similar to: SIP ATA gives no ring tone on IAX2 route

Hello! I migrated asterisk 11 to 13 as user of FreePBX 12.0.76.2. As customer of German Telekom, I have three numbers and therefore three trunks - each number is bound to one trunk. After migration, some callers complained about missing ringback tone: they didn't hear any ring tone and where surprised that they suddenly got me anyway :-). The connection afterwards was as expected. Deeper

Hi all, I'm using following software and equipment and I have very strange behavior: Asterisk CVS-NHEAD-05/30/05-16:42:41 H323 gatekeeper - GnuGK 2.2.2 IAX2 client - Firefly 1.9.8 build 3945 H323 client - SJPhone Build 1.50.271d H323 gateway - Welltech Wellgate 3504A When I dial from Firefly (IAX2) -> SJPhone (H323) everything works as expected. When I dial from SJPhone (H323) ->

Hi We've recently set up and are using with success 1.0.7 using a Junghanns quadbri card to BRI ISDN, and Firefly with IAX2 protocol as softphones Works very well, however we're getting cases where sometimes the call just drops. >From setting more verbose modes we get a log which is shown below. The problem seems to be the maxretries message which comes from chan_iax2. We are using

Hey everyone here's my problem. Have a queue configured, it plays the desired recording, checks to see if agents are logged in via agentcallback, forwards the call according to distribution method, times out according to timeout settings, logs out the agent that did not answer, hunts for next agent, logs the rest of the agents out one by one when they don't answer, and drops call into

Using Firefly 1.9.5 (thirdparty) on Win2k Using Asterisk CVS HEAD 20041117 (also tried with 20040806 and 200410-something) IAX2, no NAT. Firefly->Asterisk audio works, but I can't hear anything from the other side. Using GSM codec, also tried ulaw. Any ideas? -A. relevant bits of iax.conf: [andrew-bt] type=peer host=dynamic trunk=no [andrew-bt] type=user context=fxs secret=12345

Whoops, email client auto-filled dev previously. Let's try this again. Michael Maier wrote: <snip> > Ok - but this doesn't seem to answer my main question: > > Why must > > progressinband=never > > be applied especially if asterisk uses it by default? The big difference > between w/ and w/o it is: The default in 13 is "no" which still

Hi List; I am using Firefly softphone Version 1.9.9 Build 4521 and I select IAX protocol and did the configuration in Network1 (and I checked the Active checkbox) as following: Server: 192.168.8.4 username: iax2user1 password: password In the Asterisk, I did the following configuration on the /etc/asterisk/iax.conf: [iax2user1] type=friend context=internal username=iax2user1 secret=password

Hello everyone! I've had this problem for a while and cant figure it out. When an outside caller calls an extension on my asterisk system, they do not hear any sort of ringing. Inside extensions calling other extensions do hear ringing. We have 3 other asterisk systems that are configured the same way, but do not have this problem. We think it has something to do with asterisk 1.6. The other

Does anyone know how I can get stderr from AGI to be sent to somewhere other than the console? It seems that this is the only place it can go. Changing logger.conf has no effect. If you want to see errors from AGI scripts, you have to run the Asterisk console, which isn't viable. Doug.

I'm running Asterisk CVS-04/28/04-13:22:35 (fairly current) Today when I setup queues for the first time (with one member in my default queue), I got some really strange behaviour, aside from my hysterical laughing after hearing the default MOH =) I only have one SIP hardphone I'm testing with right now, so I tested using DIAX, Firefly(IAX) and XLite(SIP). My hardphone is an analog

Hello, I am just asking this because I am note sure if the problem is on my side or not, I saw some comments on SIP realtime today so I was wondering, has anybody has SIP realtime working with a softfone ? If yes, please confirm, that would give me a light. My previous message to the list is below. Thanks. Frederic ----- Original Message ----- From: Frederic Jean To:

Hi all, i have a problem with 2 peers conecting to an asterisk machine, both are conected behind nat without any port mapping in the router, and the * is conected behind other nat with the port 4569 mapped to it address, the problem is: when a peer register to the asterisk the other cant register and viceversa, only gets registration the first one, im using firefly and a hardphone from wuchuan,

I have progressinband=yes in sip.conf, but Asterisk sends a 180-Ringing to my polycom phones and then it also sends 183-Session Progress. That doesn't seem to make sense. Shouldn't Asterisk NOT send 180-Ringing if progressinband=yes ? Doug.

I upgraded my Cisco7960 to SIP 8-2 from 7-4. Everything seems ok, works fine. Except that when I make an outbound call, I get a double-ring sound. I also found that if the target number is engaged, I get a ring sound and at the same time get a busy sound. If I revert back to 7-4, there is no problem. Anyone else had this, or any clues on how to fix it ? All of our other phones are still on

Andrew, I don't think it's a Polycom issue. We took Asterisk out of the picture and had our Polycom phones communicate directly with an Audiocodes PSTN gateway. Unlike Asterisk, the audiocodes do not send 180 Ringing before sending 183 Session Progress, and the polycom's play the correct tones in this case. We WANT Asterisk to send progress tones in band. In our case it IS needed.

Chris Abel writes: >Hello everyone! > >I've had this problem for a while and cant figure it out. When an outside >caller calls an extension on my asterisk system, they do not hear any >sort of ringing. Inside extensions calling other extensions do hear >ringing. We have 3 other asterisk systems that are configured the same >way, but do not have this problem. We think it

I have Polycom ip-300 phones that worked yesterday but dont seem to work today (at least dtmf signalling once connected to the asterisk box) The current configuration is: [general] port = 5060 bindaddr = 0.0.0.0 context = test srvlookup = yes dtmf = inband allow = all dtmfmode=inband progressinband=no disallow=all allow=ulaw pedantic=no [202] type=user secret=xxxx context=test mailbox=202

Hello, I have Asterisk-1.8.3.2, dahdi-linux-complete-2.4.1+2.4.1, and libpri-1.4.11.5 installed and running on a Ubuntu 10.04 server all built from source. Everything is working nicely except one small issue. The CDR records are stored in the CSV file correctly and complete. The MySQL storage is working as it should and is automatically updating all the fields except the CLID field. I have

Hello, My target system is : PSTN <---> Sip Provider <---IP/ADSL---> Router with fw/NAT <--- SIP/IP/Eth --> Asterisk <--- SIP/IP/Eth --> SIP Phones Asterisk is configured to keep NAT connection with SIP provider open (with qualifyfreq) so I don't have any problem (yet) with either casual incoming or outgoing calls. To work around a possible No Audio when an incoming

Hi, i have a problem with iax2 and ringtone. Here is the call path pstn -> asterisk -> iax -> firefly or any iax phone. My problem is when i receive a call on my iax phone, the ring sound is very distort and bad. If i open my sip phone, and receive a call from my pstn, the ring is like dring dring, very normal. Otherwise, it is like a machine gun with iax Help would be really