX's port

Hi; I've got an AAH installation where a customer wants to install an active Eicon DIVA BRI card. AAH is built on Centos 3.5 which is currently at kernel 2.4.21.37. Support for Eicon active cards is built-in. I've debugged and run the A@H install-Eicondiva script but when I try to run divactrl load -c 1 -f ETSI -Debug I get a response : A: can't get card type for DIVA adapter

Hello all, I am trying to set up asterisk and hylafax to send and receibe fax. The machine is connected to the PSTN is an Eicon Diva BRI (1 BRI port). My problem is that , when I send a Fax from the PSTN to this machine, the asterisk or diva or hylafax, does not detect this call as a fax and asterisk answer that call like a voice call. How sould I configure the software modem (iaxmodem) to use