similar to: Junghanns, Germany ISDN settings

Hi all, is it possible to bridge a call between a Junghanns quadBRI card and a TDM400 in the same server? It should be I think, -- I am trying this and when an incoming call comes in, it hangs both up at the moment the bridge is attempted (and a subsequent 'qozap: dropped audio' error is show in the /var/log/messages) Any thoughts appreciated -- I've seen posts, but no clear

Hi all, I'm trying to get a junghanns QuadBRI to coexist in the same machine as a Digium TDM400P card (so I can run the ISDN lines in and bridge with analog phones plugged into the TDM). I'm having a problem loading the modules. If I follow the BRIstuff (0.3.0-pre-1l) install method.... it's to modprobe zaptel, then insmod qozap.o I'm on Debian 2.4.31. That works. But then I

Hi all, i'm trying to install Asterisk with Junghanns QuadBri ISDN card: I have followed all the instructions, and when I run "|ztcfg -tvv" I get | | Zaptel Configuration ======================| SPAN 1: CCS/ AMI Build-out: 399-533 feet (DSX-1) Channel map: Channel 01: Individual Clear channel (Default) (Slaves: 01) Channel 02: Individual Clear channel (Default) (Slaves: 02)

Does anyone test Asterisk 1.2.X + bristuff-0.3.X and TDM card? We can't get it to work. -David -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Julian J. M. Sent: Friday, March 31, 2006 1:44 AM To: Chris Earle; Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] Re: BRI

Hey, anyone know if it's possible to receive faxes through a Junghanns bristuff quadbri card? In germany, currently I have faxes coming in on DID line into QuadBRI and then passing to Digium TDM400 (analog) and into faxmachine. But the reliability of TDM card is spotty, so I want to maybe just accept faxes in on ISDN card and save on asterisk system ...? keeping digital signal strong ...

Hi everybody I hope that somebody can help me with the following .... I have 2 quadbri cards 2 - 1t0 cards 1 pabx alcatel 4200 I would like to connect my asterisk to the alcatel , I installed bristuff 0.3.0-1p , loaded the zaphfc driver in NT mode configured zaptel and zapata , it works great. then I removed the 1 t0 card, added the quadbri loaded qozap : insmod qozap.ko ports=15 ( 4 ports

I am unable to make quadbri board to work in NT mode, in TE mode it works OK. I have set 5 jumpers to NT mode. Dmesg shows everything OK: qozap: Junghanns.NET quadBRI card configured at mem 0xd084e000 IRQ 9 HZ 100 CardID 1 qozap: S/T ports: 4 [ TE TE TE NT ] qozap: 1 multiBRI card(s) in this box, 4 BRI ports total. from Asterisk side seems to be ok. pri show span 4 Primary D-channel: 12 Status:

Hi, I'm using Asterisk 1.6.1.18 with latest Dahdi Linux and Tools (rev 8854) and libpri 1.4.10.2. During installation, I'm facing this : # dahdi_genconf -v system Default parameters from /etc/dahdi/genconf_parameters Empty configuration -- no spans Of course, I've got span descriptions in /etc/dahdi/genconf_parameters : .... pri_termtype SPAN/1 TE SPAN/2

Hi, I'm trying to connect quadbri between powered ISDN phone and ISDN line: ISDN <---1---> TE - * - NT <--2--> Phone I use quadbri, suse 9.2 and latest 0.2.0-RC7k bristuff. I've used sample settings provided with package, but do get strange error (I think that I have wrong setting for P2P or P2MP setting and cables 1 and 2). If I connect phone to ISDN with straight cable

Hi, I'm trying to dial from one Asterisk box to a Patton 4638 BRI gateway. I'm only getting this : [May 8 15:08:24] WARNING[16797]: app_dial.c:1547 dial_exec_full: Unable to create channel of type 'DAHDI' (cause 0 - Unknown) My setup is : Asterisk 1.6.1.18 libpri 1.4.10.2 1 Junghanns QuadBRI PCI-E express with : - driver

Hi All ... I'm running Asterisk 1.2.13-BRIstuffed-0.3.0-PRE-1v which has a Junghanns QuadBri card in it (lspci reports Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] (rev 01)) I have a regular KPN ISDN2 Line connected which works fine with the the zapata.conf below. However, I also have a new KPN ISDN Mutli (meervoudig) line (PBAX-Group), which works fine for incoming calls,

Thanks. I think our problem ca be similar. Have you tried to call from analog phone #1 to another analog phone #2? It works. But when you try to call vice versa from #2 to #1 it does not work. When you restart asterisk it works again - but only one direction. -David ________________________________ From: asterisk-users-bounces@lists.digium.com

What happens if you take out the Zaptel I/F's? If it boots, you can correct whatever you did then replace them. hth -----Original Message----- From: Chris Earle (CBL) [mailto:cearle@cbltech.ca] Sent: Tuesday, February 28, 2006 7:45 AM To: asterisk-users@lists.digium.com Subject: [Asterisk-Users] Cannot boot machine up after working on zaptel.... Hi all, hard for me to explain this, but

Hey all, anyone know the status of disconnect supervision on POTS lines in India? Set up an asterisk box, TDM cards, in Mumbai, and doesn't seem to have disconnect supervision...... Thanks -- Chris Earle System Solutions Specialist

Hello, Is anybody there using quadBRI form Junghanns.net with Asterisk ? I would like to order that card but first would like to hear some opinions. Thank you in advance Bartosz

Hi all, Has anyone ever thought about or implemented a way to use Rails to pull content from a database and actually *generate* static html pages from view templates? I want to throw a bunch of content into a db using rails and then put all my website templates into the views dir and write the files out with the content inside. The funny thing is that the html pages Rails normally outputs to

Hi, I have an asterisk box with a QuadBRI. I am close to make it work like I want: Incoming calls to SIP are OK, outgoing calls are quiet working thanks to Michael Sandee advices. My real problem is that my * box is freezing very often when I probe qozap (bri-stuff 0.0.2). I have tried two distribs (Debian Kernel 2.6, Mandrake 9.1 Kernel 2.4) and it always work for a few minutes and freezes. At

Hi, I'm using a revision 6822-enabled Dahdi-Tools (see https://issues.asterisk.org/view.php?id=13897) with a Junghanns QuadBRI. 1. Do I still need qozap driver ? If positive, how is it recommended to get it ? 2. Which line should be included in /etc/dahdi/modules to have the appropriate driver loaded ? 3. The process I'm planning to use is : A- Hand edit /etc/dadhi/modules,

Good afternoon, I have to develop an Asterisk system in Spain that can support up to 8 simultaneos ISDN calls (4 BRI), initially only 6 simultaneos calls. I have been looking into VOIP-INFO and I found that the Junghanns card QuadBRI is a very good option. But when I look for a server to develop the system, the information is a bit more confuse. Any one have experience with this card? Which

Hello everybody, I've got Asterisk 1.2.4 running with two Junghanns QuadBRI cards using the qozap driver from bristuff 0.3.0-PRE-1l. One of the cards is running in TE mode, the other one in NT mode. Whenever I call into an empty MeetMe conference room on one of the NT ports or via SIP and hang up the call during the "you are currently the only participant in this conference"