similar to: mISDN trouble with a HFC Cologne card, Asterisk Asterisk 1.2.4 on Linux 2.6.16.11 - incoming DTMF detection

Use Set(CALLERID(num)=9999999999) instead of using CALLERID(all). Remember to set this BEFORE you Dial. -->> -----Original Message----- -->> From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users- -->> bounces at lists.digium.com] On Behalf Of Vieri -->> Sent: 06 February 2009 12:36 -->> To: asterisk-users at lists.digium.com -->>

You're quite right. We'll need to see your misdn.conf file to check the settings. -->> -----Original Message----- -->> From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users- -->> bounces at lists.digium.com] On Behalf Of Vieri -->> Sent: 06 February 2009 13:49 -->> To: asterisk-users at lists.digium.com -->> Subject:

Hi. I'm running Asterisk server with 10 sip phones, and 2 grouped T0 lines with 10 DDI numbers. My provider is France Telecom and my setup is : - Debian Lenny - Asterisk 1.4 - Linux kernel 2.6.25.17 - mISDN 1.1.8 driver - Sip phones Thomson ST2030 No problem with the SIP . But when reveiving a call on RNIS line (any of the DDI numbers), the associated SIP phone rings indicating _two_

hi i've configured a Beronet BN8S0 Card with misdn beronet utility. the card is configured with all lines in TE and P2P mode, and it is connected with the special cable with an ISDN connection. i've turned on debugging to level 4, this is the output from the asterisk cli when i receive a call: P[ 5] MGMT: Short status dinfo 1000001 P[ 5] MGMT: SSTATUS: L1_ACTIVATED P[ 5] handle_frm:

I'm trying to set caller ids on outgoing calls. I have a quad BRI B410P card connected to my telephony provider. I know the list of DID numbers the provider assigned to my company. If I don't set the caller id then the callee always sees the same "top-level" number. If I set the caller id to a specific DID number we own, the callee keeps seeing the "top-level" number,

i am using asterisk 1.6.2 with mISDN and a passive AVM Fritz!card on CentOS 5.5. The only thing, i want to do is a call-redirection from an isdn-call to my mobile via sip-account. My extension conf is: general] static=yes writeprotect=no [globals] OUT_PORT=1 [ISDN] exten => 12345,1,Dial(SIP/012346737222 at sipprovider.local) If i call to the msn 12345, the SIP-call is going out, but after

Just to add.... P[ 1] Transmitting 128 samples 2 misdn P[ 1] writing 128 bytes 2 asterisk P[ 1] Sending :160 bytes 2 MISDN P[ 0] misdn_jb_fill: written:160 | Buffer status:256 p:861fee0 P[ 0] misdn_jb_empty: read:128 | Buffer status:128 p:861fee0 P[ 1] Transmitting 128 samples 2 misdn P[ 1] writing 128 bytes 2 asterisk P[ 1] PH_CONTROL: channel:1 oad2:07nnnnnnnnn dad0:820055 P[ 1] --> DTMF

I'm running a setup with chan_misdn on a austrian PTP-line. When somebody dials in without an extension, he gets a busy signal. I don't see the call at all in asterisk. I *have* set immediate=yes in misdn.conf. And I *do* have an s-extension in my dialplan for the context used by misdn. Calls that provide an extension work fine. Attached is my misdn.conf and a verbose 3, misdn set debug

I am trying to use misdn insted of zaphfc to drive two billion isdn cards zaphfc is ok, but the problem with cdr and the fact tha you always have to wait the bristuffed version of asterisk took me to try another way. so I downloaded the misdn installation script from beronet for the last version ( I am using asterisk stable 1.2, so now is 1.2.5) wget

Hi, Hi All, I've just delved into the world of asterisk and I'm having a few dtmf issues. Internally, amongst sip phones, dtmf is fine. Externally, if you ring from a GSM mobile, DTMF is fine, however if you ring from a standard phone, DTMF fails to register. I am attempting to use a quad port HFC-4S Beronet Card. I've been searching the web most of the last week and

I hadn't used FWD for quite a while. A customer sent me an email last week, "Is FWD broken when one tries to use it with IAX?" I have been playing around, and indeed seems to be the case. Is there anyone out there successfully using the two of them together? Thanks. B. -- This message has been scanned for viruses and dangerous content by MailScanner, and is believed to be

Which the way easiest to compile the kernel 2.6.16.11 in Centos 4.3 generating a package rpm? -- [ ]s, Analista de Rede Leandro Costa :wq ...... __@ ...._ \ >_ ...(_)/ (_)_________

Hi everybody I have installed a TrixBox with Asterisk 1.2.14 and relative upgreaded software. I Bristuffed it with last version of bristuff to use a Hemlet PCI ISDN CARD in a normal Italian EUROISDN installation. The * works fine except for the ISDN CARD. It is always Channel D down, but if a Call comes in, it works perfectly for some time, both inbound and outbound. It prompts Channel D UP!

Hi to all, I am searching to make work an Asterisk, with an ISDN card with Cologne Chipset. Here is the lspci: 01:09.0 Network controller: Cologne Chip Designs GmbH ISDN network controller [HFC-PCI] (rev 02) Subsystem: Cologne Chip Designs GmbH ISDN Board Flags: bus master, medium devsel, latency 16, IRQ 5 I/O ports at c400 [size=8] Memory at fdefd000 (32-bit,

It seems there are a number of Centos users in the Cologne/Bonn/Aachen area of Germany. If there is not one already (and please let me know if there is!) I'd like to start a Linux User Group (including Centos) for this area. I'm way down in Blankenheim, though. Would someone like to volunteer a location? I envision alternating meetings between the three cities if possible... just

Hi, Since a week ago I am trying to get chan_misdn working with asterisk 1.4.19, using HFC based ISDN card on Linux 2.6.22. My setup is done as detailed on wiki and FAQ. * mISDN and miSDNusers are 1.1.7.2, unpacked, build and installed. After installation and misdn-init, I have this: aragorn:root/pts/1: # misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) ->

Hello, After upgrading my kernel to mISDN-1.1.1 while keeping asterisk-1.2.16 I no longer match any extension. Apparently the "dad" is empty. However I can see the number just before it (146472130): P[ 4] I IND :SETUP oad:!?145201798p ?146472130 dad: ?146472130 pid:2 state:none P[ 4] EXPORT_PID: pid:2 Mar 23 09:35:28 WARNING[6725]: chan_misdn.c:4750 chan_misdn_log: Extension can

Hello list, I've been having a problem for some time now that I can't figure out how to solve it. On a PTP BRI ISDN line, if I have both channels in use and I place a third call from the outside, I'm not getting a busy tone like I should. Instead I get a congestion tone, as if the line was not working/didn't exist. Currently I'm using mISDN 1_1_9.1 and Asterisk 1.4.35 with

I'm experiencing some odd issues with Virtualbox running on 9-STABLE. where my network periodically disappears ? sometimes, it comes back again after a few minutes, other times I have to reboot the server ? This last time, the error on the screen states: bce1: bce_pulse(): Warning: boot code thinks driver is absent! (bc_state = 0x00004006) I had 20 regular 'jail' VPSs running on it

Recently under amd64 and 9.1-STABLE I am seeing issues with the bce driver. Message is "Warning: bootcode thinks driver is absent". After this message, the box appears to be wedged. After rebooting, it got the same message during fsck. So we installed 9.2 pre-release using a snapshot iso from 7/13/13. Shortly after boot we got the same message. We are now in the process of