similar to: problems while dailing outside

I am trying to set up a Grandstream GXV-3000 Video phone to Asterisk ver 1.2.21.1. The problem I'm having is that it can call other SIP phones, but not vice versa. Can someone tell me where is the problem? TIA! Here's part of my configurations: ---------- sip.conf ---------- ; 113 is the Grandstream phone [113] type=friend username=113 secret=secret context=default dtmfmode = rfc2833

Dear all I have asterisk setup now what happend when i dial 4 digit number my asterisk wait for few digit why when i press # key it is dialing fast but without # wait for few number is there any configuration for dialplan I have setup asterisk with avaya system i have 5 avaya system on 5 location i use 16XX,22XX,33XX,44XX,20XX to reach avaya extentions but when

I cant seem to get outgoing calls to be placed properly .. No matter what I try I get an error from the PSTN company saying that the "call can not be completed as dialed" or "you need to dial a one..." The asterisk debugging seems to show the correct number being dialed out of the zap interface... the "9" is being stripped and there is a "1" where it is

I'm Japanese. Sorry,English is not so understood,Please let me question by items. In Asterisk-1.2.1 and 1.2.2,I cannnot understand the operation of Authenticate application's 'j' option. exten => 123,1,Answer() exten => 123,2,Authenticate(789,j) exten => 123,3,Playback(pin-number-accepted) exten => 123,4,SayDigits(111) exten => 123,103,SayDigits(999) In this

I think I have it configured properly. ztcfg -vv shows it as channel 1 and zttool shows it as OK. But I can't dial out. When I try, it shows it arrive in teh right stack, but then issues the following errors: channel.c:1676 ast_request: No channel type registered for '{PSTN-1}' app_dial.c:554 dial_exec: Unable to create channel of type '{PSTN-1}' = = Everyone is busy at

I am using Polycom 501s with asterisk 1.2.4. When transfering to call parking wih "#1" -> 700 the user is able to hear asterisk tell him what extension the call was parked on. However, when I press "transfer" -> blind -> 700 . The user is not able to hear what extension the call was parked on. It seems like the polycom is hanging up before asterisk is able to

please help!!! I am dialing into our asterisk server(TDM400p) from the psnt. I hear our voicemail message and I press the extention 1000. The Polycom ip phone in the office rings. I pickup but neither side can hear one another. What have I done wrong? thanks sip.conf: [general] context=local-access ; Default context for incoming calls bindport=5060

Hi, I am setting up an asterisk server for testing purposes and cannot get voicemail to work at all. My host OS is Linux From Scratch 6.3 and the asterisk software versions I built are zaptel-1.4.5.1 and asterisk-1.4.12. I am using the Ekiga softphone on my Ubuntu desktop machine. My asterisk server and client phone are on different computers but are on the same LAN, i.e. no NAT. I have an

Hello... I have a big problem with asterisk. Every time i make a call asterisk does not bridge the zap channels. The zap channel from which i'm calling remains in state:ring and applicaton:dial and the zap channel with the external line configured remains in state:dialling an Application:AppDial. Zap/20-1 agentie s 1 Dialing AppDial (Outgoing Line) 09399 (None) Zap/9-1 int_omg 09399 5 Ring

Hello! I do not use sssd use winbind. When I mentioned in the lines workgroup and realm, they are like this (for example) Workgroup = INTRNAL Realm = INTERNAL.TESTE.COM.BR I do not know if that was what caused the confusion .... Thanks Em 08-01-2017 20:28, Rowland Penny via samba escreveu: > On Sun, 8 Jan 2017 20:04:41 -0200 > "Carlos A. P. Cunha" <carlos.hollow at

I am trying to configure Asterisk for BSNL, india network. I have successfully configured it for outgoing calls. When any outside number make any call to trunk then it receives the call properly but when the call is disconnected by inside extension then outside phone does not get a busy tone. Asterisk incoming call log: -- Executing [s at incoming:2] Dial("Zap/4-1", "Zap/1")

Hi all, i am stuck with the configuration of asterisk - modules are loaded ( zaptel and wct4xxp ) - i have zaptel.conf configure, output of ztcfg -vv --- snip -- rapid:~# ztcfg -vv Zaptel Configuration ====================== SPAN 1: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet (DSX-1) SPAN 2: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet (DSX-1) SPAN 3: ESF/B8ZS Build-out: 0 db (CSU)/0-133 feet

Hi all, I just installed chan_h323 to interface to a H.323/ISDN gateway. It works really well after two days learning and testing except one thing somebody of you may have an answer to: If I call in from PSTN to a busy asterisk SIP extension I can see a SIP status 486 BUSY, but don't get it passed to the H.323/ISDN side. Asterisk jumps correctly to EXTEN+101 in the dialplan. I tried

The following is my dialplan for outgoing international call. What I want are: - when people dial 9011604xxxxxxx , 9011605xxxxxxx, 90114411xxxxxxx, 90114421xxxxxxx, use voipstunt to dial out - otherwise, use my pstn to dial out. What I've found is when i dial 9011604xxxxxxx , 9011605xxxxxxx, 90114411xxxxxxx, 90114421xxxxxxx, it always use the pstn to dial out. Anything wrong with my dial

I am up to post 5 on my step-by-step but I hit a bit of a snag and so far my searches have failed me, I hope someone can help. (By the way, I added an asterisk index for quick navigation on the blog http://qvlweb.blogspot.com/2009/04/asterisk-pbx-install-index.html.) Here is the snag and I am hoping for a little help from the collective. Inbound I have 2 different numbers. I can call in on both

Hello group, I tried a lot to enlarge the frequency (i.e. more announces, low wait between). according to config, every 30 seconds the announcement should take place. In fact, the first periodic announce is done after 2 minutes? What is my fault? Thank you Regards Paul # zypper if asterisk Loading repository data... Reading installed packages... Information for package asterisk:

Hey, all. I'm trying to set my CID such that, internally, I see a four-digit extension (which is also handy when checking VM), but externally, I see the full 10-digit number. So I plugged these lines into my extensions.conf: exten => _XXXXXXX,1,GotoIf($[ ${CALLERIDNUM} != 1625]?4:2) exten => _XXXXXXX,2,Set(CALLERIDNUM=6031234${CALLERIDNUM:1}) exten =>

Hi List; Can someone advise me why in the below context, it does not run the Background step? Once I dial 1000, then it hangup and give congestion signal? If I comment the ResponseTimeOut, then it run the Background but it does not wait till caller enter the digits, once the sound file finish, then it hangup (congestion signal), also in all the situation, it does not go for the t extension, why?

Hello all: For fun, I am learning about Asterisk, and trying to get Asterisk working at my house. I installed Asterisk@Home. It seems to be functioning fine. I installed a couple of softphones, and have them registered with Asterisk. I actually work for a CLEC, and I have registered my Asterisk box with SER (which I don't begin to understand yet) at the office. In order to try to

I tried to add a couple of SIP phones (polycom 601s) to my existing asterisk installation. I can successfully make a call from the SIP phone to any other phone (inside or outside), but I can not make any calls to a SIP phone. Attached are the pertinent parts of sip.conf and extensions.conf. The log starts off normal with: Mar 26 09:51:15 DEBUG[4885] chan_zap.c: DTMF digit: 2 on Zap/55-1 Mar