Displaying 20 results from an estimated 500 matches similar to: "TE411P or TE406P"
2005 Oct 05
2
TE411P and TE406P stability
I am getting ready to purchase my first Digium card to start experimenting with Asterisk. Before I make my purchase, I wanted to make sure I'm not going to have issues with these cards (need to see what the specs are on my box, 5V or 3.3V PCI ). I will be using Asterisk @ Home, so will be Asterisk v1.0.9. I took a quick poke at the lists, and it appears several people have been having
2006 Feb 03
1
64bit processor and 32 bit digium card
Hi Guys,
Im planning to setup a server that has a 64bit processor and 32bit digium card using 64bit kernel of Linux.Id like to know if il be having a problem later on its compatibility and the availability of drivers or patches for 64bit zaptel.Because we all know the 64bit are not much matured enough.
Any comment and suggestion guys.Will highly appreciated.
2006 Feb 01
2
supermicro server model
Hi Guys,
Im planning to purchase Supermicro server but I dont have idea what Motherboard and chipset model will work with TE406P.I read one post here that the chipset should be Intel E7520.Is it true?Is there other recommendation?My requirement by the way is to handle 1000 simultaneous calls.
Does dualcore xeon (single cpu) and 2gig memory can handle this w/o
2006 Feb 05
11
TE411P Really Bad Echo
I just implemented a system using a TE411P hardware echo cancellation
card. Per Digium, I setup zaptel.conf, and zapata.conf the same way as
I always have. To my surprise calls out to the PSTN had a terrible
echo. 1 - 2 second delay, and quite clear. The echo was so bad that I
had to remove the hardware echo cancellation module from the card. We
are only using the 1st span of this card right
2006 Apr 14
1
Re: Asterisk-Users Digest, Vol 21, Issue 81
I too had a server room fry and need to replace h/w.
So what specific Dell servers did/do you deploy?
Where is the link w/Digium/s Dell caveats?
I'm using the Digium TDM400 card w/*
> Date: Thu, 13 Apr 2006 19:19:13 -0500 (CDT)
> From: Aaron Daniel <amdtech@shsu.edu>
> Subject: Re: [Asterisk-Users] Digium cards, so disappointing !
> To: Asterisk Users Mailing List -
2005 Sep 11
5
TE406p no interrupts
Hi,
I've installed an TE406p, asterisk1.2 on tyan opteron
board.
After installation there is no interrupts from TE406p.
Is this board stable?
Should i change * version to 1.0.9?
Regards,
Jason
__________________________________________________
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com
2005 Sep 06
3
TE406P audio drops
Hello,
Now that we've had our new Digium TE406P card in production for 4 days we
have discovered audio drop problems that happen randomly across all
channels. Here's more about our setup:
P4-3.2GHz 2GB ram
Slackware Linux 10.1 with custom kernel 2.4.29
Asterisk 1.2beta1
Digium TE406P quad T1 card with the following attached:
- 2 x RBS D4/AMI 24 channel T1s
- 1 x RBS B8ZS/ESF 24 channel
2005 Jul 24
2
success story: TE406P (quadspan with hardware echocan)
I just wanted to post here and let everyone know that the TE406P (quadspan
T1/E1 with hardware echo can) kicks some serious ass.
We've been running a PRI now for over a year with Asterisk (every single call
in and out is through two Asterisk boxes, including faxes) and while the
software based echo cancellation is more than adequate, we'd get the
occassional "edgy" echo and
2005 Oct 12
3
E400P vs te410p vs te411p
Hi,
I found E400P quad PRI card quite cheap (749USD):
http://www.govarion.com/product_info.php?cPath=1&products_id=2&osCsid=68cdd6e3d08754
in comparison to te410p (approx 1500 USD )
http://www.digium.com/index.php?menu=product_detail&category=hardware&product=TE410P
Now newer generation with HW echo canceling emerged (te411p).
I'm not sure in what things those two cards
2005 Sep 01
1
TE406P seg fault on Stable
I received a TE406P card from Digium yesterday and have done several tests
on it and cannot get it working reliably with any Stable release or even CVS
v1.0.
What are other people that are using the TE406P card using for an Asterisk
version?
I tried 1.2.0 beta1 and it seemed to function well except for an unrelated
issue with the beta release where the manager interface chokes under
2006 Mar 22
1
Stability and motherboard questions with TE406P and TE410P
I am having a problem with asterisk not being stable enough for production
use. I have two cards, the digium TE406P, and the TE410P. The TE410P is
the primary card that I am using but I would like to move to the TE406P for
the echo cancellation and more flexibility of PCI slots available.
General config info:
3 PRIs, configured as such:
span=1,2,0,esf,b8zs
span=2,0,0,esf,b8zs
2006 May 24
2
TE406P - MFC/R2
Guys,
I'm trying to configure a TE406P with MFC/R2.
here goes my zaptel.conf:
span=1,0,0,ccs,hdb3,crc4
cas=1-15:1101
dchan=16
cas=17-31:1101
span=2,0,0,ccs,hdb3,crc4
cas=32-46:1101
dchan=47
cas=48-62:1101
The first strange behavior is that the:
zap show status
shows this:
Description Alarms IRQ
bpviol CRC4
T4XXP (PCI) Card 0 Span 1
2005 Sep 08
2
TE411P zapata.conf, monitoring echo cancellation and echo tail size
Hi all,
1. Just bought a new TE411P and about to install it replacing the existing
TE410P. I am assuming I need to set echocancel=no and
echocancelwhenbridged=no now that it will be done in hardware, correct?
2. Is there any way to monitor hardware echo cancellation to ensure it is
working (apart from being on a call)?
3. The Digium webite says "By supporting 16ms with 128 channels or
2007 Feb 07
2
CPU & motherboard for 100+ simultaneouse calls on Digium Quad E1 TE411p
hi!
anyone please recommend/guide me of purchasing a resonably high performance
server system regarding processor(s) & motherboard (+ other compulsary
peripherals i.e. VGA, Soundcard). Mentioning up-to-date vendor+model will be
more helping
I've to use Digium TE411p Quad E1 card
signalling on the E1 is SS7
no. of simultaneouse calls is 100+
regards
-------------- next part
2006 Jun 20
10
TE420P/TE415P?
Hi,
I just read a pressrelease from VON that Digium will soon be releaseing
a couple of new cards. What got me interested was: "The TE420P and
TE415P support 128ms of G.168 (2002)-compliant echo cancellation across
their entire 128 channels."
Does anyone know when thease will be released and what they will cost
when released? Thanks!
2005 Aug 23
1
Asterisk 1.0.9: TE411P replacement for TE410P 1stgen causes crashes
Hi all,
I replaced a TE410P Rev C 1st Generation Firmware with a TE411P
without any cfg changes (zaptel/zapata).
As a result Asterisk crashes on outbound from PRI4 going to PRI1 calls:
Aug 23 18:22:00 WARNING[4693]: chan_zap.c:7545 zt_pri_error: PRI: !! Got a
UA, but i'm in state 1
Aug 23 18:22:00 WARNING[4693]: chan_zap.c:7545 zt_pri_error: PRI: !! Got a
UA, but i'm in state 1
2006 Jan 05
1
fax detection on TE406P
Hi all,
I am having problems detecting fax on a client site using the TE406P
(card with echo cancellation module) under 1.2 and was wondering if
anybody was having or has had similar problems?
Currently I can not get the system to detect fax for love nor money,
in zapata.conf the relevant entries are set to:
faxdetect=outgoing
and I have a fax extension in the necessary context.
I have taken
2006 Jan 20
1
Can TE406P provide PRI to other VoIP gateways?
Hi,
Does anyone know if it's possible to have 1 port of TE406P to provide
T1 PRI to other VoIP gateways?
I am trying to provide T1 PRI to one of our old Clarent gateways to
integrate it to Asterisk.
Can anyone help?
Thank you.
Andy
2006 Feb 09
1
4 TE411P in one server installation
Dear all,
Does anyone try to install 2 or multiple TE411 card into one server? Can it
be done? What about stability?
Thanks
Ray
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20060209/b65a1d46/attachment.htm
2006 Feb 11
1
TE411P Really Bad Echo ORION
The Orion echo canceller is just ok. The Tellabs units work just as well if you don't mind 10 mins of soldering.
I have the orion running with an adit 600 and a TE110P. Echo cancel is fairly good, but I have loads of problems with DTMF digits.
-Darren
________________________________
From: asterisk-users-bounces@lists.digium.com