similar to: Feedback from VON expo!Infoon*HAandPolycomphone!!

Grrr. I'm using outlook web access and there's no way to do inline replies. Anyway... Gabriel. Using SER does not create a single point of failure. You install three SER boxes. Single point of failure gone. It does not take several seconds. If your phones are configured for SRV, and 2/3 of your SER boxes down, it takes about 2s. That's not bad for a 2/3 system failure. You can

> -----Original Message----- > From: Alexander Lopez [mailto:Alex.Lopez@OpSys.com] > Sent: Thursday, March 16, 2006 8:46 AM > To: Asterisk Users Mailing List - Non-Commercial Discussion > Subject: RE: [Asterisk-Users] Feedback from VON expo! Info on > *HAandPolycomphone!! > > > > > > "Q: What are the plans for HA? > > That's BS. Last time I

Without using Dundi or SER, any thoughts on the following anyone? Has something similar been implemented anywhere so as to me not having to horribly butcher code... 4 servers SIP1-4 User1 -- -- SIP1 -- \ / \ User2 ------ Go to register ------- SIP2 ----- Whereis? --> DB / \ / User3 --

Dear all, I am currently trying to configure a PBX make use of a multiple of outgoing lines, currently my extensions.conf looks something like below >> ; extensions.conf ; 20th October 2008 [globals] sip1=201 sip2=202 sip3=203 sip4=204 [general] autofallthrough=yes [default] [incoming_calls] exten => _89859715,1,Dial(SIP/201) exten =>

Hi all. I have 2 ip phones (Grandstream Budgetone): -budgetone1 -budgetone2 All two are connected to an Asterisk server. When I make a call from budgetone1 to budgetone2, I can speak with budgetone2 whith no problem. But when budgetone2 hangs up, budgetone1 does not play any tone (like busy tone). Budgetone1 seems to be still in conversation, but what conversation! Has anyone had a problem

Dear all, I'd like to know if there is a way for multiple asterisk servers to share a common SIP and/or IAX registry. The setup I imagine would be something like : - several asterisk servers called sip1.isp.com, sip2.isp.com, ... - a DNS alias sip.isp.com pointing to all the addresses (thus providing a round robin resolution on each server) - each SIP client would register with sip.isp.com

> "Q: What are the plans for HA? > That's BS. Last time I checked, Asterisk's support of SRV was > to only grab the first SRV entry. Period. If it doesn't try > any more SRV hosts after the first fails, just exactly how is > that redundant? This is for the phones to fail over NOT Asterisk, remember in this case Asterisk has died so no matter what order it

Hello list, my case is as follows: SIP1--asterisk--SIP2. SIP2 is IVR type device. SIP1 and SIP2 both use g729. When SIP1 calls SIP2, it hears the IVR, and prompt the SIP1 to punch the keypad on the phone. As suggested by you, I need to configure the SIP1 with out band dtmf mode , what is about the sip.conf, should I specify the SIP1 with demfmode=rfc2238 ? do I also need to make same kind

Hi All, Is it possible to make a IAX2 connection between asterisk 1.6.1.0 , and asterisk 1.2.14 ? i tried to use a IAX2 connection between version 1.2.14 and 1.6.1.0 but it gave an error - 1.2.14 End - Error Msg WARNING[8313]: chan_iax2.c:7103 socket_read: Call rejected by 147.120.203.71: No authority found 1.2 END , IAX.conf [trunk14] type=friend host=147.120.203.71 secret=test123

Hello All, I have 4 Broadvoice lines. If I call any of the lines it shows that is coming from the first line. exaple register=XXXXXXXXX1@sip.broadvoice.com:passwd:XXXXXXXXX1@sip.broadvoice.com register=XXXXXXXXX2@sip.broadvoice.com:passwd:XXXXXXXXX2@sip.broadvoice.com register=XXXXXXXXX3@sip.broadvoice.com:passwd:XXXXXXXXX3@sip.broadvoice.com

my sip phone registered on 1.6, when i dial 4567 from 1.6 version, it wont go to 1.6 voice mail. it says == Using SIP RTP CoS mark 5 -- Executing [4567 at sip:1] Dial("SIP/312-09f9a720", "IAX2/trunk10 at 147.120.203.98/4567,10,t") in new stack -- Called trunk10 at 147.120.203.98/4567 [Jun 1 11:01:18] WARNING[8178]: chan_iax2.c:8991 socket_process: Call rejected by

Hi, I am trying to write dial plan for sip to auto answer (auto attend) the incoming call to the sip phone. - If i call from sip1 to sip2 then sip2 should automatically answer the call and play some sound file. I am trying to do this but as new to the asterisk dial plan configuration , so not able Todo this. help me if anyone already done this setup. Regards Upendra. -------------- next part

Hi all, Seriously, I've tried to read everything I could find (& search for) on voip-info.org and other sites about this problem, but have been unsuccesful. Equipment: xten lite X100P Whitebox linux running Asterisk / AMP D-Link DI-804HV (VPN router) I have installed another DI-804HV at a second location and created a tunnel. For the computers behind that unit, everything works fine

Is it possible to split sip.conf into two files (sip1.conf sip2.conf)? I have an Audiocodes gateway with two FXO ports, and (according to info I received, and it appears to be correct) Asterisk find the peers based on their IP and not on their IP+PORT. Thus, Audiocodes with two FXO ports registered on the same devices (=> one single IP with different SIP ports), the last entry into my

Hello, I think I have encountered an odd bug in Siemens C460 IP/dect handsets, which is a bit annoying, and I'm not (yet) sure how to get round it without lots of hacks. Basically, on all external incoming calls, we set: exten => s,n,SIPAddHeader(Alert-Info: Bellcore-dr2) This causes handsets (i.e. Cisco 7960 / Grandstream / aastra) to set a different ring cadence so to differentiate

Hello, is it possible to rout ALL RTP Data over Asterisk, like SIP1 <---RTP---> Asterisk <---RTP---> SIP2 I know it seems quite useless. But I want to simulate a IAX -> SIP connection and have no Phonecard installed on my computer ;) Thanx, Kalle

Hello list. When using SIP DNS SRV to define a production Asterisk server with high priority and a backup Asterisk server with a lower priority on this DNS-server, will this work as follow : - production server is reachable, so registration of the IP-phone goes to this server - production server is unreachable, so registration goes to the backup Asterisk server - production server is

Hi All I want to do features as belows. user ---> call ( from telco) --> asterisk ---> IVR -- SIP 1. after that, SIP1 transfer to SIP2 (unattendant or attendant transfer). i want to SIP1 hear stream sound data of call conversation between user and SIP 2 (don't used call conference) SIP3 want to hear stream sound data of user and SIP2 conversation, can be press DTMF

Hi All I want to setting as belows. caller ---> call ( from telco) --> asterisk ---> IVR -- SIP 1. after that, SIP1 transfer to SIP2 (unattendant or attendant transfer). i want to SIP1 hear stream sound data of call conversation between caller and SIP 2 (don't used call conference) SIP3 want to hear stream sound data of caller and SIP2 conversation, can be press DTMF

Hello, I am experiencing weird problem in Asterisk 16.2, possibly a bug. Same thing works fine in Asterisk 11. Here is the situation: I have 2 extensions on 2 phones. 4 extensions in total. phone 1: 8882 8382 phone 2: 8884 8384 And I have 2 SIP trunks for outgoing calls. I want to call via SIP1 when called via 8882 or 8884, and SIP2 when called via 8382 or 8384. And one last detail. SIP1