similar to: outbound calls to sip urls

On Sun, Mar 15, 2015 at 5:56 PM, Sonny Rajagopalan <sonny.rajagopalan at gmail.com> wrote: > George, > > I have the detailed log below. (Resending after trimming the email to 40KB.) > > The sequence below just repeats ad-nauseam. Is this a SIP trunk issue? > > Thanks! > I don't see anything obvious. The registration works though, right? You might want to compare

Hello: I have this situation: I can make calls internally, I can make inbound calls but I can't make outbound calls. Thanks in advance. These are my devices: * asterisk 11.8.1 = 192.168.1.22 * sipphone grandstream gxp2160 = 192.168.1.5 * gateway audiocodes mp-114 2fxs-2fxo = 192.168.1.4 port 1 (FXS) connected to an analog phone port 3 (FXO) connected to the PSTN These are my

Yes, I think the dial does get executed (sonny calling outbound 202-555-1212): core set verbose 3 Console verbose was OFF and is now 3. -- Executing [912025551212 at from-internal:1] Log("PJSIP/sonny-00000031", "NOTICE, Dialing out from "" <sonny> to 12025551212 through fromgw") in new stack [Mar 15 19:27:06] NOTICE[16648][C-00000022]: Ext. 912025551212:1 @

I have an asterisk box at a remote location (which I will call remote), which registers to my local asterisk box (I'll call that one local), and uses that to route calls to the outside world. The problem I am having is that the remote location needs to lie about it's callerid sometimes, however if I set a callerid that matches the extension of another peer that exists,

i have posted this before but was unable to resolve it. i have some new info so i figured i would try again. the trace from bandwidth.com are below. they are telling me that the ip that is bold should be our ip not bandwidth.com. i have changed every setting that i can see and nothing fixes this. Where would i change this at? they cannot tell me. INVITE sip:+185993133333 at 216.82.224.202

Dan Cropp wrote: > I had my screenshots flipped. Is there a way to make sure the Contact field is NOT included in the ACK response to the OK (for the Answer)? > > PJSIP is including the Contact for the ACK response to the OK. > Contact:<sip:1234 at xxx.xxx.xx.xxx:5060> > There is no configuration option to configure this behavior. What is the full SIP signaling? -- Joshua

I have ekiga registering to a voip provider (skypho) and receiving external call through the stun server. I want to redirect inconditionally all these calls to my asterisk server, but I can't understand how and what should I configure in asterisk in order to accept the redirected call. In asterisk console I can't see nothing when ekiga passes the call. If I turn asterisk's sip

ping times are fine as well: [root at freepbx asterisk]# ping sipgate.de PING sipgate.de (217.10.79.9) 56(84) bytes of data. 64 bytes from sipgate.de (217.10.79.9): icmp_seq=1 ttl=57 time=46.7 ms 64 bytes from sipgate.de (217.10.79.9): icmp_seq=2 ttl=57 time=46.4 ms 64 bytes from sipgate.de (217.10.79.9): icmp_seq=3 ttl=57 time=46.7 ms 64 bytes from sipgate.de (217.10.79.9): icmp_seq=4 ttl=57

Hi, I have a client using Mitel 5212 phones in SIP mode with a 1.4.21.1 Asterisk server (and a couple of previous 1.4 versions). They're mostly happy with the combination except for this one issue. For incoming calls only, either originating from other local SIP phones or from a PRI, calls won't get bridged (remote party get's hung up) if the call is answer too quickly on the

Hello all, I HAD video working before I upgraded to 1.08 (latest stable with Gentoo) and now it won't work. I just see noise bars and not the video. I know the camera works as I can use it in other programs such as AIM & Yahoo. I have the following setup: sip.conf [general] videosupport = yes port = 5060 ; Port to bind to (SIP is 5060) bindaddr = 0.0.0.0 ; Address to bind

Hello List- I'm having a problem getting snom 190 phones to transfer a call to another local extension. Here is the scenario: A call (call1) comes in from the PSTN to (exten1). (via pri, if that matters) Another call (call2) comes in to (exten1). (call1) is put on hold while (call2) is answered. (call2) is then transferred to (exten2) using the "Xfer" button on the snom phone. This

Hey i have an interesting topic to discuss here. The main goal here is to be able to make a video call between two WebRTC endpoints registered on asterisk 13 it is a feature that definitely asterisk 13 should support . the problems that i faced with this is the following and i hope i could get an advise here. asterisk 13 vanilla version has some issues marking the video packets this complain

Hi, I have 2 systems (A and B). I have an 800 number... when someone calls the 800 number it goes: IAX2-->A---IAX---B--->SIP PHONE However.. if the user calling the 800 number is a SIP user that is registered to A it goes: SIP--->A---IAX---B--->SIP PHONE This is the problem... when a call comes in from the IAX2 800 provider, things work fine... however if a SIP user registered to

Skipped content of type multipart/alternative-------------- next part -------------- A non-text attachment was scrubbed... Name: zaptel.conf Type: application/octet-stream Size: 34 bytes Desc: not available Url : http://lists.digium.com/pipermail/asterisk-users/attachments/20070508/f4c36cab/zaptel.obj -------------- next part -------------- A non-text attachment was scrubbed... Name:

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all! I'm trying to connect to ekiga.net through a client connected to my Asterisk server. For it I am being based on this [1] document. Next I put the configurations that I am using. /etc/asterisk/sip.conf: ; Outgoing to ekiga.net [ekiga] type=friend username=MyUser secret=MyPass host=ekiga.net canreinvite=no qualify=300 nat = yes stunaddr =

I have the following scenario: PSTN gateway (202.180.nnn.nnn) -> OpenSER 1.0.1 (147.202.nnn.nnn) -> Asterisk 1.2.16 (203.89.nnn.nnn) When an incoming call is received, often (but not always) Asterisk repeatedly sends a SIP 200 OK message and eventually hangs up the call. sip.conf [general] port = 5060 ; Port to bind to (SIP is 5060) bindaddr = 0.0.0.0 ; Address to bind to (all

hi, let me explain in detail, what i have configured and what is happening now: 1st router w724v (Deutsche Telekom AG): - port forwarding, everything to destination port 51000-55999 to device with ip 192.168.2.50 (interface of 2nd router) 2nd router Bintec RS353j): - configured NAT, everything to port 51000-55999 to device 192.168.3.99 (same ports) other direction is totally open. I

Hi, I'm trying to setup snom 710 phone with asterisk 13 with PJSIP. inbound is working fine but i cannot dial out. i don't hear anything on the phone and asterisk CLI also does not show anything. my config is. please advice. [2001] type=endpoint context=out-local disallow=all allow=ulaw allow=alaw transport=system-udp auth=2001

im having a strange problem related to call-limit for peers. well im not sure if its related to call-limmit or not. Bottom line is: I call a user A, from user B. user B hears silence, untill it goes to voicemail. when user B hangsup. user B's call limit is reset to 0 but user A's call limit is not reset.strange thing is user A's status on cli is shown as NOANSWER, while user B did not

Hi! I'm trying to set up a SIP trunk so that I can test calls, etc., between a new Asterisk box, and an old 1.4 box. --------------------------------------------------------------------------- New box: root at asterisk1:/etc/asterisk# head -1 sip.conf #include siptrunk.conf siptrunk.conf: [box1] ; All box1 extensions; see extensions.conf type=peer context=adhearsion host=172.17.0.17 ; IP