similar to: Problems with zaptel and TE210P

Hi, I have debian etch 4.0 machine (2.6.18) with two TW-ISDN PCI (Hfc) cards. I use bristuff-0.3.0-PRE-1y-e (asterisk-1.2.17,libpri-1.2.4,zaptel-1.2.16). I also have patched zaphfc with zaphfc_0.4.0-test1_florz-13.diff.gz (I load module: insmod /usr/src/bristuff-0.3.0-PRE-1y-e/zaphfc/zaphfc.ko modes=1 debug=1). So i want to test two cards and make loop between them. So one card would be NT,

Hello everyone, We have recently turned up a new T1 from McLeod (Midwestern CLEC). It is configured like so: /etc/zaptel.conf: loadzone=us defaultzone=us span=1,0,0,esf,b8zs ;(also tried 1,1,0,esf,b8zs) bchan=13-23 nethdlc=1-12 dchan=24 /etc/zapata.conf: switchtype=national context=pri-in signalling=pri_cpe group=1 channel => 13-23 I can get hdlc0 (and pvc0) up just fine after the

Hello. I have a TE212 configured in E1 mode. This is shown in a cat /proc/zaptel/2 and 3 (where the card is configured): cat /proc/zaptel/2 Span 2: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" HDB3/CCS/CRC4 RED NOTOPEN 25 TE2/0/1/1 Clear 26 TE2/0/1/2 Clear 27 TE2/0/1/3 Clear 28 TE2/0/1/4 Clear 29 TE2/0/1/5 Clear 30 TE2/0/1/6 Clear

Hi list! I'm trying to setup Digium TE205P E1 card to work with my provider (and Ericsson BP 250 - this comes later). When I execute "pri show span 1" this is what I get. pbxzg1*CLI> zap show status Description Alarms IRQ bpviol CRC4 T2XXP (PCI) Card 0 Span 1 OK 0 0 0 T2XXP (PCI) Card 0 Span 2 UNCONFIGUR 0 0 0 pbxzg1*CLI> pri show span 1 Primary D-channel: 16 Status:

Is anybody else using the following combination: * a TE410P card (wct4xxp driver) * a BT ISDN connection * DAHDI 2.3.0.1 * Asterisk 1.6.2.9 I'm trying to configure a new box to replace a legacy system (same hardware; some old version of Asterisk with Zaptel; works lovely but hopelessly out-of-date) and not having much joy. Specifically, I couldn't get it to see a D-channel on

hello, i installed an asterisk as a pri gateway. Everything is okay. /etc/init.d/zaptel starts successfull with wct4xxp module. /etc/init.d/asterisk starts also successfully. I tested my pri cable and it works. But still my span isn't up. I don't see any error. Do you have any idea? What else i should check? Thanks. My card is 4 span Wildcard TE410P

Hi Guys, Anyone might know why this error keeps showing up and inbound/outbound is not working on a Bell PRI with Sangoma A101D? -- Got SABME from network peer. Sending Unnumbered Acknowledgement No calls can be made inbound/outbound. Keeps repeating. No alarms ON and no changes been made to the system. Stopped all a sudden. Asterisk CLI doesn't show anything with full verbose for both

Hi all, My problem boils down to these errors: ... Unable to create channel of type 'ZAP' (cause 34 - Circuit/channel congestion) == Everyone is busy/congested at this time This is triggered by lines in extentions.conf such as: exten => _X.,1,Dial(ZAP/g1/${EXTEN},,W) The system is CentOS v5.2 with Asterisk 1.4.23 (druid-asterisk-1.4.23.1-2), a Sangoma A104

We have a server with a TE120 on a partial PRI trunk that several times a day declares the PRI trunk down and stops handling calls until the asterisk is stopped, the zaptel/te120 modules reloaded, and asterisk started. Just before things go down, the log shows the following error: ERROR[9424] chan_zap.c: Write to 28 failed: Unknown error 500 at which point a "show pri spans"

Hello, I have following problem with Sangoma A104 card: CLI> pri show span 1 Primary D-channel: 16 Status: Provisioned, Down, Active Switchtype: EuroISDN Type: CPE Window Length: 0/7 Sentrej: 0 SolicitFbit: 0 Retrans: 0 Busy: 0 Overlap Dial: 0 T200 Timer: 1000 T203 Timer: 10000 T305 Timer: 30000 T308 Timer: 4000 T313 Timer: 4000 N200 Counter: 3 NOTICE[16509]: chan_zap.c:7494 pri_dchannel: PRI

Hello all. I have an NEC PBX connected via a TE210p E1 line to an asterisk 1.6 box. NEC -> E1 -> TE210P:1 -> * -> TE210P:2 -> E1 -> Telco Incomming calls from the telco to the asterisk box to the NEC work fine with indials and everything. Works sweet. Outbound from the NEC to the Asterisk box fail. Giving an long dial tone that then times out. Ie, pick up NEC handset, dial

I have a server running Asterisk 1.4.14, Zaptel 1.4.6, Libpri-1.4.2 on a CentOS 5 server. The server has a single TE110 card connected to a provider called Alestra in Monterrey, Mexico. Since we installed everything we have been having problems dialing certain numbers, those numbers always fail when dialed from Asterisk but if you dial from your cell phone they always go through. I once has a

I've got an asterisk 1.4.24 box with dahdi complete 2.1.0.3+2.1.0.2 I've got a 2 port T2XXP card attached with on T1 currently plugged in. Inbound calls work fine, but outbound fail with the rather cryptic: [May 19 17:28:07] WARNING[11360]: app_dial.c:1237 dial_exec_full: Unable to create channel of type 'DAHDI' (cause 0 - Unknown) There are similar threads I've found on the

Hello, I wrote earlier today about a new PRI installation in the Caribbean, where all outbound calls are functioning fine *except* calls to Sprint phone numbers, which get rejected immediately as "busy". The telco has been working with their switch manufacturer and took the output of "pri show span 1" from me and came back with this: ----quote--- Please check your timers

Hello, When trying to start VM I am getting the following error: # --- [root@xcp-dev01 ~]# xe vm-start uuid=f535e5bd-6540-3745-d494-14f776da85e5 Error code: INVALID_SOURCE Error parameters: Unable to access a required file in the specified repository: file:///tmp/cdrom-repo--2OF-Z/install.amd/xen/vmlinuz., , # --- I have used last xen server documentation to prepare the VM installation from

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 I am stuck in a situation where I have two te110p's and really need a te210P. Anyone interested in a trade? They are in working condition guaranteed. If this is the wrong forum for this, I am sorry... I will take it off list. -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.4.2 (MingW32) Comment: Using GnuPG with Thunderbird -

Hi list! I'm trying to setup a new * server with a TE210P in a Dell 2850 box. I'm using zaptel version 1.2.5, the linux flavour I'm using is CentOS 4. In a previous thread I read about the results I should expect from zttest. On my home box (using the crappy Asus A7V600) I got really bad results from zttest (just over 97.5) but I know that this motherboard just sucks. To my

Dear all I have now install TE210P 2 port E1 card on asterisk 1.4.10 on centOS 5 but thing is that i have connect 1 E1 port with avaya E1 back 2 back and second E1 card on Direct Telcom for outgoing for outside now i got this error when i call on avaya PRI asterisk think PRI_CPE and remote end also CPE i have configure /etc/zaptel.conf span=1,1,0,ccs,hdb3

I sent an email out to freebsd-net without a response, soo this is my last attempt at getting any assistance here. I have a QLE3142-CU-CK (rebranded NetXen NX3-20GCU w/ NX3031 chipset) with no driver support in *BSD from anything I saw. I came across solaris's ntxn driver which seems to work appropriately but I have no use for solaris as a host o/s. Naturally I'll attempt at trying to get

Hi all, I'm going to configure a middle asterisk installation. I'll use a TE210P to connect a T1 channel bank and a PRI E1 line. I'm thinking on using a SuperMicro P8SCT Mother Board that has a 1x 64-bit 133MHz PCI-X 3.3V. In TE210P documentation I've read: The TE210P is a 32-bit 33MHz card keyed for 3.3 volt operation. Can SuperMicro slot (that is a 133Mhz slot) be used