similar to: Span monitoring

My TE411p does not seem to like to have two PRIs from different telcos (span 1 and span 2). I can get one working, but not the other. However, if I use vpmsupport=0 when loading the wct4xxp module, they both work. But here is the problem, vpmsupport=0 disables the on board echo cancellation. Any ideas? BTW, here is zaptel.conf span=1,1,0,esf,b8zs span=2,2,0,esf,b8zs bchan=1-23 dchan=24

Anyone tried the digium TC400B transcoding card? What are your opinions? Thnx

I am use Fedora 3, and run into a 1.4 compile issue. When 'make install' I got this message. [root@asterix asterisk-1.4.1]# make install make: expand.c:489: allocated_variable_append: Assertion `current_variable_set_list->next != 0' failed. make: *** [utils] Aborted [root@asterix asterisk-1.4.1]#

Hello my friends, I would like to understand the output from "pri intense debug span X", the Telco always says that their side is OK, but i always receive alarms, loosing connection, take a look: [Sep 16 13:18:19] WARNING[30364] chan_zap.c: Detected alarm on channel 1: Recovering [Sep 16 13:18:19] WARNING[30364] chan_zap.c: Unable to disable echo cancellation on channel 1 [...] [Sep 16

Hi all, I am handed a project to setup *. The requirement is that it can handle 8 T1s. Half of the calls coming into the system will be routed to SIP extensions (with transcoding). The machine we have in our disposal is a new dual Xeon 3.2gHz server with 2g of ram and an dual 1000mb nic. Voice will be coming in from the PSTN (through 2 quad digium cards) in g711ulaw, and most of the time will

I receive this error on the asterisk console and it is pretty much ALWAYS coming up. Sometimes there will be a break where it does not display. We had our PRI provider test the lines and they claim that there is no signalling problem. It doesn't matter if there are no calls or if there are 10 calls in progress the error is still displayed. I also get an annoying popping or clicking sound

I found one of UPS has a ups.alarm : Battery charger fail! Internal UPS fault! Is there a way to monitor for this kind of failure? In upsmon I did not find and event type for alarms like this... Thanks Adam Pribyl

I have a X100P and a TE110P in my Asterisk box. I can either get the X100P or the TE110P to work, but never both. Here's my zaptel.conf span=1,0,0,d4,ami e&m=1-24 fxsls=25 When I load wcte11xp and wcfxo, I will get this error. [root at asterix etc]# modprobe wcte11xp ZT_CHANCONFIG failed on channel 25: No such device or address (6) /lib/modules/2.4.20-8/misc/wcte11xp.o: post-install

We have an old Telrad 128KSU PBX to which I am trying to connect asterisk in the following manner: Current Setup: Telco-> T1->PBX Desired Setup: Telco-> T1-> Asterisk-> T1-> PBX. I am first trying to setup the Asterisk -> T1->PBX part without disturbing existing setup so I can get asterisk to forward calls to PBX and once that is done, I would try to move the telco

Hi, In Asterisk, what happens to the files when both legs of the call hangs up? Is there a way to create a conference room on the flight? i.e. without pre-defining the conference ID in meetme.conf. Thnx much. -------------- next part -------------- A non-text attachment was scrubbed... Name: winmail.dat Type: application/ms-tnef Size: 2872 bytes Desc: not available Url :

Hi all, I am setting up a script to record all the call. There are two app for recording. "Monitor" and "Mixmonitor", one mixing the audio on the fly and one mixing it at the end but also allow a option not to mixing the audio at all. If mixing the audio on the fly is not that taxing on the CPU, I would like to use 'mixmonitor' app. My question is, what is penalty on

Hello, If I put two spans' worth of channels, say 1-23 from span 1 and 25-47 in span 2, in one group, but only span 2 was showing OK and the other was down / showing a RED alarm, would asterisk automatically skip over trying to use channels 1-23 when doing outbound calls? e.g., dial(dahdi/g1/(number) would just jump to channel 25? Testing seems to bear this out, but I'm not positive

After working fine for a week or so my new Quad E1 asterisk 1.8 system has started rejecting outbound calls from the Nortel BMC 450 it is connected to. The cli fills up with these: sig_pri.c: Ring requested on unconfigured channel 255/255 span 3 Is this likely to be a 1) config error 2) cable issue (I made them) 3) hardware problem with the Digium card 4) software (lib pri) Any clues?

Hi folks, In the company where i work, we are implementing a security standard. A part of this is a log monitoring and reporting software. There are a few requirements, that the software must fulfil: - It must be capable of collecting logs from different devices (Linux machines, network equipment, ...). - it must be capable of sending alarms on security events - it has to generate daily (weekly,

About every hour I see the yellow alarms on all or a number of channels of my PRI which is connected to the dutch telephony network, Asterisk keeps on working fine.... Here's an example where channel 1-24 went into alarm: WARNING[90124]: File chan_zap.c, Line 4139 (handle_init_event): Detected alarm on channel 1: Yellow Alarm WARNING[90124]: File chan_zap.c, Line 4139 (handle_init_event):

We are having line noise issues in our Asterisk to legacy PBX integration. All SIP calls originating from IP phones sound crystal clear. All calls that originate from the legacy PBX (Isoetec 228) and route through the Asterisk and out SIP have a lot of line noise. I believe I have it pinned down to these Blue Alarm errors that I can see on the legacy PBX side. zttool shows no alarm but when I

All, One of our customers is using a Telrad PBX, we are providing phone server through asterisk via a T1 using e&m directly connected to the Telrad system. We're using a T1 cross cable as normal, the T1 part works great. No alarms. When we try and dial out the Telrad using a direct trunk group, the call fails. When looking in the asterisk console I noticed only 1 or 2 digits are seen,

hi,all i have just set up asterisk 1.6.0.7 rc1 with spandsp 0.0.5 pre4 to ReceiveFAX, link to a E1 (DE410P) using dahdi this can receive the fax from E1 successfully, but i see many error message in the log like this: [Mar 16 09:24:38] ERROR[23540] channel.c: ast_read() called with no recorded file descriptor. when i receive a 5 pages fax, i will see this error message over 200 lines..... it

Hello! I am trying to configure my digium TE220 dual-span pci express card with Dahdi. I seemed to have managed to set up the card with the Dahdi kernel, as demonstrated by executing dahdi_scan: [1] active=yes alarms=RED description=T2XXP (PCI) Card 0 Span 1 name=TE2/0/1 manufacturer=Digium devicetype=Wildcard TE220 (4th Gen) location=Board ID Switch 0 basechan=1 totchans=31 irq=16

Hi, After an upgrade, I discovered yesterday strange things I would like to share here. Basically, I'me comparing platforms: The first one is a 2.6.26 (Debian Lenny) platform, with Asterisk 1.6.1.18, Libpri 1.4.10.2, Dahdi revision 8853 (must be between 2.3 and 2.5, I think). The second one is a 2.6.32 (Debian Squeeze) platform, with Asterisk 10.5.1, Libpri 1.4.12, Dahdi 2.6.1. Both are