similar to: run with incorrect E1/T1 jumper settings

Does anyone know if I could use modprobe command to find out rather than set the jumper on a Digium PRI card? I want to find out the jumper settings on the card without opening the box which will cause down time. Thanks. -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, Is it possible to monitor conversation of logged in Agents? Currently I am using ZapScan to monitor incoming calls, but I would like to monitor individual agents. raj

TE410P card down. I have three (3) TE410P in one machine running asterisk with SS7. My problems started last week when one of my cards started switching to E1 every time after reboot. I set the following in dahdi.conf and that solve the problem. /etc/modprobe.d/ options wct4xxp t1e1override=0x00 Now all 4 ports on that card is down with Red Alarm. I tried rebooting the machine and

Hello, In my system, dmesg outputs : [ 13.039788] wcb4xxp 0000:01:0a.0: probe called for b4xx... [ 13.039788] ACPI: PCI Interrupt 0000:01:0a.0[A] -> GSI 21 (level, low) -> IRQ 21 [ 13.039788] wcb4xxp 0000:01:0a.0: Identified HFC-8S Junghanns.NET octoBRI PCI (controller rev 1) at 0001dfe0, IRQ 21 [ 13.041202] wcb4xxp 0000:01:0a.0: NOTE: hardware echo cancellation has been disabled [

I do part time consulting work. I need to setup an asterisk system to allow me to record both inbound and outbound calls to clients. I have one client that is just a PITA. The client has changed their mind three times so far and we are at step one. I have a spare slackware box and a seperate phone line for the consulting work. I have MCI Neighorhood as my carrier. What I need to know is: 1.

Hi I'm trying to get a Digium TE110P card working but as soon as I load the module with modprobe wcte11xp the sound stops working for incoming calls (SIP and IAX). I haven't even started to configure the card. Running ztcfg and restarting asterisk doesn't help. After unloading with rmmod wcte11xp the sound comes back for new calls I'm using asterisk 1.2.4, libpri 1.2.2 and

I have a supermicro AOC-SAT2-MV8 and am having some issues getting drives to work. From what I can tell, my cables are to long to use with SATA2. I got some drives to work by jumpering them down to sata1, but other drives I can''t jumper without opening the case and voiding the drive warranty. Does anyone know if there is a system setting to drop it back to SATA1? I use zfs on a raid2 if

On 2020-05-08 1:34 p.m., Xun Li wrote: > Hi, > > I was looking into the implementation of TailRecursionElimination, and > noticed that we have the constrain that if any call uses a local, even > though it doesn't capture the local, it would still prohibit TCE. This > contain seems unnecessary and overly limiting? I think it's a necessary limitation. The idea is that

My old server was Centos 4.8 and it is on a HD that is NOT connected. The new Centos 5.5 is the active HD. Everything appears to be working, so my intent is to jumper the old HD as a slave, wipe it clean and have it as a backup drive. Since my Linux skills are minimum, I thought it best to heck with the experts to find the best (safest) way to accomplish my goal. I assume that the old

hi All I need your help , for used Digium Card TE405P, for setting this Board AS E1 ISDN PRI. 1 .Current for make sure my config its rights or no I inform my configurations in Board Jumper T1/E1 is Closed is that rights or no ? for E1 i closed the Jumper. 2. I Want To seeting E1 in ASterisk/PC Back To Back To Cisco E1 AS5300 Use ISDN Signaling, my configutration :

On 2020-05-08 2:58 p.m., Xun Li wrote: > Eli, > Yes I was referring to AllCallsAreTailCalls. I will take a look at how > to improve this. > > Nick, > Thanks. I agree that's the proper constrain to mark a call as > tailcall, however not being able to mark a call as tailcall shouldn't > completely kill TCE. (i.e. AllCallsAreTailCalls seems overly > limiting). I

Hi all, I've got a Junghanns QuadBRI card which I'm going to install on a system in Germany Anyone give me some tips on the Jumper settings? I'm guessing it's going to be NT mode with p2p? I haven't used ISDN before. I'm going to also put a Digium TDM400P card in there to plug the analog phones into. I'm just worried about the jumpers and modes. Suggestions

I am having problems with silent data corruption on (some) drives connected to an MCP55 SATA controller. I have two servers, both running RELENG_7_0/amd64. One has the 570 Ultra chipset, the other has 570 SLI. Both chipsets have the MCP55 SATA controller. The server with 570 Ultra chipset has a bunch of older 250GB SATA-150 drives hooked up to the MCP55 controller and it is working just fine.

Hello I am trying to configure TE420P but i am confused what to give chan_dahdi :( Below is configuration i am using for TDM400P Please help what changes to make in it... Please provide a link as well [trunkgroups] [channels] ;default for channels switchtype=national rxwink=300 hidecallerid=no callwaiting=yes usecallingpres=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes

Greetings, I have recently built two machines both with Intel VT technology CPU''s but when I try to create a hvm guest I get an error that the host doesn''t support it. Is there a compatibility guide I can consult on whether perhaps my motherboards are either not compliant or perhaps need a bios or jumper setting adjusted to enable hardware virtualization support?

To recap: T100P card wouldn't sync with the telco using line side clocking ( span=1,1,0.........) Had to use internal clocking (span=1,0,0.......) zttool showed Tx/Rx Levels as 0/ 1 For the grins of it I replaced the T100P card with another newer card from inventory. This newer card has the same rev on the ASIC / FPGA but doesn't have any of the various jumper headers installed

Hi guys, Currently I just purchased the TE205P for the installation of my ISDN30 setup. I compiled, setup the card correctly I think. When I do the ztcfg -vvv it shows all 31 channels clear, with 30 bchannels using for voice ranging from 1-15, 17-31, and 16 is the dchannel. However, when I do a cat /proc/zaptel/1 I see only 24 channels configured, and then, when I do a cat /proc/zaptel/2 I see

I'm trying to install CentOS 5.4 on a machine with a LSI SAS 1068E controller. I've googled all over the place and found a few different drivers for RHEL5 for it.. and tried a few of them.. Some will load, some complain that this isn't the correct version.. non of them work when it comes to showing Hard Drivers in the partition manager. The machine is a Supermicro SYS-6015V-M3

HI Can I install Centos on Segate ST3160812AS ( SATA II ) Harddisk? Asky

Hi, I'm trying to dial from one Asterisk box to a Patton 4638 BRI gateway. I'm only getting this : [May 8 15:08:24] WARNING[16797]: app_dial.c:1547 dial_exec_full: Unable to create channel of type 'DAHDI' (cause 0 - Unknown) My setup is : Asterisk 1.6.1.18 libpri 1.4.10.2 1 Junghanns QuadBRI PCI-E express with : - driver