Displaying 20 results from an estimated 300 matches similar to: "misdn problem"
2006 Jun 08
1
BN8S0 problem - Extension can never match, so disconnecting
hi
i've configured a Beronet BN8S0 Card with misdn beronet utility.
the card is configured with all lines in TE and P2P mode, and it is
connected with the special cable with an ISDN connection.
i've turned on debugging to level 4, this is the output from the
asterisk cli when i receive a call:
P[ 5] MGMT: Short status dinfo 1000001
P[ 5] MGMT: SSTATUS: L1_ACTIVATED
P[ 5] handle_frm:
2009 Feb 06
1
set caller id on outgoing calls through BRI ISDNlines
Use Set(CALLERID(num)=9999999999) instead of using CALLERID(all).
Remember to set this BEFORE you Dial.
-->> -----Original Message-----
-->> From: asterisk-users-bounces at lists.digium.com
[mailto:asterisk-users-
-->> bounces at lists.digium.com] On Behalf Of Vieri
-->> Sent: 06 February 2009 12:36
-->> To: asterisk-users at lists.digium.com
-->>
2009 Feb 06
1
set caller id on outgoing calls through BRIISDNlines
You're quite right. We'll need to see your misdn.conf file to check the
settings.
-->> -----Original Message-----
-->> From: asterisk-users-bounces at lists.digium.com
[mailto:asterisk-users-
-->> bounces at lists.digium.com] On Behalf Of Vieri
-->> Sent: 06 February 2009 13:49
-->> To: asterisk-users at lists.digium.com
-->> Subject:
2006 May 11
1
mISDN trouble with a HFC Cologne card, Asterisk Asterisk 1.2.4 on Linux 2.6.16.11 - incoming DTMF detection
Hello everyone. I've got this really annoying HFC Cologne card (or
however I should call it - a single channel ISDN card based on the HFC
chipset).
It wrongfully detects lots and lots and lots of incoming DTMFs, to the
point the card is not usable.
Here's a sample out of CLI:
P[ 1] I IND :DTMF_TONE oad:206361 dad:520101
P[ 1] --> mode:TE cause:16 ocause:16 rad: cad:
P[ 1] -->
2005 Feb 04
1
*, BeroNet BN4S0 and misdn - problems
Hi,
i use an BN4S0 with misdn an asterisk on Linux 2.6.9. The hfcmulti module
is loaded with option:
type=0x04 protocol=0x2,0x2,0x22,0x2 layermask=0xf,0xf,0xf,0xf
and the fourth port is connected to an ISDN PTMP (MSN) port.
Call to #72 from S0 (BN port 4) are not accepted from asterisk but why ?
Can anyone give me a hint ??
misdn debug messages follows:
lib: NEW_CR Ind with l3id:80001
2008 Nov 05
0
b410p mIDSN - RNIS signaling problems
Hi.
I'm running Asterisk server with 10 sip phones, and 2 grouped T0 lines
with 10 DDI numbers.
My provider is France Telecom and my setup is :
- Debian Lenny
- Asterisk 1.4
- Linux kernel 2.6.25.17
- mISDN 1.1.8 driver
- Sip phones Thomson ST2030
No problem with the SIP .
But when reveiving a call on RNIS line (any of the DDI numbers), the
associated SIP phone rings indicating _two_
2010 Jun 10
2
ISDN -> SIP
i am using asterisk 1.6.2 with mISDN and a passive AVM Fritz!card on
CentOS 5.5. The only thing, i want to do is a call-redirection from an
isdn-call to my mobile via sip-account.
My extension conf is:
general]
static=yes
writeprotect=no
[globals]
OUT_PORT=1
[ISDN]
exten => 12345,1,Dial(SIP/012346737222 at sipprovider.local)
If i call to the msn 12345, the SIP-call is going out, but after
2006 Apr 28
1
mISDN: No DID/extension information returns busy to caller
I'm running a setup with chan_misdn on a austrian PTP-line. When
somebody dials in without an extension, he gets a busy signal.
I don't see the call at all in asterisk.
I *have* set immediate=yes in misdn.conf. And I *do* have an s-extension
in my dialplan for the context used by misdn. Calls that provide an
extension work fine.
Attached is my misdn.conf and a verbose 3, misdn set debug
2005 Jun 03
0
Anybody knows how to setup chan_misdn incoming calls
Hi.
I want to handle incoming chan_misdn traffic by asterisk, but I've got
message - 'Extension can never match, so disconnecting'. What I'm doing
wrong ? How I can pass incoming dialed number (dad) to misdn context (in
my case 'dss1_incoming') ? Works unrouted calls (s extension) if I set
immediate=yes in misdn.conf, but I want to route calls by dialed number.
log
2009 Feb 06
0
set caller id on outgoing calls through BRI ISDN lines
I'm trying to set caller ids on outgoing calls.
I have a quad BRI B410P card connected to my telephony provider.
I know the list of DID numbers the provider assigned to my company.
If I don't set the caller id then the callee always sees the same "top-level" number.
If I set the caller id to a specific DID number we own, the callee keeps seeing the "top-level" number,
2006 Mar 30
1
misdn timeout?
Hi all
I have a very strange problem here...
I use a hfc-s card with mISDN in NT mode with an ISDN Phone connected.
When I make a call, the phone rings two or three times and then misdn runs
into a timeout...
I don't know where to set that timeout, but it's way to short for the called
to pick up the phone.
If the destination phone is picked up, then everything is allright and the
2006 Apr 04
2
documenting s4 methods in package
Hi,
I have written a package that contains many s4 generic functions and
associated methods. I am having a lot of trouble getting R to build the help
pages for these generic functions without reporting, "missing link(s):
~~fun~~, which means that it cannot find the appropriate function when code
in the example section of the help is run. Right?
After some playing around I can get it to
2009 Mar 19
0
DTMF tones mid conversation
Just to add....
P[ 1] Transmitting 128 samples 2 misdn
P[ 1] writing 128 bytes 2 asterisk
P[ 1] Sending :160 bytes 2 MISDN
P[ 0] misdn_jb_fill: written:160 | Buffer status:256 p:861fee0
P[ 0] misdn_jb_empty: read:128 | Buffer status:128 p:861fee0
P[ 1] Transmitting 128 samples 2 misdn
P[ 1] writing 128 bytes 2 asterisk
P[ 1] PH_CONTROL: channel:1 oad2:07nnnnnnnnn dad0:820055
P[ 1] --> DTMF
2006 Feb 23
0
isdn problem
Hi
I have beronet BN8S0 isdn card in my asterisk and , card is working
fine, but when I try to dial to special number 118913 ( telephone number
information) from polish telecom TPSA, I always geting timeout .
Bellow is isdn signaling dump :
--> * CallGrp: PickupGrp:
--> rxgain:0 txgain:0
--> * dad:118913 tech:mISDN/2-u25 ctx:default
--> * Setting Context to from-tpnet
-->
2006 Nov 21
3
IAX access to FWD broken?
I hadn't used FWD for quite a while. A customer sent me an email last
week, "Is FWD broken when one tries to use it with IAX?"
I have been playing around, and indeed seems to be the case.
Is there anyone out there successfully using the two of them together?
Thanks.
B.
--
This message has been scanned for viruses and
dangerous content by MailScanner, and is
believed to be
2003 Sep 15
1
Anyone using National ISDN (NI-1) BRI under Linux?
I have a North American BRI configured as National ISDN (NI-1) on an
SBC (Nortel?) switch. SBC calls this "FastTrak ISDN", and it's
surprisingly inexpensive -- less than two POTS lines.
I've been trying to find an inexpensive PCI interface solution to
connect this to Asterisk as voice lines. I prefer ISDN BRI over POTS
lines because of the improved signalling, fast dialing,
2005 Feb 24
0
Connect to siemens pbx with misdn NT mode
Hi
I try to connect my asterisk with a Siemens Hicom pbx.
I have a PCI cologne Chip card wich support NT mode.
I have compiled mISDN driver, and I use chn_misdn from
debian package.
The card wotk fine in TE mode but mot in NT mode.
for informations :
routeur*CLI> misdn show stacks
BEGIN STACK_LIST:
* Stack Addr: Uid 40200001 Port 1 Type NT Prot. PMP
Link DOWN
--> bchan: addr 0 channel
2009 Jan 05
1
B410p, Ast1.4, France Télecom Numeris Double T0 problem
Hi.
When I call my RNIS numbers (with a mobile phone for example), I can
see 2 incoming calls on the IPBX, which should not happend.
I'm not sure if it's a problem with the telco France Telecom and their
ISDN setup, or if it's a problem
with the MISDN driver on the IPBX itself.
I'm stuck ...
Any advices for troubleshooting that?
Someone provide working configuration files
2006 Nov 05
1
asterisk DTMF detection
Hi,
Hi All,
I've just delved into the world of asterisk and I'm having a few dtmf issues.
Internally, amongst sip phones, dtmf is fine.
Externally, if you ring from a GSM mobile, DTMF is fine, however if
you ring from a standard phone, DTMF fails to register.
I am attempting to use a quad port HFC-4S Beronet Card. I've been
searching the web most of the last week and
2007 Jul 24
0
mISDN & Asterisk 1.4: HFC-S card not responsive
Hi,
I have installed Asterisk 1.4 with mISDN with the
install-asterisk.tar.gz script from beronet.com. On my system I have two
cards, one a AVM Frit!Card Pci 2.0 and one HFC-S chip. I know both to
work well with mISDN on my system from a previous installation.
Now however, the AVM card works well at first glance, i.e. it
"registers" incoming calls and works through the asterisk