similar to: Need help configuring TE100P and 3 X100P clonewith MD3200 chipset

This is a system for our lab. I have no problem getting rid of X100P clones. But I am just curious why can they work. Even the drivers are not loading correctly. -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Kerry Garrison Sent: Tuesday, May 02, 2006 10:51 AM To: 'Asterisk Users Mailing List -

I can either get the TE100P working or the 3 X100P clones working, but never both. I have the TE100P connected to a channel bank, and X100P clones to lines from the phone company. This is my zaptel.conf span=1,1,0,d4,ami fxsks=1-24 loadzone=us fxols=25-27 loadzone=us I then do [root@asterix root]# modprobe zaptel [root@asterix root]# modprobe wcte11xp ZT_CHANCONFIG failed on channel

I have a X100P and a TE110P in my Asterisk box. I can either get the X100P or the TE110P to work, but never both. Here's my zaptel.conf span=1,0,0,d4,ami e&m=1-24 fxsls=25 When I load wcte11xp and wcfxo, I will get this error. [root at asterix etc]# modprobe wcte11xp ZT_CHANCONFIG failed on channel 25: No such device or address (6) /lib/modules/2.4.20-8/misc/wcte11xp.o: post-install

Hi, I'm cutting my teeth setting up a home asterisk server, but having some trouble getting Zaptel to recognize a X100P clone PCI (Motorola SM56 which should work according to various wiki's). What struck me was that the "/proc/interrupts" do not include IRQ 11 as the "lpcpi -v" is reporting. Am I missing something fundamental here? Any hint is greatly

Hi there my zaptel hardware is giving errors while loading but they seem to load just fine. the lights wil work and my wctdm card is also workin and the isdn works to But when I stop asterisk I have to reload al cards again is this normal? This is my zaptel.conf is there no way to group these because my te110p is giving an error that it can't find channel 35 but 35 belongs to my wctdm.

Hi, This error I got it just when I gonfigure zaptel support isdneuro 31 channels. But if I configure zaptel to support T1 and just 24 channels I have no problem. ######################################################################## #### # # Zaptel Configuration File # # This file is parsed by the Zaptel Configurator, ztcfg # # loadzone = it span=1,1,0,ccs,hdb3,crc4 bchan=1-23 dchan=16

It seems the information out there on this topic was confusing enough to cause me to waste a lot of time, and that this topic is rehashed periodically. So now it's my turn.... I had a modem with an Intel 537EP chip on it and thought it might work with the zaptel drivers. Initially, it seemed the only issue would be the PCI device & vendor codes. Then, I ran into the problem that

Hello all. I have here a TE110P (configured as E1) and a TDM400P (with four X100P - FXS). Both boards are recognized by the operating system as showed above: 0000:08:00.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface Subsystem: Unknown device b1d9:0003 Flags: bus master, medium devsel, latency 64, IRQ 169 I/O ports at e800 [size=256]

I go to my Zaptel 1.4.0 folder and run ./configure; make linux26; make install and I don't see any errors. This is out of my modprobe.conf: install tor2 /sbin/modprobe --ignore-install tor2 && /sbin/ztcfg install torisa /sbin/modprobe --ignore-install torisa && /sbin/ztcfg install wcusb /sbin/modprobe --ignore-install wcusb && /sbin/ztcfg install wcfxo

Hello, i've googled and can't find a definite answer, so here goes: I have purchased the Digium TE100P, and am setting up the connection, however the telco i'm supposed to work with does not support PRI/ISDN E1 connections. They only support E1/R2 lines. Is there a way i can make the TE100P work with this? I've not seen any zaptel.conf that supports this. Any workarounds?

Ok so I read the Linux 2.6 related README and finally compiled propperly, I thought but at the end I notice that lscpi does report the cards, but I cant modprobe wcfxo nor zaptel and I do have wcfxo.ko in the /lib/modules/2.6.8/extra/ directory, so what gives? This is a Debian Sarge, thanks! # # make clean starts here # make[1]: Entering directory `/usr/src/zaptel-1.4.0/menuselect' rm

I got a new motherboard and upgraded Asterisk, ... However, I am not lucky enough to get it running again. To compile went ok, besides this remark at the end of asterisk: WARNING WARNING WARNING Your Asterisk modules directory, located at /usr/lib/asterisk/modules contains modules that were not installed by this version of Asterisk. Please ensure that these modules are compatible with

asterisk*CLI> dahdi show status Description Alarms IRQ bpviol CRC4 T2XXP (PCI) Card 0 Span 1 OK 0 0 0 T2XXP (PCI) Card 0 Span 2 RED 0 0 0 On Thu, Apr 2, 2009 at 9:40 PM, Martin <asterisklist at callthem.info> wrote: > That's very strange ... the code when is

Hi, I'm wondering why zttest shows Best: 99.976 -- Worst: 99.967 -- Average: 99.971469, Difference: 99.971469 Shouldn't it be 100% as timing is hardware and comes from PRI? Am I missing some kernel config? Regards, Atis My /etc/zaptel.conf is span=1,4,0,esf,b8zs span=2,3,0,esf,b8zs span=3,2,0,esf,b8zs span=4,1,0,esf,b8zs #lspci 07:03.0 Communication controller: Digium, Inc. Wildcard

Hi List, I am having some trouble with installing the latest version of ztdummy on a CentOS Kernel 2.6 system. I have installed a few Asterisk systems on Slackware Kernel 2.4.x without any issues, unfortunately there is no choice about this distro, or kernel as it has been preinstalled by someone else. And so I am in the dark with an unfamiliar distro and kernel. I am fairly sure the

Hi, I have a Gateway running in "TE" (terminal equipment mode as "slave" that I need to connect to my asterisk server using a TE100P card. Can anybody give a quick run up of how to run the TE100P's in Network Termination mode to have this working sucessfully? Cheers! Regards, Sahil Gupta VoiceValley

hi you, I'm having problem with voice quality on my trixbox using TDM2400B.The trixbox is connected via 20 FXO ports on a TDM2400 with the hardware echo cancel module. Echo cancel almost works, but the users hear what they describe as a 'background crackle/buzz' coming back when they talk. anyone have the same problem? pls help me. thanks a lot. my trixbox and config

/bin/sh: -c: line 0: syntax error near unexpected token `;' /bin/sh: -c: line 0: `if [ -n "" ]; then if [ -f ]; then mv -f .bak ; fi; cat .bak | grep -v "alias char-major-250" | grep -v "post-install torisa /sbin/ztcfg" | grep -v "post-install wcfxsusb /sbin/ztcfg" | grep -v "alias wctdm" | grep -v "post-install wctdm

Hi, I have a problem I will describe. I have PAP2 connected to the internet to an asterisk box with 2 TDM cards, one TE100P E1 with PRI and one TDM400P with 2 FXS an one FXO. When I call to the TDM400 cards from the PAP2 eveything is OK, sound quality is perfect. When I call to terminate the call in PSTN through E100P I hear clicks which aparently are RTP packet looses. This clicks are only heard

Hello everyone, I have a Atcom AX-1600P(1) card with a FXO module and I can't configure it. I have four extension with this PJSIP settings: --- /etc/asterisk/pjsip.conf --- [transport-udp] type=transport protocol=udp bind=0.0.0.0 [6001] type=endpoint transport=transport-udp context=from-internal disallow=all allow=ulaw auth=6001 aors=6001 direct_media=no rtp_symmetric=yes force_rport=yes