similar to: Reverse group in zapata.conf

Hi, I am just trying to figure out how to setup a TDM04B card for incoming/outgoing calls. I have 4 lines, which are provided as a rotary trunk group, currently hooked into a Nortel system, which asterisk will replace. I have setup a Dell 1800 (Tower) system with the TDM04B card, which seems to work. The question is how do I set it up that all 4 lines are part of a trunk group, such that

Hi, If I have a PRI with all channels grouped in group=1, I understand when I want to make an outgoing call that asterisk takes the first channel available. Is there any possiblity to "rotate" the channel taken? I was searching in Wiki but I could not find nothing about. Thanks, Alejandro

I am perplexed by this so I how someone can help me out. On one of my servers the users began complaining that if they picked up a parked call they could not use the # key to transfer the call. This is a particualarly annoying issue since everyone has been taught to use #700 to park calls. At first I thought it was a DTMF issue with the polycom phones, since rebooting seemed to fix the problem.

Hello everyone, I'm sure someone had an experience arranging hunt-group setup for incoming calls on T1 PRI channels of Digium TE110P card. For instance, I have main DID channel associated with number (555) 222 0001. And I have whole bunch of other DID channels on same T1 card like (555) 222 0090, (555) 222 0091, (555) 222 0093. My goal is when a call comes to the main number which is

Hi, I recently got a TDM04B and after installing and getting asterisk up and running I connected a handset to one of the ports. Unfortunately I don't get a dial tone when I lift the handset. What could be the cause of this? Could someone point me in the direction of a proper config for a TDM04B? Thanks.

> -----Original Message----- > From: asterisk-users-bounces@lists.digium.com > [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of > Gordon Henderson > Sent: Friday, February 09, 2007 9:47 AM > To: Asterisk Users Mailing List - Non-Commercial Discussion > Subject: [asterisk-users] Conferencing Phones ... > > > Anyone got any experiences of good quality

Has anyone got a sensible zaptel.conf and zapata.conf for 2 TDM400P's working with UK set-up. They're set-up with 7 analogue phones and 1 PSTN port. Currently zaptel.conf has fxoks=1-7 fxsks=8 loadzone=uk defaultzone=uk It's really zapata.conf that would be useful. Currently using the zaptel/asterisk that comes with Ubuntu (latest) which needed a bit of tweaking (1.2.16), but could

Hi all, I'm running Asterisk 1.0.0. I am a customer ( and supporter ) of voicepulse. For me, it works perfectly, but one of my customers noticed a small problem: During a conversation, when the otherside isn't talking, it's almost like the mic turns off. Not that big of a deal I know, and the more I think about it, the more this seems a voicepulse issue. But in the off

When I try to patch the Makefile for asterisk with the Apps_makefile.patch from Spandsp I get the following error. patching file Makefile Hunk #1 FAILED at 47. Hunk #2 FAILED at 76. 2 out of 2 hunks FAILED Has anybody seen this.

Hi I posted earlier about having issues connecting to Telewest's ISDN, only to find out later Telewest had forgotten to turn it on - hopefully I'm not having a similar silly problem. My PRI span is now up and operational, but when I try to send a call out over it, I just get congestion tones. Occasionally, I get about one second of ring tones, only for it to cut out and play congestion.

Hello All !!! I have 4 PSTN lines in the PBX server 1,2,3,4. First line will be used by only one extension (i.e. for the boss) for incoming and outgoing. This line is dedicated for him only.( The remaining lines will be shared by the employees 1) Group A have access to lines 2 , 3 & 4. 2) Group B have access to lines 3 & 4 3) Group C have access to line 4

Hi, I'm trying to set a rule to dial out through multiple Zap groups so that, say, g0 is the cheaper POTS lines group and must be used first. However, if g0 is busy or disconnected then try dialing out g1. My g0 group is made up of 4 analog lines connected to a 4-FXO card. I disconnected the RJ-11 wires from the FXO card to simulate a line disconnection. So theoretically all calls should

Hi, Is there a way to create trunk groups while asterisk is running. For exemple let's say that zapata.conf defines g0 as channels 1-23 I would like (while asterisk is running) define g1 as 1-10 and g1 as 10-23 Any hints appreciated. Andre Courchesne

I've been trying to use a set-up whereby I have several TA's connected to an Asterisk server (1.2.4) and they act like they're in a hunt-group i.e. try the first, if busy jump to the next etc. in my extensions.conf I had something like [inbound-trunk] exten => 441234123456,1,Dial(SIP/s1a,20,r) exten => 441234123456,102,Dial(SIP/s2a,20,r) exten =>

I have a site running asterisk 1.2.8 with a hand full of polycoms and grandstream 2Kxp's. When a call is missed and you look at the missed call logs on either, its has the persons exten, not the incoming caller id. Any ideas? \\\|/// \\ ~ ~ // ( @ @ )--oOOo-(_)-oOOo? -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello! I've run into a problem where a user is making an outbound call at the same time that an inbound call is being made on the same analog line. It appears that as the zap channel is opened for the outbound call, it is simply answering the inbound call. Obviously, both parties involved in the calling get a bit confused. Previously, it happened only on an occasional basis. However, as this

Hello, I have two FXS port on my TDM card. channel 4 is attached with a telco line that I use frequently. And channel 3 have another telco line. but I dont publish that number to my friends. If I receive a call through channel 4, how can I handover that call to channel 3 ..so that I can keep channel 4 open for incoming call. Thanks,

Will the FXS cards that work with asterisk handle rotary? Are there any channel banks that can convert rotary to touch tone (like some sorta bridge)? The goal is to be able to log input from rotary phones. Full PBX functionality would be nice but... (It's for a project, not for serious production). -- // Ethan O'Toole //

try "sipsak -M -O desktop -B "foo" -s sip:<user>@<registrar> -H <ip of registrar>" the trick is to specify the "-O desktop" parameter + the "-H <ip of registrar>" parameter. Sipsak fakes the host-header of the registrar so that the Snom thinks it is coming from your Asterisk server, then lets the message through to the

Run /usr/src/zaptel/ztmonitor 32 -v And adjust your gains in /etc/asterisk/zapata.conf accordingly. Gregory P. Scasny Golden Technologies Inc. http://www.golden-tech.com 219-462-7200 -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of bam Sent: Friday, May 07, 2004 3:35 AM To: asterisk-users@lists.digium.com