Displaying 20 results from an estimated 20000 matches similar to: "Broken faxes when other call disconnects"
2006 Feb 01
6
Receiving faxes with spandsp - strange problem
Hello,
I'm trying to receive faxes with asterisk. My configuration is like this:
PSTN fax -> ISDN -> Cisco router with VoIP module -> Asterisk
When I try to send a fax from PSTN fax I got the standard fax signal,
Asterisk starts rxfax application and then call ends and there is no tif
anywhere. On the fax display there is still one message: Calling...
Part of my extensions.conf:
2005 May 15
1
Re: SpanDSP TXFax and multipage faxes problems (aditional info)
Thanks for the information Lee !
Still, something is still strange to me, since this two Panasonic Fax
machines are receiving at least 20 multi-paged faxes a day (they are in same
office as both Asterisk boxes, and me :) ). Beside that, POTS lines in those
two faxes
are from same PSTN switch as line in X100P in one of Asterisk boxes, and the
ISDN PRI lines in other Asterisk box is from same PSTN
2005 May 15
1
Re: SpanDSP TXFax and multipage faxes problems (aditional info)
Hi everyone !
I have some aditional info on problem with TXFax and sending multi-page
TIFFs.
I have made 6 different multi-page TIFFs (Group3 1D with fillbits EOL
aligned - 3 pages one TIFF in lowres and one in hires, Group3 2D -3 pages
againg in both resolutions , and Group 4 - 3pages in both resolutions), and
then tried to send them to Panasonic KX-F1100, Panasonic KX-F500 and SpanDSP
2006 Jan 08
0
Advice on fax support
Just this week, I've installed an Asterisk solution for my current job, to
replace a single POTS line which was shared between voice and fax.
Before we go fully live with the solution, we need to come up with a solution
to what to do with the current POTS line. The company is very keen to retain
the line (or at least the number) as it has been in mail signatures, etc, for
the past year or
2005 May 16
1
Re: SpanDSP TXFax and multipage faxes problems (aditional info)
OK I see the ponit (although I never said that second page is interrupted -
I said that in some combinations of resolutions and TIFF options receiving
fax "spits" another blank sheet of paper beside the clearly received first
page).
I have read someware (some faxing tutuorial) that there is some kind of
control code (6 EOLs I belive) that should be in TIFFs between pages and
that
2005 Jul 13
2
Faxing Suggestions
I wrote a week or two ago about a problem I was having with a TDM400P
with 2 FXS. The problem was reliable fax transfers. There were often
slow or had communication failures during transmission.
Richard replied to my post and told me this is an ongoing problem that
might have a solution in the weeks to come. However, I was wondering
if anyone had any alternate solutions for faxing with an
2006 Feb 02
0
Re: 5, 000 concurrent calls system rollout question
Why is using ulaw or alaw an unlikely scenario? I wouldn't use anything but
ulaw\alaw. The Bells can compete on price and will if they have to. Where
they CAN'T compete is quality. If there were something better than 711, I'd
offer that. Well, there is 722, but not many things support it.
----
Mike Hammett
Intelligent Computing Solutions
http://www.ics-il.com
----- Original
2004 Dec 07
7
Faxing..not 100%
Here is the setup:
POTS -> PRI -> Asterisk -> ATA (Fax)
The ATA is set to only 711. Asterisk's sip.conf sets this device to only
711. Yet, faxing works less than 50% of the time.
I cannot possibly be the only person with this problem. I can't even get
app_rxfax to work. It answers but rxfax drops the call 5 seconds into it.
If anyone out there has near 100% success with
2006 Mar 08
1
Calls forwarding to numbers only in user's context
Hello,
I'm trying to do call forwarding based on this:
http://www.voip-info.org/wiki/view/Asterisk+call+forwarding
In the extensions.conf file I have several context defined (local,
longdistance, mobile, international and so on). Each user can be
associated with different context (so can make only i.e. local calls).
How to set calls forwarding only to numbers that are available in
2003 Sep 26
1
Cisco 2600 and ASTERISK and calling out
You have no dial-peer telling the router what to do with the outbound call.
http://www.tape.net/~gerry/asterisk/cisco26x0.html
At 12:50 PM 9/26/2003, you wrote:
>Like Gerry wrote for callerid you need VIC-2FXO-M1 card.
>
>Right now I am stuck on making outgoing call.
>
>Could soembody help me with the configuration.
>
>On cisco I have soemthing like that:
>
>dial-peer
2005 Feb 22
2
SpanDSP - Still can't send
I have googled until blie in the face, WiKi'd until physically exhausted
and searched through every Asterisk repository that I can find, all to
no avail...
No matter which version of SpanDSP I use, with which version of libtiff,
Asterisk, ... I simply cannot send faxes.
I can receive faxes *perfectly* (sending from standard fax macine on
POTS) into tiff file (via Digium analogue card),
2005 Mar 11
0
Sipura 2100 and Asterisk and Fax
I've just made an interesting observation that I'd like to share with
you all: the popular Sipura SPA-2100 just doesn't seem to be as great
as I'd hoped.
I've been trying to get inbound AND outbound faxing working via
Asterisk and at least one of my termination services: Voicepulse or
Sixtel. In general, inbound has been working flawlessly but outbound
has been pretty
2007 Dec 10
1
T.38 fax solution, opinions?
Hi,
I'm putting together a fax solution for my company that utilizes T.38. I
wanted to throw out my plan and get some feedback if anyone is doing
something similar or sees a blatant problem with it.
We're currently rolling out SPA-942 phones for the standard desk phone with
vanilla Asterisk 1.4.15 (just upgraded it today) on the back end. Most calls
for satellite offices are handled by
2010 Feb 18
3
Asterisk t38modem Fax gateway evaluation
Hi,
I am trying to fix a Asterisk setup with buggy (POTS) Fax machines. The
setup consists of the following components:
- A Digium TE121 for connectiong to E1 ISDN
- Debian box with Asterisk 1.4
- Grandstream GXW-4008 SIP ATA to which the Fax machines connect
I am aware of the problems with this type of ISDN <-> Asterisk <-> SIP
ATA <-> Fax machine installations, e.G.
2006 Feb 22
0
Problem with receiving faxes with spandsp - full log included (long)
Hello,
I have spandsp working with asterisk (tested on one PSTN fax machine).
Today someone wanted to send me a fax, but there was a problem with the
TIFF file. This is what asterisk console says:
TIFFReadDirectory: /var/spool/asterisk/fax/1140608321.7.tif: cannot
handle zero number of strips.
MissingRequired: /var/spool/asterisk/fax/1140608321.7.tif: TIFF
directory is missing required
2013 Oct 30
1
dahdi fax catch-22
I've got a Digium Wildcard TDM410P with one POTS line and three
extensions. One of the extensions is connected to a fax modem. This kind
of works, but there's a gotcha. If I set faxdetect=incoming in
chan_dahdi.conf, then incoming faxes do get routed to the modem and this
all works, but outbound faxes fail, with a message like this:
[Oct 29 21:57:09] WARNING[16732][C-00000000] app_dial.c:
2003 Sep 08
19
Fax
Hi all !
Let's say you have about 6 small different companies sharing the same E1
/ Asterisk server, and every company needs its own fax number. Since
they don't really need fax machines, what would be the most
cost-effective way to handle this (keeping fax-privacy at its best) ?
Is there a way to configure Hylafax or sth & one modem behind an ATA-186
to email faxes to different
2005 Sep 07
0
Max concurrent faxes with txfax/spandsp?
Hi,
I tried to use txfax to send several faxes at the
same time.
It seams, that one can't send more than 3 faxes at once,
or one risks to get 50% and more aborted faxes due to
errors.
The CPU usage is below 97%.
I tried with Opteron and IntelP4: same result.
Ok, I know, that faxing via a digital line is complicate,
and I shouldn't complain, but I would like to know, whether
these are
2005 Sep 15
2
Fax->Email for Hosted PBX
I'm proposing to install an Asterisk PBX at a collocation facility for a
remote customer. Each of the customer locations will have an SPA-3000
with the FXO port connecting a POTS circuit and the FXS port connecting
a fax machine or red phone.
In addition to voice traffic, the customer has a high volume of incoming
and outgoing faxes.
Would it be possible, using g711 between the SPA-3000
2010 Dec 14
1
Anyone know how to receive partial (interrupted) faxes with app_fax?
Hi Guys,
I've configured a fax support in my system with opensource
app_fax/spandsp 0.6 -
but there is a problem - if FAX transmission got interrupted - system
permanently returns
"The call dropped prematurely" - and no fax is submitted. This is
sometimes very inconvenient, say if someone have sent a multipage fax
with 20 pages, and it got interrupted on 19th page, the person will