similar to: VoipBuster issues?

I am trying to move from IAX2 to SIP for voipbuster, moving at the same time to sip1.voipbuster.com. When I try calling out, I see that there is SIP exchange, and in many cases also RTP data being exchanged. Hover in a very large number of attempts the connection is not established. Half of the time there is no RTP, the rest of the time there *is* RTP data flowing in two ways, but no ringtone is

Does anybody else see the same behavior for VoipBuster connections? When I trace one of the other SIP peers, I see it sends this message: ---------------------------------------------------------------------- <--- SIP read from 82.101.62.99:5060 ---> SIP/2.0 180 Ringing Allow: INVITE,ACK,BYE,CANCEL,PRACK,SUBSCRIBE,NOTIFY,UPDATE Call-ID: 740540ee64fa957513ce89f03ef5e3f2 at sip.xs4all.nl

I have been pondering the following... Voipbuster used to announce the cost of the call, but the new SIP servers do NOT. Because there's the choice between free (VoipBuster) and non-free (ADSL), I'd like to let the user know which one is actually being used by announcing it before the actual call gets connected, ie immediately after the channel proceeds from setup to actual

/etc/conf.d/local.start -----Original Message----- From: Francesco Peeters (Asterisk) [mailto:francesco@fampeeters.com] Sent: Wednesday, January 11, 2006 3:21 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Cc: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] Zaptel modules load, but Asterisk fails at startup On Wed, January 11, 2006 21:36,

I forgot to pay this month's phone bill, and never noticed until family (the in-laws, who are too cheap to try the cell phone if landline fails, because it is 'more expensive') told me they were unable to reach us... As it turns out, the phone company disconnected us, but because Asterisk routes all outgoing calls in the Netherlands over VoipBuster, I never noticed anything! ;-) If

Hi, I am new here on this list, and have a problem of which I hope that somebody here can help me with it. I have a Voipbuster account, with which I would like to make phone calls via my Asterisk PBX. If I let X-Lite register directly at voipbuster.com, everything is OK, but if I let Asterisk register there, it says "registration for XXXXXX@sip.voipbuster.com timed out, trying again",

Hang on.... there's a non commercial G729 codec that will work with Asterisk? Can someone point me to where I can find it? Thanks, Doug. -----Original Message----- From: Francesco Peeters (Asterisk) [mailto:francesco@fampeeters.com] Sent: Sun 1/22/2006 8:27 AM To: Asterisk Users Mailing List - Non-Commercial Discussion Cc: Asterisk Users Mailing List - Non-Commercial Discussion

Hello, I'm trying to receive a fax to my inbound number from voipbuster. Asterisk receives the call and starts the rxfax application successful, but then nothing happens. The calling party is still hearing a ringing tone, or sometimes nothing. Voicecalls are working correct and without problems. For testing I've add a local number (300) to the dialplan. When I call this number

Hi;? When connecting via VoipBuster or VoipStunt, "I can hear them but they can't hear me"?. This happens with VoipBuster or Voipstunt. Registration is done correctly. I thought it could be something related to NAT, but I don't have this problem when using VoipUser or Asterisk2PSTN, for example. ? I tried with different codecs: gsm, alaw and ulaw but no change. ? So, now?I

I downloaded and installed the none commercial g729 codec very often now I only disable HT on my systems I think * doesn't like this One of the guys @ digium advised me to turn it of, since they haven't written * to be multi treading any way The codec I download is the http://kvin.lv/pub/Linux/Asterisk/codec_g729-gcc-pentium4.so It should work fine. Wouldn't know what it

Hi, I'm using voipbuster at work, and I've got 2 questions: 1) Is it possible to send faxes using voipbuster connex? 2) Is it possible to cut off or cover the voice that say the charge per minute?(I've payed the '5' euro, and from that moment I've got it!). Of course I understand that is to let me know how much I'm going to spend, but I do not like it, expecially when

Hi, all I am still battling to connect * and voipbuster. What protocol does it use? Ethereal capture shows UDP traffic, but no SIP or IAX traffic when using their client. VoipBuster client connects to connectionserver.voipbuster.com on port 11112 for authentication. Call itself is placed on different server. I have tried to connect using SIP and IAX and it seems that no authentication is

Hi all, I am probably missing something ultimately obvious, but I have a problem configuring freepbx... Using Edgy Eft with the cvs freePBX 2.2.1 and followed the Ubuntu installation guide on freepbx.org. System pxe-boots from a server with NFS root on same Using * 1.2 current (from source, not .deb's) Using mISDN-streams (from source, not .deb's) Using freePBX-2.2.1 (from source, not

Hi, all, I got my * to work with voipbuster service. And it works quite well when I am calling USA or Europe. However, for local calls, I am experiencing long delays (About 1s). As far as I know, voipbuster application does not have this problem. I am using IAX and gsm codec. Any ideas on how to combat this? Thanks, Rudolf

Have you got termination set correctly? I have a B410P working with 2 x NT and 2 x TE ports successfully. I had to turn the 100ohm termination on on the NT ports (even though I have them set as PTP in mISDN.conf). HTH -->> -----Original Message----- -->> From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users- -->> bounces at lists.digium.com] On

Hi, all Here is a something I found on the web: http://www.voipbuster.com And it works OK too. Now, I want to use it via asterisk, so I ccan use my normal phones instead of PC application. Did anyone try to connect astersisk and VoipBuster? Thanks, Rudolf

Yep I did the same. -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Francesco Peeters (Asterisk) Sent: Saturday, 21 January 2006 5:34 PM To: fbraeuer@gmail.com; Asterisk Users Mailing List - Non-Commercial Discussion Cc: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users]

Trying again... *Summary:* I need to have 2 machines with 4 BRI connections, 2 in NT mode, 2 in TE mode and 1 machines with 2 BRI connections, 1 in NT mode, 1 in TE mode; What card(s) should I put in to these servers? *The long story:* I have 3 locations I want to connect using (*) servers. 1 of those has a single BRI with a Siemens DECT PABX. 1 of those has two BRI's with 2 Siemens DECT

I've tried to find some details on the wiki, but was unable to get a satisfactory result, so I am asking here: I have a Linux (FC3) box with these specs: vendor_id : AuthenticAMD cpu family : 6 model : 3 model name : AMD Duron(tm) Processor stepping : 1 cpu MHz : 797.388 cache size : 64 KB MEM: currently 256, looking to upgrade to 512/768

Does anybody know whether somebody ever implemented (linux) drivers or a chan component for the Com-On-Air cards, or is the only way to make it work the use of a Windows box as Dect to SIP gateway for *? (Or does it work at all?) I can still get the cards, which would be great to retire the old DECT based PBX, but it would be of little use if it's not going to work, now is it? ;-) --