similar to: H323 calls will not stay connected

Everyone, I have been trying to connect a PBX with H323 IP trunks with g711 codec to my Asterisk server running ooh323 service. I can place calls to and from either the Asterisk, or PBX with no problem, but when I try to pickup the call on either end, the phone hangs up immediately. Debug shows normal to me but at the last few lines of data there is an error shown that I have not been able to

has anyone managed to get these three beasties to work together ? we're using ooh323 from asterisk-addons-1.2.2, asterisk 1.2.6 and microsoft netmeeting default from windows xp. the symptoms are that calls from a SIP client to NetMeeting rings on NetMeeting, but upon answering the call in NetMeeting, no audio is passed between the two. eventually, the call times out and hangs up. on a

hi .. i've just installed and licensed an instance of the G729 codec. I am trying to connect through asterisk to Go2Call server .. According to their info it involves dialling extension 729 on voip01.go2call.com, to get the IVR. my extensions.conf shows : exten => s,2,Dial(OH323/h323:729@216.52.153.206) which I think is correct, I have G729 enabled in the OH323.conf file and it seems to

Hello, I've been trying to send traffic to a Cisco Call Manager 3.2, but with no luck. Here's whats happening: * Call gets to CCM * Call gets to the gateway * Rings a couple times on destiny * Call gets hungup. On the CCM I get the following error: MediaManager - ERROR wait_AuConnectErrorInd On the Gw (Cisco AS5300) I get a disconnect cause of 2F (Resource not available) On asterisk:

FC2 Asterisk 1.0 When I dial a H323 dialup to an existing OKI Voip Router (BV1250), I get an EndedByRefusal yet the OKI Gateway is setup with the corrent reply ip addresses etc etc, unfortunately its an existing multiple voip router setup with g723.1 and g729a, so changing the codec on the router maybe an issue. I have compile in the h323 as per the channels/h323 setup with the listed libraries.

Hello, I think I have the same problem as Martin Bene mentioned in http://lists.digium.com/pipermail/asterisk-users/2004-January/034521.html Since I found no further information about this I'd like to ask wether you know what the reason for this problem is and how one can get around this. * is registered to the innovaphone gatekeeper. Trunk connection is done with an AVM-B1 and chan_capi.

I have searched and searched for over a week on this but can't seem to find the issue. Calls from CallManager to Asterisk are being disconnected immediately. I have setup CallManager and Asterisk per Shaun Ewing's pdf http://asterisk.edropbox.net/ccmasteriskvm.pdf I have installed Asterisk 1.4.0-beta3 on Fedora Core 5. I got libpri, zaptel, and asterisk compiled and installed.

Hello, Users. I loaded module chan_h323.so, chan_vpb.so. I have met a message : "No one is available to answer at this time". I don?t know what I do.. My 'h.323 trace 5' result is : == vpb/1-8: Starting record mode (codec=0)[AST_FORMAT_SLINEAR:VPB_LINEAR] -- Executing Dial("vpb/1-8", "h323/192.168.1.107") in new stack 1:21:34.936 ThreadID=0x06f2bbb0

I'm attempting to get chan_h323 working on Asterisk CVS-STABLE. I've compiled it ok using the Janus release of pwlib/openh323, by editing the makefile as per the comments. Call setup and cleardown seems to work fine, but no audio is being passed in either direction. Doing an "h.323 trace 9", I noticed the following sequence at the end of the call setup: h323.cxx(1685)

>Please I have combed the Archive to no avail on this problem protocol >control problem in oh323. >I'm receiving calls from CISCO AS5300 -> Asterisk -> Zap Channel. The >calls clears the remote location but drops on my own end. Please what >could be >wrong. I have included the oh323.conf and log files. I have tried >various configuration and I thought I should

Greetings All- I have an * box with the NuFone H.323 channel driver installed. I also have an Altigen VoIP system with a PRI to the PSTN. I can sucessfully make a call from a SIP extension (snom190) to an H.323 extension (altigen phone) The thing I can't seem to make work is a call from a H.323 phone to a SIP extension. Here's the layout:

I have on Chan_h323 with G729 and X100P trying to connect to a Planet VOIP400 gateway box(http://www.planet.com.tw) I uncommented g729 in the Makefile and I'm setting g729 in h323.conf I'm receving in my side: 1:20.906 H225 Caller:810f070 h323ep.cxx(1537) H323 Clearing connection ip$localhost/4112 reason=EndedByRemoteUser and the other side(Planet) says: 15- RADH 2

i am trying to make calls between two workstations using netmeeting and asterisk. i get the popup on both when i call the extensions 665 and 667 but when accept, i get this error *CLI> 0:18.190 H225 Caller:8112978 H225 Received connect PDU. 0:18.288 H245:810b388 H245 Read error: Bad file descriptor 0:18.318 H323 Cleaner H323

Hi all, I am trying to use a "Siemens optiPoint 300" IPPhone (H.323 only) with Asterisk (1.0-RC2). So far I have been using the H.323 channel included in the tarball (Nufone ?). I encountered a strange behaviour when I try to make a call from the IPPhone to my Asterisk box : =====> here is the H.323 configuration for the incoming calls (192.168.1.50 is the IP of the

Hello all, When I generate an out-going call from *, the DTMF detection is not working ? ASTERISK --> GW AS5300 --> PSTN But the DTMF is working correctly when it's an incoming call. PSTN - -> GW AS5300 - -> ASTERISK Well, I tried with the 3 dtmfmode of asterisk inband, rfc2833 and info, no way !!! Is it normal that asterisk try to setup the outgoing-call using ULAW ? if I

Hello, Has anyone experienced a segmentation fault in asterisk for using G729 against an AS5300 in SIP ? I'm having this problem. Also, any other codec I use gives me incompatible media (can be read in SIP DEBUG messages). AS5300 configured for multiple codecs, so is Asterisk. Tried G711u/A G723 and G.729. Any clues ? Regards, Jorge A. Info: Asterisk ver 1.0.7 stable Using AMPortal

Hello all, I just installed Asterisk with H323 support (chan_h323 from Jeremy McNamara). But experience problem while connecting OpenPhone to Asterisk Here is h.323 trace: 5:37.444 H323 Listener:9c86de0 transports.cxx(1504) H323TCP Started connection: host=10.120.160.15:3172, if=10.120.160.99:1720, handle=27 5:37.444 H225 Answer:9cc1250 transports.cxx(564) H225

Folks, I have a NEC 2400 pbx(non-voip) behind a Cisco 3725, connected via standard wic-t1 card. The NEC needs to call two different asterisk servers with 4 digits. I have two way calling working with the one * box, but the other is perplexing me. Here's the layout * <--> Cisco 2811(192.168.13.1) <--> 1.54 point to point <- Cisco 3725(192.168.8.1)<-> NEC 2400. The

Hi Gurus, We have configured asterisk to trunk with avaya with ooh323 channel driver. The sip phone registered on asterisk can dial the extensions registered on avaya via this trunk , and vice versa works too. Even we can make the avaya branch to dial asterisk?s extension and then this extension dial back to another avaya?s extension. But if we dial the external DID number via this trunk from

For the benefit of everyone, having H323 Configuration problem due to H245 Tunnel, check the h323 Config embeded at the end. Comment the offending line as under: ; ; Enable H.245 tunnelling (yes,no). ; h245Tunnelling=yes ; -----Original Message----- From: Tola Ogunsan [mailto:tolaniye@hotmail.com] Sent: Wednesday, May 25, 2005 1:03 PM To: Kanuri, Seshu (Company IT) Subject: RE: oh323 problems