similar to: An FXO version of IAXy?

Hi list, I'm trying to get ready the MP-104 FXO to use qith my box, but when I send calls I hear only dial tone and after a few seconds I get busy signal. I very appreciate your advices. Command line results and SIPconfigurations follows: *CLI>* -- Executing [7991696900 at total:1] Playback("SIP/101-09dd8918", "beep") in new stack -- <SIP/101-09dd8918>

Greetings; We are trying to get Asterisk up and happy at our site-we tried VOIP using Sphere about a year ago, spent a *boodle* on expensive hardware and services from a local "expert", but it never was happy. I'm brand-spanking new at VOIP, and I've learned a *ton* getting Asterisk breathing in the last couple of days. I have three Polycom Soundpoint IP 500 SIP phones, which

I was able to setup AudioCodes MP-114 to rote calls form FOX to Asterisk and make internal calls: Routing Tables -> Tel to IP Routing: *, *, 10.0.0.109 (my asterisk IP) But I'm not sure how to setup AuioCodes to make calls out via FXO? In extensions.conf [Globals] pstn-5665=10.0.0.157 Whenever, I try to call out I get a busy signal. -- Joseph

Hi! I'm really hope you can help me solve a little mystery, the mystery is probably just my misunderstanding ! sorry... I've got an iaxy talking to my * box which connects to two providers. I'm running the stable release of the pbx. The only thing is that when dialling from the iaxy the ringing tone isn't heard while calling someone - you just hear silence then, they either

Is the Sipura 3000 the only way to interface a remote pstn line and connect incoming calls to Asterisk? I have a location connected by network that has a phone line, when the room is occupied I want the line ti ring there as normal, but when the employee is travelling I want the line to be conencted to a ATA that then feeds it as an incoming pstn line to the pbx located at my office so it can

I can't seem to get this device to grab an ip from dhcp. We have a working dhcp server (unfortunately it is on Windows), but I don't show any leases requested by the iaxy. Anyone have any ideas? The ethernet and phone lines are plugged in before the device is powered. Thanks, Erik

Hi, I have three Iaxy devices (s101i) parts. Two of them seem to work fine. The third plays a loud repeating click sound when an analog phone is plugged in. I can provision all of them, and make calls to all of them. The clicking one will blink when a call is incoming, but no audio from the call can be heard on the handset, and the caller only hears silence. The same handset works on the

I've got the following setup: IAXy -> Dect Base Station. When you dial from a SIP phone (cisco 7960), the rings with very little delay. However, if you hangup it takes 3-4 rings after hanging up before the dect base station phone stops ringing. The same applies when an incoming call is directed from PSTN FXO -> Dect Base. Is there a fix to this I've looked about on voip-info but

Hello, I am very new to asterisk and voip in general and so far have managed to get the FXO card and a few sip phones working fine. My question is where does the Sipura SPA 2000 come in the picture? Can it be used as an extension (i.e FXS) ? Or is it to be used as a line (i.e FXO)? Or it can be used as both? My understanding is that its just like another ATA186. Is that true? I guess what I

I have been searching for a while and can't find anything specific like this. Here's is my setup: IAXy -- broadband network -- Asterisk -- TE110P -- Channel Bank -- POTS lines (FXO) Everything works fine except for the echo at the IAXy. There is no echo on the POTS end, so Asterisk is doing a good job of echo canceling. Is there any provisioning in the IAXy to do echo

I haven't seen much activity on the list concerning Digium's IAXy standalone FXS device. Are they worth $100 ? Do they integrate well with * as an extension's FXS ?

Hi all, I want to link three incoming Bell Canada centrex pstn lines (which currently go to an old norstar pbx) into asterisk. Can anyone suggest the most "painless" (i.e., "just works") way to do this? Has anyone used the D-link DVG-3004S four-port FXO-to-sip adapter, or the twice-as-costly Audiocode MP104-FXO-C3S? I know the Digium TDM400P or Sangoma A200 are options

Does anyone know of a 24 port ATA device that could be installed in a phone closet? Like a channel bank, but, instead of multiplexing onto a T-1 circuit, it would convert to SIP/RTP on a LAN connection. Thanks, -- Michael Welter Introspect Telephony Corp. Denver, Colorado +1 303 674 2575 mike@introspect.com www.introspect.com

I place a call from an IAXY to an IAXY device. INitially the calls show in the output of "show channels". Then after a few seconds the "show channels" command shows 0 active channels even though I am still talking on the channels. Any ideas on this? THanks, Jerry

Hi.. I have to setup an extension in a remote location that will use a cordless analog telephone.. I am looking at the IAXY to do this for me..Basically the data path will be as follows... [Asterisk] == (NAT) == {Internet} == (NAT) == ATA -- Handset Since there are two NAT boxes in the path I know SIP won't work.. I also don't want to move the Asterisk box to the internet side of the

For anyone playing around with IAXy(S100i) devices, I am making the following available: Windows IAXy Provision v1.00 This is a from-the-ground-up development of a means of provisioning IAXy devices using a Windows environment. For some users, being bound to Linux for IAXy provisioning is not viable or convenient in some cases. This application provides a GUI data entry for the various IAXy

Hi, I've got an IAXy, and provided it with connection data - unfortunately didn't provide a fixed ip address, but left with dhcp. Everthing went fine, and I could work a while with it. After a restart of IAXy, it didn't negotiate a new IP address, nor used the old one. I even restarted the DHCP server and cleared its cache. No success. I went to another office with a different

Hi all, I have a Soekris net4801-50 board with OpenBSD 3.9 where I've configured a dhcp server and tested it with a regular PC connected directly via a crossover cable with success. The problem comes when I try to connect my IAXy device instead of the PC. I can see with 'tcpdump -nettti sis1' that the IAXy isn't sending any packets to the dhcp server. I thought my IAXy was bad

In the mailing list archives, I found a message that indicates that the IAXy has the ulaw, alaw, and g726 codecs, but I cannot find anything official on Digium's site about it. The Installation Manual has an example iax.conf file that indicates the ulaw codec, so I know that one is good. But we are thinking about using the IAXy over a VPN, to replace our MultiVoip. alaw and ulaw are

I have a brand new IAXy I'm playing with. I do not get a dialtone on the phone, or any response at ll on the phone. No sound, no dialing, no ringing. The phone and wire are tested and known to be good. I think I have it setup correctly. When I give the iaxprov command I get this: #iaxyprov 192.168.1.90 iaxy.conf 02: c0 a8 01 5a 05: 11 d9 03: ff ff ff 00 04: