similar to: chan_modem_i4l delay again..

Hi, I currently use? Asterisk 1.0.7-BRIstuffed-0.2.0-RC7k on a debian sarge with a kernel 2.4.27 on a P4 3Gig with 1Gig of memory When i use i4l on any call, the called party ( on the telco operator side ) ear me with a delay of 1 sec after 1 minutes , 2 sec after 3 minutes and so on... After a quart hour, the delay make the conversation just

Hello all, I currently have an Eicon Diva Client isdn card using i4l. Outbound dtmf doesn't work (and never has), but there has been an annoying problem with false dtmf detection in calls (that could be triggered easily by blowing into the receiver on the remote end). I looked through the list and found two patches that need to be applied - 1 to isdn_tty.c in the kernel, and another to

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 I'm having some problems using the asterisk modem driver with an ISDN4Linux card (AVM Fritz). (I realise that it's better to use CAPI, but unfortunately this card doesn't have any CAPI drivers). Every so often the ISDN just stops working (it neither dials out nor accepts incoming calls). Trying to dial out just logs: --

The card is an ASUSCOM ISDNLink PCI (passive) and the circuit is from Qwest (in the US). I will be using this circuit only for voice (I'm doing this because of the poor quality of my POTS lines). I've compiled Hisax (as a module) into my 2.4.25 kernel, and with 'modprobe hisax type=35 protocol=4 id=hisax' I get the following: Apr 7 10:34:24 dev kernel: HiSax: Linux Driver for

I have asterisk loaded and seemingly working with 4 snom 200 phones. I cannot dial in or out using a DIVA isdn card When I dial out i get "not found xxxxxxx" on the handset. When I dial in i see in /var/log/message isdn_net: Incoming call without OAD, assuming '0' isdn_net: call from 0 -> 0 1856 ignored isdn_tty: Incoming call without OAD, assuming '0' isdn_tty:

Hello, I acquired a Diva Server 4BRI for an AsteriskPBX system and installed a 2.4.20 kernel modified with the latest eicon capi2.0 support from www.melware.net. Capi support seems to work fine: Asterisk+chan_capi answers the calls. However if I try to use my old isdnutils apps by loading a i4l compatibility layer then I have the following problems: - if I use the diva2i4l module and start the

Hi, I have read the wiki entries on IAX(2), but I'm afraid, it still have some questions: I have a working connection between two Asterisk-Servers (Asterisk 1.0.7-BRIstuffed-0.2.0-RC7k on Debian 3.1) via IAX. Does this connection work with IAX or IAX2? When I try to load chan_iax2.so, I get the error message chan_iax2.so]Oct 11 10:09:52 WARNING[2288]: loader.c:258 ast_load_resource:

Hello, I'm trying to understand why when I make a call from a SIP phone to an external number who has an IVR system in which I've to choose some options using the dialpad, it does'nt recognise the key pressed and remains still waiting for my choose. I'm tryng using Grandstream 102, and i've tryed with all the 3 modes possibile: Dtmf inband, rfc2833 and INFO (obviously

Hi, I had problems described in another thread so went from a start, but now have problems when loading qozap module. I get : # insmod qozap.ko ports=9 insmod: error inserting 'qozap.ko': -1 Unknown symbol in module and in /var/log/messages: module qozap unsupported by SUSE/Novell, tainting kernel. qozap: disagrees about version of symbol zt_receive qozap: Unknown symbol zt_receive

Hi, I am using Asterisk on a DSS1 ISDN-BRI with ISDN4Linux (and a Fritz Card PnP). The ISDN-BRI is in PTP-Mode (Point to Point "german: Anlagenanschluss") which is enabled within I4L with "hisaxctrl fcpcipnp0 7 1". Everything works fine except that I can not see the called number/MSN of incoming calls within Asterisk and because of this I can not route incoming calls

Hi, I'am having some problems with new mainboards and 3xHFC-S cards. The the first problem was with interrupts, I mean if HFC-S card was using interrupt i.e. 21 or higher - it didn't work. Solved by disabling APIC. However, still the driver behaves a little bit strange. If card 0 & 1 is TE and 2 is NT, TE works fine, but NT is not working at all. If card 0 is NT and 1 & 2 TE - all

Hello, Is there any way to specify which pubkey has rights to use the sftp-server subsytem when this has been set up in the sshd server? I don't know if I could control which users are authorized to use the sftp-server, could I? Is there any official patch that allows sftp-sessions 'chroot'ed? Thanks in advance. -- Best regards, quart mailto:quart at

Hi, I want to use the cdr to record the call log to my Microsoft SQL Server using unixodbc and freetds.... but when I compile, I've got this message.... Does anyone have the same problem and/or know how to solve it ? Thanks Baste regards David Masure make[1]: Entering directory `/usr/src/asterisk/bristuff-0.2.0-RC7k/asterisk-1.0.6/cdr' gcc -pipe -Wall -Wstrict-prototypes

Well, it has been a long time since I used my NetJet S cards with asterisk (moved to the quad PRI card) but I am trying to get this working again for home use. Basically, what I am using is this: Linux 2.6.8.1: config lines: # ISDN subsystem CONFIG_ISDN=y # Old ISDN4Linux CONFIG_ISDN_I4L=y # CONFIG_ISDN_PPP is not set CONFIG_ISDN_AUDIO=y # CONFIG_ISDN_TTY_FAX is not set CONFIG_ISDN_DRV_HISAX=y

Hi all, this is a rather "newbie-oriented" question, so please bear with me... The system running Asterisk has been provided with an AVM FRITZ!Card PnP. SuSE Linux 9.0 recognizes it right after booting the system and it seems to be configured (MSN) correctly... The hwinfo looks like this: --- pbx:/etc/asterisk # hwinfo --isapnp 11: ISA(PnP) 01.0: 10300 ISDN Adapter [Created at

Hello, I just got my isdn-card working together with i4l and asterisk. Everything seems to be working fine: I can accept calls coming from the outside and I can dial out. Even setting the msn works like charm but my problem is that I cannot hear a word. There's complete silence in both directions. Any idea what could be the cause? Thanks for your help, Gunther Lspci: 0000:01:07.0 Network

Hi all, My BRIstuffed 0.2.0-RC7k is running fine on my debian box for voice calls over ISDN2. Now I want to implement receiving incoming faxes into my setup so I did a google and some reading on the wiki. I got the spandsp 0.0.2pre10 package compiled and installed, patched asterisk's apps makefile and compiled * again. This all worked out fine. When integrating the RxFax into my dialplan the

I have a Samba server in a SuSE Linux 10.1 installation (x86_64 P IV), installed from SuSE RPMs (Samba 3.0.22). In our test instalation all our clientes works without problem, but from time to time, our users with Windows XP Service Pack 2 get a extrange error when trying to access or write some files. We have isolated the problem to shared folders that have a read and/or write list. We have this

Hello! Im pretty new of asterisk world: my goal would be using iaxcomm to call ppl over POTN. Yesterday i configured asterisk to be able to hear a song (with Playback() command) with iaxcomm, and it was wonderful. Now, today i tried to configure asterisk to use my ISDN4Linux supported card (a plain HFC card) with asterisk. i configured modem.conf this way, after reading

Hi all, does anyone have capiECT working? I can't get it to work - please see my logfiles below. While using an * CVS version of late September and chan_capi-0.2.5 (I guess), it worked!!! (I know, never change a running system ... should've backuped ... etc.) Here's the setup: NT----AgfeoISDNPBX----AgfeoISDNPBX----AnalogPhones in between the two PBX I attached my * server with a